Add mt8173 support using mediatek common pinctrl driver.
MT8173 have a different ies_smt setting register than mt8135,
so adding this support to common code.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

MTK SoC support external interrupt(EINT) from most SoC pins.
Add EINT support to pinctrl driver.
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.

The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.

This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add devicetree bindings for Mediatek SoC pinctrl driver.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

As PFC registers are either 8, 16, or 32 bits wide, use u32 (mostly
replacing unsigned long) to store (parts of) register values and masks.

Switch the shadow register operations from {set,clear}_bit() to plain C
bit operations, as the former can operate on long data only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the initial driver support for the Broadcom Cygnus IOMUX
controller. The Cygnus IOMUX controller supports group based mux
configuration but allows certain pins to be muxed to GPIO individually
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Device tree binding documentation for Broadcom Cygnus IOMUX driver
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Consolidate Broadcom pinctrl drivers into drivers/pinctrl/bcm/*
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit 3dac1918 ("pinctrl: imx: detect uninitialized pins") needs
the values in struct imx_pin_reg to be -1. This has been done in a
rather unorthodox way by setting the memory to 0xff using memset...
Use a proper for loop to initialize the whole array with -1.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This enables support of 'input-enable' pinconf generic property in
the pinctrl driver.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the pinctrl driver to use the generic pinconf
interface. Mainly it gives us a way to use debugfs to dump
group configurations.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There is no code ender the 'err' label. Just return the error code directly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

struct pinctrl_desc does not contain the maxpin member since commit 0d2006bb
(pinctrl: remove unnecessary max pin number).

Fixes: 0d2006bb ('pinctrl: remove unnecessary max pin number')
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix typo, "flaged" -> "flagged"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).

Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Both nvidia,io-hv and nvidia,rcv-sel represent the fact that a particular
pin's IO buffers are configured to accept "high voltage" input signals.
The TRM for different chips names the register field rcv-sel on older
SoCs and io_hv on newer SoCs. Add the new naming option into the pinctrl
driver so that DT files can use naming consistent with the TRM.

This new property name will be documented in the patch that adds support
for the new SoC.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some of the pinmux configuration bits that exist in "drive group"
registers in Tegra30..Tegra124 move to the "pinmux" registers on future
chips. Add a flag to support this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Various non-semantic tweaks and layout/consistency fixes for existing
Tegra pinctrl drivers.

Move the definition of DRV_PINGROUP_REG() before the definition of
PINGROUP() so that a future SoC driver can invoke the former from the
latter.

PINGROUP_BIT_Y(n) is just n, so replace it with n.

Re-wrap the parameters to *PINGROUP().

Keep various enums sorted in the Tegra124 driver.

Various white-space consistency fixes.

These changes aim to update existing drivers to be consistent with future
SoC drivers. While we could ignore these tweaks to the existing drivers,
I'd like to keep everything as consistent as possible for easy comparison.
Besides, I auto-generate the drivers, and maintaining special-cases to
keep the differences in place is annoying.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This commit adds the Device Tree binding documentation to describe the
pin-muxing controller of the Marvell Armada 39x processors. Two
variants are supported for the moment: the 88F6920 (Armada 390) and
88F6928 (Armada 398).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make of_device_id array const.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

After the last user of the in_pd/in_pu bias parameters of the _PCRH()
macro was removed in commit 80da8e02 ("sh-pfc: r8a7740: Add bias
(pull-up/down) pinconf support"), bias parameters are supposed to be
configured using the generic pinctl mechanism, which calls the
.set_bias() method.

However, the PORTCR() macro still represents the control register as
consisting of two 4-bit fields. Hence the bias configuration in the
uppermost 2 bits is always overwritten with zeroes when a pin is
configured for GPIO, disabling any previously configured bias.

Use the variable config register macro instead, to represent the
register as having 4 fields, and to make sure only the input/output
control and function fields are touched.

This affects R-Mobile APE6 (r8a73a4), R-Mobile A1 (r8a7740), SH-Mobile
AP4 (sh7372), and SH-Mobile AG5 (sh73a0).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The r8a7791 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds driver data for Exynos5433 SoC. Exynos5433 includes 228 multi-
functional input/output port pins and 135 memory port pins. There are 41 general
port groups and 2 memory port groups.

Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This commit adds a new pinctrl driver for the Marvell Armada 39x
family of processors, which hooks into the existing infrastructure to
support pin-muxing on Marvell EBU processors. Two variants of the
Armada 39x are supported: 88F6920 (Armada 390) and 88F6928 (Armada
398), which have a few differences in the available functions for
certain pins.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

.. after extensive statistical analysis of my G+ polling, I've come to
the inescapable conclusion that internet polls are bad.

Big surprise.

But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38%
margin, in a poll that people weren't even supposed to participate in.
Who can argue with solid numbers like that? 5,796 votes from people who
can't even follow the most basic directions?

In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%,
but with a total of 29,110 votes right now.

Now, arguably, that vote spread is only about 3,200 votes, which is less
than the almost six thousand votes that the "please ignore" poll got, so
it could be considered noise.

But hey, I asked, so I'll honor the votes.

Pull ext4 fixes from Ted Ts'o:
 "Ext4 bug fixes.

  We also reserved code points for encryption and read-only images (for
  which the implementation is mostly just the reserved code point for a
  read-only feature :-)"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix indirect punch hole corruption
  ext4: ignore journal checksum on remount; don't fail
  ext4: remove duplicate remount check for JOURNAL_CHECKSUM change
  ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize
  ext4: support read-only images
  ext4: change to use setup_timer() instead of init_timer()
  ext4: reserve codepoints used by the ext4 encryption feature
  jbd2: complain about descriptor block checksum errors

Pull more vfs updates from Al Viro:
 "Assorted stuff from this cycle.  The big ones here are multilayer
  overlayfs from Miklos and beginning of sorting ->d_inode accesses out
  from David"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
  autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
  procfs: fix race between symlink removals and traversals
  debugfs: leave freeing a symlink body until inode eviction
  Documentation/filesystems/Locking: ->get_sb() is long gone
  trylock_super(): replacement for grab_super_passive()
  fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
  Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
  VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
  SELinux: Use d_is_positive() rather than testing dentry->d_inode
  Smack: Use d_is_positive() rather than testing dentry->d_inode
  TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
  Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
  Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
  VFS: Split DCACHE_FILE_TYPE into regular and special types
  VFS: Add a fallthrough flag for marking virtual dentries
  VFS: Add a whiteout dentry type
  VFS: Introduce inode-getting helpers for layered/unioned fs environments
  Infiniband: Fix potential NULL d_inode dereference
  posix_acl: fix reference leaks in posix_acl_create
  autofs4: Wrong format for printing dentry
  ...

Pull ARM fix from Russell King:
 "Just one fix this time around.  __iommu_alloc_buffer() can cause a
  BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or
  __GFP_HIGHMEM set.  The patch from Alexandre addresses this"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()

X-Coverup: just ask spender
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

use_pde()/unuse_pde() in ->follow_link()/->put_link() resp.

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.

And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...

Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

I've noticed significant locking contention in memory reclaimer around
sb_lock inside grab_super_passive(). Grab_super_passive() is called from
two places: in icache/dcache shrinkers (function super_cache_scan) and
from writeback (function __writeback_inodes_wb). Both are required for
progress in memory allocator.

Grab_super_passive() acquires sb_lock to increment sb->s_count and check
sb->s_instances. It seems sb->s_umount locked for read is enough here:
super-block deactivation always runs under sb->s_umount locked for write.
Protecting super-block itself isn't a problem: in super_cache_scan() sb
is protected by shrinker_rwsem: it cannot be freed if its slab shrinkers
are still active. Inside writeback super-block comes from inode from bdi
writeback list under wb->list_lock.

This patch removes locking sb_lock and checks s_instances under s_umount:
generic_shutdown_super() unlinks it under sb->s_umount locked for write.
New variant is called trylock_super() and since it only locks semaphore,
callers must call up_read(&sb->s_umount) instead of drop_super(sb) when
they're done.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fanotify probably doesn't want to watch autodirs so make it use d_can_lookup()
rather than d_is_dir() when checking a dir watch and give an error on fake
directories.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fix up the following scripted S_ISDIR/S_ISREG/S_ISLNK conversions (or lack
thereof) in cachefiles:

 (1) Cachefiles mostly wants to use d_can_lookup() rather than d_is_dir() as
     it doesn't want to deal with automounts in its cache.

 (2) Coccinelle didn't find S_IS* expressions in ASSERT() statements in
     cachefiles.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Convert the following where appropriate:

 (1) S_ISLNK(dentry->d_inode) to d_is_symlink(dentry).

 (2) S_ISREG(dentry->d_inode) to d_is_reg(dentry).

 (3) S_ISDIR(dentry->d_inode) to d_is_dir(dentry).  This is actually more
     complicated than it appears as some calls should be converted to
     d_can_lookup() instead.  The difference is whether the directory in
     question is a real dir with a ->lookup op or whether it's a fake dir with
     a ->d_automount op.

In some circumstances, we can subsume checks for dentry->d_inode not being
NULL into this, provided we the code isn't in a filesystem that expects
d_inode to be NULL if the dirent really *is* negative (ie. if we're going to
use d_inode() rather than d_backing_inode() to get the inode pointer).

Note that the dentry type field may be set to something other than
DCACHE_MISS_TYPE when d_inode is NULL in the case of unionmount, where the VFS
manages the fall-through from a negative dentry to a lower layer.  In such a
case, the dentry type of the negative union dentry is set to the same as the
type of the lower dentry.

However, if you know d_inode is not NULL at the call site, then you can use
the d_is_xxx() functions even in a filesystem.

There is one further complication: a 0,0 chardev dentry may be labelled
DCACHE_WHITEOUT_TYPE rather than DCACHE_SPECIAL_TYPE.  Strictly, this was
intended for special directory entry types that don't have attached inodes.

The following perl+coccinelle script was used:

use strict;

my @callers;
open($fd, 'git grep -l \'S_IS[A-Z].*->d_inode\' |') ||
    die "Can't grep for S_ISDIR and co. callers";
@callers = <$fd>;
close($fd);
unless (@callers) {
    print "No matches\n";
    exit(0);
}

my @cocci = (
    '@@',
    'expression E;',
    '@@',
    '',
    '- S_ISLNK(E->d_inode->i_mode)',
    '+ d_is_symlink(E)',
    '',
    '@@',
    'expression E;',
    '@@',
    '',
    '- S_ISDIR(E->d_inode->i_mode)',
    '+ d_is_dir(E)',
    '',
    '@@',
    'expression E;',
    '@@',
    '',
    '- S_ISREG(E->d_inode->i_mode)',
    '+ d_is_reg(E)' );

my $coccifile = "tmp.sp.cocci";
open($fd, ">$coccifile") || die $coccifile;
print($fd "$_\n") || die $coccifile foreach (@cocci);
close($fd);

foreach my $file (@callers) {
    chomp $file;
    print "Processing ", $file, "\n";
    system("spatch", "--sp-file", $coccifile, $file, "--in-place", "--no-show-diff") == 0 ||
	die "spatch failed";
}

[AV: overlayfs parts skipped]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use d_is_positive() rather than testing dentry->d_inode in SELinux to get rid
of direct references to d_inode outside of the VFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use d_is_positive() rather than testing dentry->d_inode in Smack to get rid of
direct references to d_inode outside of the VFS.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use d_is_dir() rather than d_inode and S_ISDIR().  Note that this will include
fake directories such as automount triggers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>