* switched to sane allocation
	* fixes race on removal - we unregistered too late
	* contrary to the comment, device had no destructor, so removal
had leaked - unregister_netdev() doesn't trigger freeing in that driver.
	* fixes freeing (kfree -> free_netdev)

Otherwise the same story as with previous patch - irda-related part of NE*
that got lost.

into redhat.com:/spare/repo/net-drivers-2.5

into redhat.com:/spare/repo/net-drivers-2.5

into redhat.com:/spare/repo/net-drivers-2.5

	* fixes leaks on failed init
	* switches to sane allocation
	* fixes netdev freeing (kfree -> free_netdev)
	* fixes the idiocy with ->init() (from registger_netdev()) calling
unregister_netdevice() in case of failure - before we got anywhere past
the very beginning of register_netdev().

That's a part of NE* series that failed through the cracks (there were
pending irda patches, so that had been postponed, irda patches either
hadn't materialized in two months or hadn't touched that driver at all,
the latter being more likely).

Please, apply.

--Boundary-00=_EQjNA7alc3Y2zQJ
Content-Type: text/plain;
  charset="iso-8859-1"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

Hi,

> Please resend patches that may be applied with "patch -p1",
> not "patch -p0".

ok., here's the first, suspend/resume

--Boundary-00=_EQjNA7alc3Y2zQJ
Content-Type: text/x-diff;
  charset="iso-8859-1";
  name="xircom_tulip_cb_pm.diff"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
	filename="xircom_tulip_cb_pm.diff"

From: Geert Uytterhoeven <geert@linux-m68k.org>

Hydra Ethernet: Convert to the new driver model

From: Geert Uytterhoeven <geert@linux-m68k.org>

Ariadne Ethernet: Convert to the new driver model

From: Geert Uytterhoeven <geert@linux-m68k.org>

A2065 Ethernet: Convert to the new driver model

From: Geert Uytterhoeven <geert@linux-m68k.org>

Atari Pamsnet Ethernet: Kill warning

From: Geert Uytterhoeven <geert@linux-m68k.org>

sun3lance updates from Sam Creasey:
  - Pass the correct flags to request_irq()
  - Add debug code for transmitting packets

Here is a rediff'd version of the patch to fix shared irq handling in pcnet_cs
and generic 8390 drivers.

Error path (EISA) probe was using device before set.

# This is a BitKeeper generated patch for the following project:
# Project Name: Linux kernel tree
# This patch format is intended for GNU patch command version 2.5 or higher.
# This patch includes the following deltas:
#	           ChangeSet	1.1567  -> 1.1568
#	  drivers/net/dgrs.c	1.23    -> 1.24
#
# The following is the BitKeeper ChangeSet Log
# --------------------------------------------
# 04/02/19	shemminger@osdl.org	1.1568
# fix bug in eisa error path.
# --------------------------------------------
#

* define dump stats complete constant
* add mwb() to keep order straight with HW when appending
  new resources to Rx and Tx queues
* increment stats for rx_dropped and rx_over_errors

* driver not handling failures of register_netdev
  [Stephen Hemminger (shemminger@osdl.org)]

* For half duplex, the IEEE says collision retry count should
  be 15 not 16.  Would cause really slow transfers on some hubs
  (i.e NetGear DS108).

* msec_delay macro wouldn't delay at all if x < 10, and
  wouldn't delay enough for x = 10.  Not a concern for
  2.6 (HZ=1000) but is for 2.4 (HZ=100).

* Multiple reports of system lock-ups with the CSA patch, so
  let's disable fix for now until we can understand why this
  is causing the hangs.  It was first thought that only pre-
  productions systems would hang, but that's not true.

* Disable TSO as default setting until some hangs/resets caused
  with TSO enabled are root-caused.  TSO can still be manually
  enabled using ethtool -K.

* Bug fix: flow control high/low watermark settings not
  within Rx FIFO range: math error.

Small patch to clean up 3c359_micrcode.h, no other drivers in the kernel
come anywhere near the file and the #if is superflous.

Mike Phillips

Arrgh.  I sent the wrong diff file.  This one fixes the compile error I
introduced ;-(

Last change for a while.  This modifies the whitespace only.
consistent indentation, deletes trailing tabs, trailing spaces, etc.

This adds the ability to do a local loopback test for the adapter.  This
source was submitted by James Lewis <jklewis@us.ibm.com>.  Tested on PPC
and IA32 systems.

This patch adds support for PCI hot remove.  Tested on PPC64 boxes.
The driver has also been checked to comply with PCMCIA/cardbus remove
requirements, but as I don't have a PCMCIA card, it is untested.
If a PCMCIA card is removed, reads will return FFFF.  The FFFF will
cause all while loops to exit.

pcnet32 devices which do not contain an mii respond incorrectly to
ethtool commands.

Reported by VANDROVE@vc.cvut.cz and Thomas Munck Steenholdt.

If there are errors in the open routine, the driver does not correctly clean
up and free resources.

This also removes an unnecessary netif_wake_queue, correctly supports the
debug parameter, and updates the version and date.

This changes the driver to use ethtool_ops to be more modular.  There is a
net delta of just a one line between the two implementations, but permission
checking and copying to/from user space, etc. is all done in a consistent
manner by ethtool.c

This patch converts the driver to use netif_msg_* for printing messages.
Tested IA32.

This patch was originally sent by Jon Mason on Sat Jan 31.

"I created a patch that allows pcnet32 adapters sold in IBM RS/6000 systems
to be recognized in non-ppc computers.  The problem is that the Vendor ID
of this adapter is incorrect.  There is a ppc specific workaround to get
it working on that architecture (checkout
http://lxr.linux.no/source/arch/ppc/kernel/pci.c?a=ppc#L87
for the workaround), but it obviously won't fix the problem in non-ppc
architectures."

per-network-interface message logging standards for net drivers.

Written by Donald Becker.

Domen Puncer schrieb:
>
> Just some suggestions...
>
>> #define ELEMENTS_OF(X) (sizeof(X) / sizeof((X)[0]))
>
> Remove this define and s/ELEMENTS_OF/ARRAY_SIZE/g
>

There are more occurances of redundant ARRAY_SIZEs in the kernel. I will
keep that in mind!

>
>
>>@@ -847,7 +845,7 @@
>> static int allocate_buffers(struct strip *strip_info, int mtu)
>> {
>>        struct net_device *dev = strip_info->dev;
>>-       int sx_size = MAX(STRIP_ENCAP_SIZE(MAX_RECV_MTU), 4096);
>>+       int sx_size = max((int)STRIP_ENCAP_SIZE(MAX_RECV_MTU), 4096);
>
>
> max_t?

Changed that to max_t and min_t. A newbie queston: What should when be
preferred and why?

When !CONFIG_PROC_FS, I'm getting this warning:

drivers/net/wireless/strip.c:1169: warning: `strip_seq_fops' defined but not used

into ppc970.osdl.org:/home/torvalds/v2.5/linux

We can bomb out early, so don't poke any registers just in case.

	Sigh...  Build/fix bugs/rediff/send the old diff story...
Sorry - just have noticed that ;-/