- 04 Sep, 2018 31 commits
-
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Addresses-Coverity-ID: 1077614 ("Missing break in switch") Signed-off-by:Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Quentin Schulz authored
VSC8584 supports 4 LEDs while VSC8531 only supports 2. Let's factorize the documentation for LED mode properties and give the 4 default values (the first two being shared between VSC8531 and VSC8584). Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by:
-
Quentin Schulz authored
Compatible isn't a required property for PHYs so let's remove it from the binding DT of the VSC8531 PHYs. Acked-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Quentin Schulz authored
In the DT binding, it is specified nowhere that 'vsc8531,led-%d-mode' is an u8, even though it's read as an u8 in the driver. Let's update the driver to take into consideration that the 'vsc8531,led-%d-mode' property is of the default type u32. Signed-off-by:
-
Quentin Schulz authored
In the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown' is an u8, even though it's read as an u8 in the driver. Let's update the driver to take into consideration that the 'vsc8531,edge-slowdown' property is of the default type u32. Signed-off-by:
-
Quentin Schulz authored
In the DT binding, it is specified nowhere that 'vsc8531,vddmac' is an u16, even though it's read as an u16 in the driver. Let's update the driver to take into consideration that the 'vsc8531,vddmac' property is of the default type u32. Signed-off-by:
-
Quentin Schulz authored
Microsemi PHYs support different LED modes depending on the variant, so let's factorize the code so we just have to give the supported modes while the logic behind getting the mode remains identical. Signed-off-by:
-
Quentin Schulz authored
LEDs modes are set the same way, except they are offset by 4 times the index of the LED. Let's factorize all the code so that it's easier to add support for the 4 LEDs of the VSC8584 PHY. Signed-off-by:
-
David S. Miller authored
David Gounaris says: ==================== Ethernet over hdlc ==================== Signed-off-by: -
David Gounaris authored
Added tx timeout handler. This helps when troubleshooting. Signed-off-by:
David Gounaris <david.gounaris@infinera.com> Signed-off-by:
-
David Gounaris authored
The following bits in the GUMR is changed for non tsa mode: CDS, CTSP and CTSS are set to zero. When set, there is no tx interrupts from the controller. Signed-off-by:
-
David Gounaris authored
Ability to set hmask in the device-tree, which can be used to change address filtering of packets. Signed-off-by:
-
David Gounaris authored
This patch is to avoid discarding ethernet packets when using HDLC_ETH protocol. Signed-off-by:
-
David Gounaris authored
Signed-off-by:
-
David Gounaris authored
There is a need to allow higher indexes to be able to support MPC83xx platforms. (UCC1-UCC8) Signed-off-by:
-
Rahul Lakkireddy authored
Collect descriptors of all ULD and LLD hardware queues managed by LLD. Signed-off-by:
Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
-
Ganesh Goudar authored
in ndo_set_vf_rate() when max_tx_rate is 0 disable tx rate limiting for that vf. Signed-off-by:
Casey Leedom <leedom@chelsio.com> Signed-off-by:
-
David S. Miller authored
Salil Mehta says: ==================== Misc. bug fixes & small enhancements for HNS3 Driver This patch-set presents some fixes and minor enhancements to HNS3 Driver ==================== Signed-off-by: -
Jian Shen authored
In the previous implement, the query operation for fibre port and copper port are mixed. This patch refines it by seperating them based on the port type. Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
-
Jian Shen authored
If the advertised flow control ability has been fetched using phy_ethtool_ksettings_get() or hclge_get_link_mode() then it is unnecessary to fetch them again later using hclge_get_flowctrl_adv(). This patch removes it. Signed-off-by:
-
Yunsheng Lin authored
Currently, the dst mac addr of loopback packet is the same as the host' mac addr, the SSU component may loop back the packet to host before the packet reaches mac or serdes, which will defect the purpose of mac or serdes selftest. This patch changes it by adding 0x1f to the last byte of dst mac addr. Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
Currently only fiber port checks if it is necessay to set the mac through firmware when link is changed, this patch unify the checking to allow the copper port do the checking too. Signed-off-by:
-
Yunsheng Lin authored
When netdev is down, the stack will delete the vlan from hardware including vlan0, which will cause problem when doing loopback selftest when netdev is down. This patch fixes it by always preserving vlan 0 in hardware, because vlan 0 is defalut vlan, which should always be in hardware. Fixes: c39c4d98 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by:
-
Yunsheng Lin authored
When ping is runnig and user executes the loopback selftest, the ping cmd will stop and exit. This patch fixes it by using the hns3_nic_net_open/stop to offline the netdev when doing loopback selftest. Fixes: c39c4d98 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by:
-
Yunsheng Lin authored
Tqp and mac need to be enabled when doing loopback selftest, ae_algo->ops->start/stop is used to do the job, there is a time window between ae_algo->ops->start/stop and loopback setup, which will cause selftest failed problem when there is frame coming in during that time window. This patch fixes it by enabling the tqp and mac during loopback setup process. Fixes: c39c4d98 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by:
-
Yunsheng Lin authored
This patch implements shutdown ops in hns3 pci driver, which unloads the hns3 driver and set the power state to D3hot. Signed-off-by:
-
Jian Shen authored
PF uses hdev->vlan_table to manage the port vlan table. In function hclge_set_vlan_filter_hw(), it checks whether a vlan id has been used, by foreach all the vport bits. It should use macro HCLGE_VPORT_NUM, not VLAN_N_VID as the foreach condition. Fixes: 6c251711 ("net: hns3: Disable vf vlan filter when vf vlan table is full") Signed-off-by:
-
Huazhong Tan authored
When the lower 24 bits of the IPV6 link-local addresses at both ends are the same, the multicast MAC address for Neigbour Discovery is the same. The multicast for Neigbour Discovery will fail. This patch fixes it by including the bonding uplink port in the multicast group. Fixes: 46a3df9f("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Yunsheng Lin authored
There are only 128 entries in vf vlan table, if user has added more than 128 vlan, fw will ignore it and disable the vf vlan table. So when user deletes the vlan entry that has not been set to vf vlan table, fw will return not found result and driver treat that as error, which will cause vlan delete failed problem. This patch fixes it by returning ok when fw returns not found result. Fixes: 6c251711 ("net: hns3: Disable vf vlan filter when vf vlan table is full") Signed-off-by:
-
Zhenbo Gao authored
Remove the following obsolete parameter comments of tipc_topsrv struct: @rcvbuf_cache @tipc_conn_new @tipc_conn_release @tipc_conn_recvmsg @imp @type Add the comments for the missing parameters below of tipc_topsrv struct: @awork @listener Remove the unused or duplicated parameter comments of tipc_conn struct: @outqueue_lock @rx_action Signed-off-by:
Zhenbo Gao <zhenbo.gao@windriver.com> Reviewed-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Pradeep Nalla authored
Signed-off-by:
Pradeep Nalla <pradeep.nalla@cavium.com> Signed-off-by:
Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by:
-
- 02 Sep, 2018 9 commits
-
-
David S. Miller authored
Tariq Toukan says: ==================== mlx5e IPoIB stats This patchset by Feras contains statistics enhancements and NDO implementation for the mlx5e IPoIB driver. Series generated against net-next commit: 2d5c2885 net: bgmac: remove set but not used variable 'err' ==================== Signed-off-by:
-
Feras Daoud authored
Since the RQs are shared between all pkey interfaces, the stats should be taken from where the per-ring stats are stored instead of the parent RQ. Fixes: 4c6c615e ("net/mlx5e: IPoIB, Add PKEY child interface nic profile") Signed-off-by:
Feras Daoud <ferasda@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Feras Daoud authored
Expose RX and TX counters by implementing ndo_get_stats64 operation for child devices. Signed-off-by:
-
Feras Daoud authored
Expose RX and TX counters by implementing ndo_get_stats64 operation for both parent devices. After this change, all the relevant statistics can be retrieved using ifconfig. Signed-off-by:
-
Feras Daoud authored
Enhanced ipoib does not initialize max_opened_tc causing wrong ethtool statistics. As mlx5e_grp_sw_update_stats relies on this variable, without this change, the TX statistics will not be updated. Fixes: 05909bab ("net/mlx5e: Avoid reset netdev stats on configuration changes") Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== Full phylink support for mv88e6352 These two patches implement full phylink support for the mv88e6352 family, when using an SFP connected to its SERDES interface. This adds interrupt support to the SERDES, so that we get interrupts on link up/down, and then make calls phydev_link_change(). The first patch is a minor bug fix, which does not seem to affect any current features, so i'm not submitting it for stable. It is however required for configuring SERDES interrupts. ==================== Signed-off-by: -
Andrew Lunn authored
The 6352 family has one SERDES interface, which can be used by either port 4 or port 5. Add interrupt support for the SERDES interface, and report when the link status changes. Signed-off-by:
-
Andrew Lunn authored
After changing to the needed page, actually write the value to the register! Fixes: 09cb7dfd ("net: dsa: mv88e6xxx: describe PHY page and SerDes") Signed-off-by:
-
Yafang Shao authored
cp_hashinfo.ehash_mask is always an odd number, which is set in function alloc_large_system_hash(). See bellow, if (_hash_mask) *_hash_mask = (1 << log2qty) - 1; <<< always odd number Hence the local variable 'cnt' is a even number, as a result of that it is no difference to do the incrementation here. Signed-off-by:Yafang Shao <laoar.shao@gmail.com> Signed-off-by:
-
