- 14 Jul, 2020 17 commits
-
-
Wright Feng authored
Linux 3.6 introduces TSQ which has a per socket threshold for TCP Tx packet to reduce latency. In flow control mode, host driver enqueues skb in hanger and TCP doesn't push new skb frees until host frees the skb when receiving fwstatus event. So set pacing shift 8 to send them as a single large aggregate frame to the bus layer. 43455 TX TCP throughput in different FC modes on Linux 5.4.18 sk_pacing_shift : Throughput (fcmode=0) 10: 245 Mbps 9: 245 Mbps 8: 246 Mbps 7: 246 Mbps sk_pacing_shift : Throughput (fcmode=1) 10: 182 Mbps 9: 197 Mbps 8: 206 Mbps 7: 207 Mbps sk_pacing_shift : Throughput (fcmode=2) 10: 180 Mbps 9: 197 Mbps 8: 206 Mbps 7: 207 Mbps Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200624091608.25154-3-wright.feng@cypress.com
-
Wright Feng authored
When USB or SDIO device got abnormal bus disconnection, host driver tried to clean up the skbs in PSQ and TXQ (The skb's pointer in hanger slot linked to PSQ and TSQ), so we should set the state of skb hanger slot to BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb. In brcmf_fws_bus_txq_cleanup it already sets BRCMF_FWS_HANGER_ITEM_STATE_FREE before freeing skb, therefore we add the same thing in brcmf_fws_psq_flush to avoid following warning message. [ 1580.012880] ------------ [ cut here ]------------ [ 1580.017550] WARNING: CPU: 3 PID: 3065 at drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49 brcmu_pkt_buf_free_skb+0x21/0x30 [brcmutil] [ 1580.184017] Call Trace: [ 1580.186514] brcmf_fws_cleanup+0x14e/0x190 [brcmfmac] [ 1580.191594] brcmf_fws_del_interface+0x70/0x90 [brcmfmac] [ 1580.197029] brcmf_proto_bcdc_del_if+0xe/0x10 [brcmfmac] [ 1580.202418] brcmf_remove_interface+0x69/0x190 [brcmfmac] [ 1580.207888] brcmf_detach+0x90/0xe0 [brcmfmac] [ 1580.212385] brcmf_usb_disconnect+0x76/0xb0 [brcmfmac] [ 1580.217557] usb_unbind_interface+0x72/0x260 [ 1580.221857] device_release_driver_internal+0x141/0x200 [ 1580.227152] device_release_driver+0x12/0x20 [ 1580.231460] bus_remove_device+0xfd/0x170 [ 1580.235504] device_del+0x1d9/0x300 [ 1580.239041] usb_disable_device+0x9e/0x270 [ 1580.243160] usb_disconnect+0x94/0x270 [ 1580.246980] hub_event+0x76d/0x13b0 [ 1580.250499] process_one_work+0x144/0x360 [ 1580.254564] worker_thread+0x4d/0x3c0 [ 1580.258247] kthread+0x109/0x140 [ 1580.261515] ? rescuer_thread+0x340/0x340 [ 1580.265543] ? kthread_park+0x60/0x60 [ 1580.269237] ? SyS_exit_group+0x14/0x20 [ 1580.273118] ret_from_fork+0x25/0x30 [ 1580.300446] ------------ [ cut here ]------------ Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200624091608.25154-2-wright.feng@cypress.com
-
Chi-Hsien Lin authored
commit 4684997d ("brcmfmac: reset PCIe bus on a firmware crash") adds a reset function to recover firmware trap for PCIe bus. This commit adds an implementation for SDIO bus. Upon SDIO firmware trap, do below: - Remove the device - Reset hardware - Probe the device again Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200622144851.165248-1-chi-hsien.lin@cypress.com
-
Able Liao authored
Ignore FW event if the event's BSSID is different form the BSSID of the currently connected AP. Check interface state is connected or not, if state is not connected that can ignore link down event. Signed-off-by: Able Liao <Able.Liao@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200618160739.21457-4-chi-hsien.lin@cypress.com
-
Soontak Lee authored
Current brcmf_link_down() always call cfg80211_disconnected() with locally_generated=1, which is not always the case. Add event source argument on link down handler and set locally_generated based on the real trigger. Signed-off-by: Soontak Lee <soontak.lee@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200618160739.21457-3-chi-hsien.lin@cypress.com
-
Soontak Lee authored
Unable to change back to visiable SSID because there is no disable hidden ssid routine. Signed-off-by: Soontak Lee <soontak.lee@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200618160739.21457-2-chi-hsien.lin@cypress.com
-
Joseph Chuang authored
Commit 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg method") did not initialize requested_dwell properly, resulting in an always-false dwell time overflow check. Fix it by setting the correct requested_dwell value. Fixes: 4905432b28b7 ("brcmfmac: Fix P2P Group Formation failure via Go-neg method") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200610152106.175257-7-chi-hsien.lin@cypress.com
-
Double Lo authored
This patch move the credit map setting to right place to avoid brcmf_fws_return_credits() return without setting the credit map. It fix the thoughput zero stalls issue in softAP mode when STA using PM 1 mode. Signed-off-by: Double Lo <double.lo@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200610152106.175257-6-chi-hsien.lin@cypress.com
-
Chung-Hsien Hsu authored
There is a mismatch of tx status flag values between host and firmware. It makes the host mistake the flags and have incorrect behavior of credit returns. So update the flags to sync with the firmware ones. Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200610152106.175257-5-chi-hsien.lin@cypress.com
-
Amar Shankar authored
It is observed that sometimes when sdiod is low in tx credits in low rssi scenarios, the data path consumes all sdiod rx all credits and there is no sdiod rx credit available for control path causing host and card to go out of sync resulting in link loss between host and card. So in order to prevent it some credits are reserved for control path. Note that TXCTL_CREDITS can't be larger than the firmware default credit update threshold 2; otherwise there will be a deadlock for both side waiting for each other. Signed-off-by: Amar Shankar <amsr@cypress.com> Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200610152106.175257-4-chi-hsien.lin@cypress.com
-
Jia-Shyr Chuang authored
In wifi firmware, max length of IOCTL/IOVAR buffer size is 8192. Increase the message buffer max size same as wifi firmware for control packets so return buffers can come back. Signed-off-by: Soontak Lee <soontak.lee@cypress.com> Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200610152106.175257-3-chi-hsien.lin@cypress.com
-
Raveendran Somu authored
Current credit borrowing allows only the access category BE to borrow the credits. This change is to fix the credit borrowing logic, to make borrowing available for all access categories and also to borrow only from the lower categories. This fixes WFA 802.11n certs 5.2.27 failures. Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com> Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com> Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200610152106.175257-2-chi-hsien.lin@cypress.com
-
Prasanna Kerekoppa authored
Bss info flag definition need to be fixed from 0x2 to 0x4 This flag is for rssi info received on channel. All Firmware branches defined as 0x4 and this is bug in brcmfmac. Signed-off-by: Prasanna Kerekoppa <prasanna.kerekoppa@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200604071835.3842-6-wright.feng@cypress.com
-
Wright Feng authored
The firmware state machines are not fully suitable for concurrent station interface support, it may hit unexpected error if we have 2 different SSIDs and the roaming scenarios concurrently. To avoid the bad user-experience if this is not fully validated, we dis-allow user to create two concurrent station interfaces. Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200604071835.3842-5-wright.feng@cypress.com
-
Wright Feng authored
brcmfmac host driver makes SDIO bus sleep and stops SDIO watchdog if no pending event or data. As a result, host driver does not poll firmware console buffer before buffer overflow, which leads to missing firmware logs. We should not stop SDIO watchdog if console_interval is non-zero in debug build. Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200604071835.3842-4-wright.feng@cypress.com
-
Wright Feng authored
When host driver retrieves mac addresses from dongle, driver copies memory from drvr->mac to perm_addr. But at the moment, drvr->mac is all zero array which causes permanent MAC address in wiphy is all zero as well. To fix this, we set drvr->mac before setting perm_addr. Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200604071835.3842-3-wright.feng@cypress.com
-
Raveendran Somu authored
To truncate the additional bytes, if extra bytes have been received. Current code only have a warning and proceed without handling it. But in one of the crash reported by DVT, these causes the crash intermittently. So the processing is limit to the skb->len. Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com> Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200604071835.3842-2-wright.feng@cypress.com
-
- 02 Jul, 2020 1 commit
-
-
Kalle Valo authored
This is an immutable branch shared between wireless-drivers-next and staging-next for moving wilc1000 driver out of staging to drivers/net/wireless directory.
-
- 26 Jun, 2020 1 commit
-
-
Ajay Singh authored
WILC1000 is an IEEE 802.11 b/g/n IoT link controller module. The WILC1000 connects to Microchip AVR/SMART MCUs, SMART MPUs, and other processors with minimal resource requirements with a simple SPI/SDIO-to-Wi-Fi interface. WILC1000 driver has been part of staging for few years. With contributions from the community, it has improved significantly. Full driver review has helped in achieving the current state. The details for those reviews are captured in 1 & 2. [1]. https://lore.kernel.org/linux-wireless/1537957525-11467-1-git-send-email-ajay.kathat@microchip.com/ [2]. https://lore.kernel.org/linux-wireless/1562896697-8002-1-git-send-email-ajay.kathat@microchip.com/Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
- 15 Jun, 2020 8 commits
-
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2020-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next First set of patches intended for v5.9 * Fix links to wiki; * Some preparations for gcc-10; * Make FW reconfiguration quieter by not using warn level; * Some other small fixes and clean-up; # gpg: Signature made Thu 11 Jun 2020 12:03:51 PM EEST using RSA key ID 1A3CC5FA # gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>" # gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.9. Major changes: ath11k * add 6G band support * add spectral scan support
-
Venkateswara Naralasetty authored
Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd are set based on the rsnie and wpaie of the bss from the bss list. Since this bss list is not updated with current BSSID for AP mode, we may not find bss from the bss list. Which results in ptk/gtk peer flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames are going in data rates instead of management rates. Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
-
Sriram R authored
Add support for collecting and dumping the ring backpressure stats via debugfs. Stats are dumped only if events are received for the specific ring. Below command can be used to obtain these stats as part of soc dp stats. cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats Sample Output - When No stats available: Backpressure Stats ================== No Ring Backpressure stats received Sample Output - When ring bp stats available for specific ring Backpressure Stats ================== Ring: REO2SW1_RING count: 1 hp: 2 tp: 2 seen before: 4ms Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
-
Sriram R authored
Add support for dp tx error stats which logs tx failure reasons due to ring full condition, etc. This stats is added in soc_dp_stats which was earlier used as soc_rx_stats so that all dp related info are logged in same file. Below is an example usage, root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats SOC RX STATS: err ring pkts: 0 Invalid RBM: 0 <snip> SOC TX STATS: Ring Full Failures: ring0: 4 ring1: 3 ring2: 5 Misc Transmit Failures: 2 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
-
Sowmiya Sree Elavalagan authored
Removed reo cmd lock and unlock which was acquiring the lock immediately after unlock. Done for code clean up. Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1591713432-26426-1-git-send-email-ssreeela@codeaurora.org
-
Karthikeyan Periyasamy authored
spectral scan control interface is exposed through debugfs eentry. Relayfs is used to collect the spectral data. These interfaces are similar to ath10k spectral. spectral debugfs interfaces are below, echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl iw dev wlan0 scan echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
-
Karthikeyan Periyasamy authored
Add direct buffer ring (dbring) with helper API, which is used by the spectral scan. Initialise the direct buffer ring based on the dma ring capability, which get announced in the wmi service ready extended event. This ring is slightly changed from data path rings. Compare to data path ring this ring shares the hp and tp address to firmware though WMI commands. Also the replenish buffer size is derived from firmware announcement. driver receive indication through WMI event WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID. Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
-
- 14 Jun, 2020 4 commits
-
-
Linus Torvalds authored
-
git://github.com/micah-morton/linuxLinus Torvalds authored
Pull SafeSetID update from Micah Morton: "Add additional LSM hooks for SafeSetID SafeSetID is capable of making allow/deny decisions for set*uid calls on a system, and we want to add similar functionality for set*gid calls. The work to do that is not yet complete, so probably won't make it in for v5.8, but we are looking to get this simple patch in for v5.8 since we have it ready. We are planning on the rest of the work for extending the SafeSetID LSM being merged during the v5.9 merge window" * tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux: security: Add LSM hooks to set*gid syscalls
-
Thomas Cedeno authored
The SafeSetID LSM uses the security_task_fix_setuid hook to filter set*uid() syscalls according to its configured security policy. In preparation for adding analagous support in the LSM for set*gid() syscalls, we add the requisite hook here. Tested by putting print statements in the security_task_fix_setgid hook and seeing them get hit during kernel boot. Signed-off-by: Thomas Cedeno <thomascedeno@google.com> Signed-off-by: Micah Morton <mortonm@chromium.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs updates from David Sterba: "This reverts the direct io port to iomap infrastructure of btrfs merged in the first pull request. We found problems in invalidate page that don't seem to be fixable as regressions or without changing iomap code that would not affect other filesystems. There are four reverts in total, but three of them are followup cleanups needed to revert a43a67a2 cleanly. The result is the buffer head based implementation of direct io. Reverts are not great, but under current circumstances I don't see better options" * tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: Revert "btrfs: switch to iomap_dio_rw() for dio" Revert "fs: remove dio_end_io()" Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK" Revert "btrfs: split btrfs_direct_IO to read and write part"
-
- 13 Jun, 2020 9 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix cfg80211 deadlock, from Johannes Berg. 2) RXRPC fails to send norigications, from David Howells. 3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from Geliang Tang. 4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu. 5) The ucc_geth driver needs __netdev_watchdog_up exported, from Valentin Longchamp. 6) Fix hashtable memory leak in dccp, from Wang Hai. 7) Fix how nexthops are marked as FDB nexthops, from David Ahern. 8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni. 9) Fix crashes in tipc_disc_rcv(), from Tuong Lien. 10) Fix link speed reporting in iavf driver, from Brett Creeley. 11) When a channel is used for XSK and then reused again later for XSK, we forget to clear out the relevant data structures in mlx5 which causes all kinds of problems. Fix from Maxim Mikityanskiy. 12) Fix memory leak in genetlink, from Cong Wang. 13) Disallow sockmap attachments to UDP sockets, it simply won't work. From Lorenz Bauer. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits) net: ethernet: ti: ale: fix allmulti for nu type ale net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init net: atm: Remove the error message according to the atomic context bpf: Undo internal BPF_PROBE_MEM in BPF insns dump libbpf: Support pre-initializing .bss global variables tools/bpftool: Fix skeleton codegen bpf: Fix memlock accounting for sock_hash bpf: sockmap: Don't attach programs to UDP sockets bpf: tcp: Recv() should return 0 when the peer socket is closed ibmvnic: Flush existing work items before device removal genetlink: clean up family attributes allocations net: ipa: header pad field only valid for AP->modem endpoint net: ipa: program upper nibbles of sequencer type net: ipa: fix modem LAN RX endpoint id net: ipa: program metadata mask differently ionic: add pcie_print_link_status rxrpc: Fix race between incoming ACK parser and retransmitter net/mlx5: E-Switch, Fix some error pointer dereferences net/mlx5: Don't fail driver on failure to create debugfs net/mlx5e: CT: Fix ipv6 nat header rewrite actions ...
-
David Sterba authored
This reverts commit a43a67a2. This patch reverts the main part of switching direct io implementation to iomap infrastructure. There's a problem in invalidate page that couldn't be solved as regression in this development cycle. The problem occurs when buffered and direct io are mixed, and the ranges overlap. Although this is not recommended, filesystems implement measures or fallbacks to make it somehow work. In this case, fallback to buffered IO would be an option for btrfs (this already happens when direct io is done on compressed data), but the change would be needed in the iomap code, bringing new semantics to other filesystems. Another problem arises when again the buffered and direct ios are mixed, invalidation fails, then -EIO is set on the mapping and fsync will fail, though there's no real error. There have been discussions how to fix that, but revert seems to be the least intrusive option. Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/Signed-off-by: David Sterba <dsterba@suse.com>
-
Grygorii Strashko authored
On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow unregistered mcast packets to pass. This happens, because ALE VLAN entries on these SoCs do not contain port masks for reg/unreg mcast packets, but instead store indexes of ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for reg/unreg mcast packets. This path was missed by commit 9d1f6447 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled"). Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti(). Fixes: 9d1f6447 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
The ALE parameters structure is created on stack, so it has to be reset before passing to cpsw_ale_create() to avoid garbage values. Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Alexei Starovoitov says: ==================== pull-request: bpf 2020-06-12 The following pull-request contains BPF updates for your *net* tree. We've added 26 non-merge commits during the last 10 day(s) which contain a total of 27 files changed, 348 insertions(+), 93 deletions(-). The main changes are: 1) sock_hash accounting fix, from Andrey. 2) libbpf fix and probe_mem sanitizing, from Andrii. 3) sock_hash fixes, from Jakub. 4) devmap_val fix, from Jesper. 5) load_bytes_relative fix, from YiFei. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Liao Pingfang authored
Looking into the context (atomic!) and the error message should be dropped. Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull more cifs updates from Steve French: "12 cifs/smb3 fixes, 2 for stable. - add support for idsfromsid on create and chgrp/chown allowing ability to save owner information more naturally for some workloads - improve query info (getattr) when SMB3.1.1 posix extensions are negotiated by using new query info level" * tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: smb3: Add debug message for new file creation with idsfromsid mount option cifs: fix chown and chgrp when idsfromsid mount option enabled smb3: allow uid and gid owners to be set on create with idsfromsid mount option smb311: Add tracepoints for new compound posix query info smb311: add support for using info level for posix extensions query smb311: Add support for lookup with posix extensions query info smb311: Add support for SMB311 query info (non-compounded) SMB311: Add support for query info using posix extensions (level 100) smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl smb3: fix typo in mount options displayed in /proc/mounts cifs: Add get_security_type_str function to return sec type. smb3: extend fscache mount volume coherency check
-
Linus Torvalds authored
Let's keep "git status" happy and quiet. Fixes: 9762dc14 ("samples: add binderfs sample program Fixes: fca5e949 ("samples: binderfs: really compile this sample and fix build issues") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
I'm not convinced the script makes useful automaed help lines anyway, but since we're trying to deprecate the use of "---help---" in Kconfig files, let's fix the doc example code too. See commit a7f7f624 ("treewide: replace '---help---' in Kconfig files with 'help'") Cc: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-