IA64 SMP systems were seeing TX issues with multiple cpu's attempting
to write tail registers unordered. This mmiowb() fixes the issue.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>

Enable early receives on 82573 for jumbo frame performance. Jumbo's
are only supported on 82573L with ASPM disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

Enable TSO for IPV6. All e1000 hardware supports it. This reduces CPU
utilizations by 50% when transmitting IPv6 frames.

Fix symbol naming enabling ipv6 TSO. Turn off TSO6 for 10/100.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

Remove debugging code disabling MULR (multiple reads). It's not usable
for a wide audience and there are no known problems with MULR right
now.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

Small whitespace changes, comment changes, typo fixes.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

Tested by Newsome on IRC

zd1211 chip 0586:3401 v4330 high 00-13-49 AL2230_RF  pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds two new defines for the SIOCSIWMLME to cover all
kinds MLMEs (well, except REASSOC) through a ioctl.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The current bcm43xx driver does not contain code to handle PCI-E interfaces
such as the BCM4311 and BCM4312. This patch, originally written by Stefano
Brivio adds the necessary code to enable these interfaces.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Output signal strength information as part of iwlist scan - before it did
not output any signal strength related information.
Signed-off-by: Holden Karau <holden@pigscanfly.ca>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NET: prism54 - whitespace cleanup
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NET: prism54 - fix potential race in reset scheduling

There appears to be a race in reset scheduling logic - thread
responsible for reseting the interface should clear "reset
pending" flag before restarting the queue, otherwise timeout
handler might not schedule another reset even if it is needed.

This race is mostly theoretical as far as I can see but a race
nonetheless.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NET: atmel: whitespace cleanup
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NET: atmel - switch to using ARRAY_SIZE()
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NET: atmel - do not initialize array over and over again
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the SoftMAC version of the IEEE 802.11 stack, not all duplicate messages are
detected. For the most part, there is no difficulty; however for TKIP and CCMP
encryption, the duplicates result in a "replay detected" log message where the
received and previous values of the TSC are identical. This change adds a new
variable to the ieee80211_device structure that holds the 'seq_ctl' value for
the previous frame. When a new frame repeats the value, the frame is dropped and
the appropriate counter is incremented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Hi

this patch allow to set the mtu between 1500 and 2304 (max octets in an
MSDU) for devices using ieee80211 linux stack.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds a host_strip_iv_icv flag to ieee80211 which indicates that
ieee80211_rx should strip the IV/ICV/other security features from the payload.
This saves on some memmove() calls in the driver and seems like something that
belongs in the stack as it can be used by bcm43xx, ipw2200, and zd1211rw

I will submit the ipw2200 patch separately as it needs testing.

This patch also adds some sensible variable reuse (idx vs keyidx) in
ieee80211_rx
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iNexQ UR055g: Tested by Todor T Zviskov
zd1211 chip 1435:0711 v4330 high 00-10-a7 AL2230_RF pa0 g--

ZyXEL AG-225, FCC ID SI5WUB410: Tested by Nathan
zd1211 chip 0586:3409 v4810 full 00-13-49 AL7230B_RF pa0 g---

Yakumo QuickWLAN USB: Tested by EdB
zd1211 chip 0b3b:1630 v4330 high 00-01-36 RF2959_RF pa0 ---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The bcm43xx-softmac driver fails to set two quantities needed for
iwlist to compute wireless quality when scanning. As a result, userland
programs using the quality to determine the best connection fail.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The rest of 8390 conversions; ifdef cascade in 8390.h is gone now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

more 8390 conversions - mac8390, zorro8390 and hydra got the same treatment
as arm etherh; one more case in 8390.h ifdef cascade is gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

etherh and a handful of other odd drivers use different macros when building
8390.c.  Since we generate a single 8390.o and then link with it, in any
config with both oddball and normal 8390-based driver we will end up with
breakage in at least one of them.  Solution: take most of 8390.c into
lib8390.c and have 8390.c, etherh.c and the rest of oddballs #include it.
Helper macros are taken from 8390.h to whoever includes lib8390.c.  That
way odd drivers get separate instances of compiled 8390 stuff and stop
stepping on each other's toes.  8390.h gets cleaned up - we don't have
the cascade of ifdefs in there and are left with the stuff that can be
used by any 8390-based driver.  Current problems are exactly because of
that cascade - we attempt to choose the set of helpers by looking at config
and that, of course, doesn't work well when we have several sets needed
by various drivers in our config.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add MII ioctl support to the deprecated sk98lin driver.
This allows comparison with skge driver's PHY settings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add support for dumping the registers in the deprecated
sk98lin driver. This is allows for easier comparison with
settings in new skge driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pci_module_init() convertion in olympic.c
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This was spotted by coverity (cid #793).  All callers dereference dev
before calling this functions, and we dereference it earlier in the
function, when initializing lp.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Tobias Diedrich <ranma@tdiedrich.de> sayeth:

Vanilla forcedeth doesn't seem to support suspend and an ifdown/up-cycle is
needed to get it working again after suspend.  Francois Romieu's "Awfully
experimental" patch is working just fine for me (with message signalled
interrupts disabled) and has survived quite a few suspend/resume cycles.

So I'd very much like to see (at least partial, with msi disabled)
suspend support for forcedeth in mainline.

(Addresses http://bugzilla.kernel.org/show_bug.cgi?id=6398)

Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc; Jeff Garzik <jeff@garzik.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

 This patch fixes a couple of problems discovered with interrupt handling
in the phylib core, namely:

1. The driver uses timer and workqueue calls, but does not include
   <linux/timer.h> nor <linux/workqueue.h>.

2. The driver uses schedule_work() for handling interrupts, but does not
   make sure any pending work scheduled thus has been completed before
   driver's structures get freed from memory.  This is especially
   important as interrupts may keep arriving if the line is shared with
   another PHY.

   The solution is to ignore phy_interrupt() calls if the reported device
   has already been halted and calling flush_scheduled_work() from
   phy_stop_interrupts() (but guarded with current_is_keventd() in case
   the function has been called through keventd from the MAC device's
   close call to avoid a deadlock on the netlink lock).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>

patch-mips-2.6.18-20060920-phy-irq-16
Signed-off-by: Jeff Garzik <jeff@garzik.org>

 The <linux/phy.h> uses some types and macros defined in
<linux/ethtool.h>, <linux/mii.h>, <linux/timer.h> and <linux/workqueue.h>,
but fails to include these headers.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>

patch-mips-2.6.18-20060920-include-phy-16
Signed-off-by: Jeff Garzik <jeff@garzik.org>

 This patch adds support for interrupt-driven operation of the Broadcom
Gigabit Ethernet PHYs.  I have included device IDs for the parts used on
Broadcom SiByte evaluation boards; more can be added as a need arises.
They are apparently generally software-compatible with one another.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>

patch-mips-2.6.18-20060920-broadcom-phy-15
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  [PATCH] Fix an offset error when reading the CS89x0 ADD_PORT register
  [PATCH] spidernet: poor network performance
  [PATCH] Spidernet: remove ETH_ZLEN check in earlier patch
  [PATCH] bonding: fix an oops when slave device does not provide get_stats
  [PATCH] drivers/net: SAA9730: Fix build error
  Revert "[PATCH] zd1211rw: Removed unneeded packed attributes"
  [PATCH] zd1211rw: Fix of a locking bug
  [PATCH] softmac: remove netif_tx_disable when scanning
  [PATCH] ieee80211: Fix kernel panic when QoS is enabled

* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] MIPS RM9000 on-chip watchdog device - patch 4
  [WATCHDOG] MIPS RM9000 on-chip watchdog device - patch 3
  [WATCHDOG] MIPS RM9000 on-chip watchdog device - patch 2
  [WATCHDOG] MIPS RM9000 on-chip watchdog device - patch 1
  [WATCHDOG] MIPS RM9000 on-chip watchdog device
  [WATCHDOG] Add iTCO vendor specific support
  [WATCHDOG] sc1200wdt.c pnp unregister fix.
  [WATCHDOG] config.h removal
  [WATCHDOG] NS pc87413-wdt Watchdog driver - fixes
  [WATCHDOG] NS pc87413-wdt Watchdog driver v1.1
  [WATCHDOG] NS pc87413-wdt Watchdog driver

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] libata: add missing sht->slave_destroy
  [PATCH] ahci: ignore PORT_IRQ_IF_ERR on JMB controllers

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (31 commits)
  [MIPS] Remove duplicate ISA DMA code for 0 DMA channel case.
  [MIPS] Remove unused definition of cpu_to_lelongp()
  [MIPS] Remove userspace proofing from <asm/bitops.h>.
  [MIPS] Remove old junk left from old atomic_lock.
  [MIPS] Use conditional traps for BUG_ON on MIPS II and better.
  [MIPS] mips HPT cleanup: make clocksource_mips public
  [MIPS] do_IRQ cleanup
  [MIPS] Avoid dupliate D-cache flush on R400C / R4400 SC and MC variants.
  [MIPS] Remove redundant r4k_blast_icache() calls
  [MIPS] Work around bogus gcc warnings.
  [MIPS] Fix double inclusions
  [MIPS] use generic_handle_irq, handle_level_irq, handle_percpu_irq
  [MIPS] IRQ cleanups
  [MIPS] mips hpt cleanup: get rid of mips_hpt_init
  [MIPS] PB1200: Remove duplicate definitions
  [MIPS] Fix alignment hole in struct cache_desc; shrink struct.
  [MIPS] Oprofile: kernel support for the R10000.
  [MIPS] Remove unused R10000 performance counter definitions.
  [MIPS] Add support for kexec
  [MIPS] Don't print presence of WAIT instruction on bootup.
  ...

* 'for-2.6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  SELinux: validate kernel object classes and permissions
  SELinux: ensure keys constant in hashtab_search
  SELinux: export object class and permission definitions
  SELinux: remove current object class and permission validation mechanism

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (25 commits)
  IB/ucm: Fix deadlock in cleanup
  IB/cm: Fix automatic path migration support
  IPoIB: Fix skb leak when freeing neighbour
  IB/srp: Fix memory leak on reconnect
  RDMA/addr: list_move() cleanups
  RDMA/addr: Fix some cancellation problems in process_req()
  RDMA/amso1100: Prevent deadlock in destroy QP
  IB/mthca: Fix initial SRQ logsize for mem-free HCAs
  IB/ehca: Use WQE offset instead of WQE addr for pending work reqs
  RDMA/iwcm: Fix comment for iwcm_deref_id() to match code
  RDMA/iwcm: Remove unnecessary function argument
  RDMA/iwcm: Remove unnecessary initializations
  RDMA/iwcm: Fix memory leak
  RDMA/iwcm: Fix memory corruption bug in cm_work_handler()
  IB: Convert kmem_cache_t -> struct kmem_cache
  IB/ipath: Fix typo in pma_counter_select subscript
  RDMA/amso1100: Fix section mismatches
  IB/mthca: Fix section mismatches
  IB/srp: Increase supported CDB size
  RDMA/cm: Remove setting local write as part of QP access flags
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
  usbcore: remove unused argument in autosuspend
  USB: keep count of unsuspended children
  USB hub: simplify remote-wakeup handling
  USB: struct usb_device: change flag to bitflag
  OHCI: make autostop conditional on CONFIG_PM
  USB: Add autosuspend support to the hub driver
  EHCI: Fix root-hub and port suspend/resume problems
  USB: create a new thread for every USB device found during the probe sequence
  USB: add driver for the USB debug devices
  USB: added dynamic major number for USB endpoints
  USB: pegasus error path not resetting task's state
  USB: endianness fix for asix.c
  USB: build the appledisplay driver
  USB serial: replace kmalloc+memset with kzalloc
  USB: hid-core: canonical defines for Apple USB device IDs
  USB: idmouse cleanup
  USB: make drivers/usb/core/driver.c:usb_device_match() static
  USB: lh7a40x_udc remove double declaration
  USB: pxa2xx_udc recognizes ixp425 rev b0 chip
  usbtouchscreen: add support for DMC TSC-10/25 devices
  ...