Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].

This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.

This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

On x86 the AXP288 PMIC provides an ACPI OpRegion handler, which must be
available before other drivers using it are loaded, which can only be
ensured if the MFD, OpRegion and i2c-bus drivers are built-in.

Since the AXP20x MFD code is used on non x86 too we cannot simply change
this into a bool, I've tried some Kconfig magic with if x86 but I could
not get this working correctly, so this commit just documents that this
should be built-in on x86, which fixes errors like these during boot:

mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion]
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-2
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b
acpi 80860F14:02: Failed to change power state to D0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add mfd driver for Intel CHT Whiskey Cove PMIC, based on various non
upstreamed CHT Whiskey Cove PMIC patches.

This is a somewhat minimal version which adds irqchip support and cells
for: ACPI PMIC opregion support, the i2c-controller driving the external
charger irc and the pwrsrc/extcon block.

Further cells can be added in the future if/when drivers are upstreamed
for them.

[The above patch caused a build error on some archetectures]

From: Arnd Bergmann <arnd@arndb.de>

I ran into a build error on ARM with a platform that has a non-standard
clk implementation:

drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here

The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.

This turns all three into 'depends on', as it should be.

Finally, we can limit the build to x86, unless we are compile testing.

First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The SIMATIC IOT2020 and IOT2040 are derived from the Galileo Gen2 board
and share its I2C frequency.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Avoids reimplementation of DMI matching in intel_quark_i2c_setup.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Usage of  devm_of_platform_populate() simplify driver code
by allowing to delete cpcap_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Usage of  devm_of_platform_populate() simplify driver code
by allowing to delete pmic_spmi_remove().
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_of_platform_populate() to be sure that of_platform_depopulate
is called when removing the driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use devm_of_platform_populate() instead of of_platform_populate()
and suppress stm32_timers_remove() which become useless.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The Crystal Cove PMIC provides an ACPI OPRegion handler, which must be
available before other drivers using it are loaded, which is why
INTEL_SOC_PMIC is a bool.

Just having the driver is not enough, the driver for the i2c-bus must
also be built in, to ensure this, this patch adds a select for it.

This fixes errors like these during boot:

mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion] (20170119/evregion-166)
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-299)
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93543b0cde10), AE_NOT_EXIST (20170119/psparse-543)
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b0b5cd0), AE_NOT_EXIST (20170119/psparse-543)
acpi 80860F14:02: Failed to change power state to D0

While at it this patch also changes the human readable name of the Kconfig
option to make clear the INTEL_SOC_PMIC option selects support for the
Intel Crystal Cove PMIC and documents why this is a bool.

[The above patch caused a build error on some archetectures]

From: Arnd Bergmann <arnd@arndb.de>

I ran into a build error on ARM with a platform that has a non-standard
clk implementation:

drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here

The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.

This turns all three into 'depends on', as it should be.

Finally, we can limit the build to x86, unless we are compile testing.

First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Additions to search terms for files supported by Dialog Semiconductor.
This update will allow Dialog support to follow files for device tree
bindings (onkey, thermal and watchdog) and source code for chip thermal
monitoring drivers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

As silently failing isn't that nice, emit an error message at a place
that was silent on failure up to now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Link to the generic GPIO specifier bindings now that the second cell of
the binding has some support in the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add NULL check before dereferencing pointer of_id in order to avoid
a potential NULL pointer dereference.

Addresses-Coverity-ID: 1408830
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add NULL check before dereferencing pointer of_id in order to avoid
a potential NULL pointer dereference.

Addresses-Coverity-ID: 1408829
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The request should be resent when DMA transfer error occurred.
For rts5227, the clock rate needs to be reduced when error occurred.
Signed-off-by: Steven Feng <steven_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

As axp20x-regulator now supports AXP803, add a cell for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Remove the restart handler registered in probe on device remove.

Fixes: a370f60a ("mfd: rn5t618: Register restart handler")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Since a copy of the pdata was added into the core struct in
commit f6dd8449 ("mfd: wm831x: Add basic device tree binding")
the pdata pointer in probe can no longer be NULL. As such remove
the redundant checks for this case.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

These hexdumps get printed no matter if CONFIG_DEBUG is set or
not. Just get rid of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Intel Cannonlake PCH has the same LPSS than Intel Kabylake. Add the new IDs
to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Currently in WCOVE PMIC MFD driver, all second level IRQ chips
are chained to the respective first level IRQs. So there is no
need for explicitly unmasking the first level IRQ in this
driver. This patches removes this level 1 IRQ unmask support.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Whishkey cove PMIC has support to mask/unmask interrupts at two levels.
At first level we can mask/unmask interrupt domains like TMU, GPIO, ADC,
CHGR, BCU THERMAL and PWRBTN and at second level, it provides facility
to mask/unmask individual interrupts belong each of this domain. For
example, in case of TMU, at first level we have TMU interrupt domain,
and at second level we have two interrupts, wake alarm, system alarm that
belong to the TMU interrupt domain.

Currently, in this driver all first level IRQs are registered as part of
IRQ chip(bxtwc_regmap_irq_chip). By default, after you register the IRQ
chip from your driver, all IRQs in that chip will masked and can only be
enabled if that IRQ is requested using request_irq() call. This is the
default Linux IRQ behavior model. And whenever a dependent device that
belongs to PMIC requests only the second level IRQ and not explicitly
unmask the first level IRQ, then in essence the second level IRQ will
still be disabled. For example, if TMU device driver request wake_alarm
IRQ and not explicitly unmask TMU level 1 IRQ then according to the default
Linux IRQ model,  wake_alarm IRQ will still be disabled. So the proper
solution to fix this issue is to use the chained IRQ chip concept. We
should chain all the second level chip IRQs to the corresponding first
level IRQ. To do this, we need to create separate IRQ chips for every
group of second level IRQs.

In case of TMU, when adding second level IRQ chip, instead of using PMIC
IRQ we should use the corresponding first level IRQ. So the following
code will change from

ret = regmap_add_irq_chip(pmic->regmap, pmic->irq, ...)

to,

virq = regmap_irq_get_virq(&pmic->irq_chip_data, BXTWC_TMU_LVL1_IRQ);

ret = regmap_add_irq_chip(pmic->regmap, virq, ...)

In case of Whiskey Cove Type-C driver, Since USBC IRQ is moved under
charger level2 IRQ chip. We should use charger IRQ chip(irq_chip_data_chgr)
to get the USBC virtual IRQ number.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Revieved-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Cleanup the resource allocation/free code in probe function by using
devm_* calls.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Currently all PMIC GPIO domain IRQs are consumed by the same
device(bxt_wcove_gpio), so there is no need to export them as
separate interrupts. We can just export only the first level
GPIO IRQ(BXTWC_GPIO_LVL1_IRQ) as an IRQ resource and let the
GPIO device driver(bxt_wcove_gpio) handle the GPIO sub domain
IRQs based on status value of GPIO level2 interrupt status
register. Also, just using only the first level IRQ will eliminate
the bug involved in requesting only the second level IRQ and not
explicitly enable the first level IRQ. For more info on this
issue please read the details at,

https://lkml.org/lkml/2017/2/27/148

This patch also makes relevant change in Whiskey cove GPIO driver to
use only first level PMIC GPIO IRQ.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Since all second level thermal IRQs are consumed by the same
device(bxt_wcove_thermal), there is no need to expose them as separate
interrupts. We can just export only the first level IRQs for thermal and
let the device(bxt_wcove_thermal) driver handle the second level IRQs
based on thermal interrupt status register. Also, just using only the
first level IRQ will eliminate the bug involved in requesting only the
second level IRQ and not explicitly enable the first level IRQ. For
more info on this issue please read the details at,

https://lkml.org/lkml/2017/2/27/148

This patch also makes relevant change in bxt_wcove_thermal driver to use
only first level PMIC thermal IRQ.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

TMU interrupts are registered as a separate interrupt chip, and
hence it should start its interrupt index(BXTWC_TMU_IRQ) number
from 0. But currently, BXTWC_TMU_IRQ is defined as part of enum
bxtwc_irqs_level2 and its index value is 11. Since this index
value is used when calculating .num_irqs of regmap_irq_chip_tmu,
it incorrectly reports number of IRQs as 12 instead of actual
value of 1.

This patch fixes this issue by creating new enum of tmu IRQs and
resetting its starting index to 0.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull some more input subsystem updates from Dmitry Torokhov:
 "An updated xpad driver with a few more recognized device IDs, and a
  new psxpad-spi driver, allowing connecting Playstation 1 and 2 joypads
  via SPI bus"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: cros_ec_keyb - remove extraneous 'const'
  Input: add support for PlayStation 1/2 joypads connected via SPI
  Input: xpad - add USB IDs for Mad Catz Brawlstick and Razer Sabertooth
  Input: xpad - sync supported devices with xboxdrv
  Input: xpad - sort supported devices by USB ID

Pull UBI/UBIFS updates from Richard Weinberger:

 - new config option CONFIG_UBIFS_FS_SECURITY

 - minor improvements

 - random fixes

* tag 'upstream-4.12-rc1' of git://git.infradead.org/linux-ubifs:
  ubi: Add debugfs file for tracking PEB state
  ubifs: Fix a typo in comment of ioctl2ubifs & ubifs2ioctl
  ubifs: Remove unnecessary assignment
  ubifs: Fix cut and paste error on sb type comparisons
  ubi: fastmap: Fix slab corruption
  ubifs: Add CONFIG_UBIFS_FS_SECURITY to disable/enable security labels
  ubi: Make mtd parameter readable
  ubi: Fix section mismatch

Pull UML fixes from Richard Weinberger:
 "No new stuff, just fixes"

* 'for-linus-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Add missing NR_CPUS include
  um: Fix to call read_initrd after init_bootmem
  um: Include kbuild.h instead of duplicating its macros
  um: Fix PTRACE_POKEUSER on x86_64
  um: Set number of CPUs
  um: Fix _print_addr()

Merge misc fixes from Andrew Morton:
 "15 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm, docs: update memory.stat description with workingset* entries
  mm: vmscan: scan until it finds eligible pages
  mm, thp: copying user pages must schedule on collapse
  dax: fix PMD data corruption when fault races with write
  dax: fix data corruption when fault races with write
  ext4: return to starting transaction in ext4_dax_huge_fault()
  mm: fix data corruption due to stale mmap reads
  dax: prevent invalidation of mapped DAX entries
  Tigran has moved
  mm, vmalloc: fix vmalloc users tracking properly
  mm/khugepaged: add missed tracepoint for collapse_huge_page_swapin
  gcov: support GCC 7.1
  mm, vmstat: Remove spurious WARN() during zoneinfo print
  time: delete current_fs_time()
  hwpoison, memcg: forcibly uncharge LRU pages

Commit 4b4cea91691d ("mm: vmscan: fix IO/refault regression in cache
workingset transition") introduced three new entries in memory stat
file:

 - workingset_refault
 - workingset_activate
 - workingset_nodereclaim

This commit adds a corresponding description to the cgroup v2 docs.

Link: http://lkml.kernel.org/r/1494530293-31236-1-git-send-email-guro@fb.comSigned-off-by: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>