This patch adds the ACPI/PNP ID. The AD5592/3 driver core is already
designed around the unified device property API.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds the ACPI/PNP ID. The AD5592/3 driver core is already
designed around the unified device property API.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds a driver for the Capella Microsystems CM3605 Ambient
Light Sensor and proximity sensor. This is a pretty simple entirely
analog device that is interfaced with the target system using
the POUT (proximity out) and AOUT (ambient light out) signals.

The POUT signal is a simple high/low signal that indicates whether
an object is in proximity, most typically used to detect a face
in front of a mobile device. The signal requires that an infrared
LED is mounted next to the device, making IR light reflect off
the object in proximity and triggering the POUT signal. We grab
a GPIO pin to handle the POUT signal as an interrupt line and
register this as an event channel for the sensor.

Since the proximity sensor requires an IR LED, we add a LED trigger
named "cm3605" so that the infrared LED can just associate with
this trigger to be sure it is always on when the proximity sensor
needs it.

The AOUT is an analog voltage between 0 and 1550 mV that indicate
the LUX value in the ambient light: this is orthogonal to the
proximity sensor functionality. Since this analog voltage needs
to be converted into a digital value, the driver grabs an IIO
channel named "aout" associated with the device.

This patch created a combined ALS and proximity sensor driver.
The former supports raw reads of the LUX value and the latter
will generate proximity events.

To integrate this properly with Linux we also add a supply
regulator for the VDD pin (driving both functions) and add device
tree bindings to define the RSET resistor that in turn configures
the luminosity range of the ALS sensor.

Since the sensor needs to be on more or less constantly, we
restrict the power management to system suspend/resume: we
disable the IR LED and disable the regulator for VDD on suspend
and take them back up on resume.

Tests:
cd /sys/bus/iio/devices/iio:device1
cat in_illuminance_raw
304
(hold hand over sensor)
cat in_illuminance_raw
17
iio_event_monitor cm3605
Found IIO device with name cm3605 with device number 1
(hold hand over sensor)
Event: time: 2444842301447, type: proximity, channel: 0,
  evtype: thresh, direction: falling
(remove hand over sensor)
Event: time: 2445583440706, type: proximity, channel: 0,
  evtype: thresh, direction: rising

Cc: Capella Microsystems <capellamicro@gmail.com>
Cc: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds device tree bindings for the Capella Microsystems CM3605
ambient light sensor and short range proximity sensor.

Cc: devicetree@vger.kernel.org
Cc: Capella Microsystems <capellamicro@gmail.com>
Cc: Kevin Tsai <ktsai@capellamicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

There is one light sensor type defined in the sensor hub specification,
which has one Illuminance field. It doesn't distinguish between ambient
light sensor or color sensor. Currently it is presented as IIO_INTENSITY
channel. There are some user spaces specifically looking for IIO_LIGHT
channel.
To satisfy such user spaces this change also add a duplicate IIO_LIGHT
channel. The units of measurement of Illuminance field is Lux, so it is
still compatible to IIO ABI.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Both devices are using the same iio_chan_spec to define which settings
are exported with sysfs. Both are properly configured to set/get
sampling frequency for pressure and temperature. They also properly
export available sampling frequencies. The only missing thing is
sampling_frequency sysfs file, which allows to set/get this property
from userspace.

Add sampling frequency to iio channel info mask, so sampling_frequency
file is properly exported using sysfs.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Datasheet of each device (lps331ap, lps25h, lps001wp, lps22hb) says that
the pressure and temperature data is a 2's complement.

I'm sending this the slow way, as negative pressures on these are pretty
unusual and the nature of the fixing of multiple device introduction patches
will make it hard to apply to older kernels - Jonathan.

Fixes: 217494e5 ("iio:pressure: Add STMicroelectronics pressures driver")
Fixes: 2f5effcb ("iio: pressure-core: st: Expand and rename LPS331AP's channel descriptor")
Fixes: 7885a8ce ("iio: pressure: st: Add support for new LPS001WP pressure sensor")
Fixes: e039e2f5 ("iio:st_pressure:initial lps22hb sensor support")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds documentation for Bosch BMI160 Inertial Measurement Unit
device-tree bindings.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

From now on we can add bmi160 device to device-tree by specifying
compatible string.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

From now on we can add bmi160 device to device-tree by specifying
compatible string.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

according to datasheet complete control register is of 2 bytes.
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdfSigned-off-by: Nizam Haider <nijam.h@hcl.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Several ADC channels are supported in PMIC which can be used to
measure voltage, temperature, current etc. Different scaling can be
applied on the obtained voltage to report in physical units. Scaling
functionality can be different per channel. Add scaling support per
channel. Every channel present in adc has an unique conversion formula
for obtained voltage. Add support to report in Raw as well as in
processed format. Scaling is applied when processed read is requested
and is not applied when a Raw read is requested.
Signed-off-by: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Several channels are supported in ADC of PMIC which can be used to
measure voltage, temperature, current etc., Hardware provides
readings for all channels in adc code. That adc code needs to be
converted to voltage. Logic for conversion of adc code to voltage
is common for all ADC channels(voltage, temperature, current
.,etc). Implement separate function for generic conversion logic.
Signed-off-by: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The alignment of the #defines at the top of the file is not consistent.
This changes all of the defines to use consistent alignment to improve
the code readability.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

isl29028_chip_init() contains the device driver defaults and
two I2C calls that detect the presence of the chip. This patch
moves these into isl29028_probe() so that this function can
be used by the power management runtinme in a followup patch. This
patch also renames isl29028_chip_init() to
isl29028_chip_init_and_power_on().
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

There are two callers to the function isl29028_set_als_ir_mode() and
both instances use a nested if statement to only change the chip state
if it is not in the proper mode. This patch moves this check into the
isl29028_set_als_ir_mode() function to remove the nested if
statements.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

At the end of function ad7150_write_event_config(), directly returns 0.
As a result, the errors will be ignored by the callers. It may be better
to return variable "ret".
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

In function cm3232_reg_init(), it returns 0 even if the last call to
i2c_smbus_write_byte_data() returns a negative value (indicates error).
As a result, the return value may be inconsistent with the execution
status, and the caller of cm3232_reg_init() will not be able to detect
the error. This patch fixes the bug.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188641Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch fixes the following checkpatch.pl warning in ad7150.c
WARNING: Symbolic permissions 'S_IRUGO | S_IWUSR' are not preferred
Occured during build.
Signed-off-by: Amit Kushwaha <kushwaha.a@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Added timestamp channel. With this change, each sample has a timestamp.
This timestamp can be from the sensor hub when present or local kernel
timestamp. HID sensors can send timestamp with input data using usage id
HID_USAGE_SENSOR_TIME_TIMESTAMP. This timestamp value is converted to
nano seconds before pushing this sample to the iio core.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

msleep(1~20) may not do what the caller intends, and will often sleep longer.
(~20 ms actual sleep for any value given in the 1~20ms range)
This is not the desired behaviour for many cases like device resume time,
device suspend time, device enable time, data reading time, etc.
Thus, change msleep to usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The copyright year can not be in the future.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The module descriptions for the ADIS 16201, 16203 and 16209 drivers do not
match the actual function of the devices. Update them accordingly to fix
this.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

smatch warned:
	sval_binop_signed: invalid divide LLONG_MIN/-1

and this fixes it. It's actually good to have, in order to avoid accidental
checking for negative return values here.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Support driver probe by reading unique HID on systems based on ACPI instead
of DT compatible strings.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Compatible strings are not available on ACPI based systems. This patch adds
support to use DSDT information read from platform BIOS instead for probing
st pressure sensors.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add support to probe st_accel sensors on i2c bus using ACPI. Compatible
strings are not avaialable on ACPI based systems.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add support to match st sensors using information passed from ACPI DST
tables.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove two passthrough macros that are only called from a single
location and make the resultant vmcall directly.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the already defined DIAG_SEVERITY values directly instead of special
postcode macro names.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There were two instances of FAILURE being misspelled in the s-Par
firmware postcode event enum that are fixed.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove guestlinuxdebug enum values that are no longer being used and
renumber remaining values accordingly.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The visorchipset.c functionality was moved into the visorbus driver
previously. This patch updates the s-Par firmware postcode values to
reflect this status.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_4.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_3.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Call POSTCODE_LINUX directly instead of passing through POSTCODE_LINUX_2.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use CURRENT_FILE_PC directly in the POSTCODE_LINUX macro instead of
relying on passthrough macros to provide it.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Leverage the 3 existing s-Par postcode macros to do a bit more work
and provide only 1 base postcode macro.
Signed-off-by: Bryan Thompson <bryan.thompson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes all the unused pound defines currently in
vbuschannel.h.
Signed-off-by: Erik Arfvidson <erik.arfvidson@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>