This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.

Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.

More information (in Japanese) available at:

	http://www.cente.jp/product/cente_hard/ESPT-Giga.htmlSigned-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Follow the PVR2 DMAC change for G2 DMA.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

When SuperH CPU has IRQ multi of DMAC, SH_DMA_IRQ_MULTI becomes enable.
The following CPU's are Multi IRQ of DMAC now.
 - SH775X and SH7091
 - SH776X
 - SH7780
 - SH7785

If SH_DMA_IRQ_MULTI becomes enable, dma-sh api driver is optimized
for Multi IRQ.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds suspend/resume support to the LCDC
driver for SuperH Mobile - sh_mobile_lcdcfb.

We simply stop hardware on suspend and start it again
on resume. For RGB panels this is trivial, but for SYS
panels in deferred io mode this becomes a bit more
difficult - we need to wait for a frame end interrupt
to make sure the clocks are balanced before stopping
the actual hardware.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.

To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

-- log --
arch/sh/kernel/cpu/sh4/../sh3/entry.S:365: Error: invalid operands for opcode
make[4]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
make[3]: *** [arch/sh/kernel/cpu/sh4] Error 2
-- log --
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

dma-sh's get_dma_error_irq() is only used by SH4, as the SH3
doesn't have the DMA Error interrupt.

Disable it out for non-SH4 builds.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This implements preliminary suspend/resume support for the PMB.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.

This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch changes sh_keysc to use to_platform_device()
for suspend. Thanks to Trilok Soni for this suggestion.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds support for the Sega Dreamcast visual memory unit as a
flash mapping. It requires changes in the maple bus driver (posted
separately) to support block reads and writes.

The VMU is a 'smart' flash device, with a built-in 8-bit controller -
for instance there is an erase before a write but it is hidden from the
user. But the device's overall behaviour means it works well with the
mtd layer and it is appropriate to add it as an mtd mapping.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.

This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Fix the problem that cannot work a PCI device when 32-bit physical
address mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.

P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds wakeup support to the sh_keysc driver.
With this feature the ".../power/wakeup" file can be
used to enable and disable if the device takes the
system out of suspend. Default is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Fix deferred io cleanup patch in the sh_mobile_lcdcfb driver.

If probe() fails early the sh_mobile_lcdc_stop() function will
be called to clean up deferred io. This patch modifies the
code to only call fb_deferred_io_cleanup() after deferred io
has been initialized.

With this patch applied we no longer hit BUG_ON() inside
fb_deferred_io_cleanup(). Triggers on a Migo-R with the
SYS QVGA panel board unmounted.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.

To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.

The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.

Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Add p4-clockmod sysfs-ui removal to feature-removal schedule.
  Revert "[CPUFREQ] Disable sysfs ui for p4-clockmod."

CLONE_PARENT can fool the ->self_exec_id/parent_exec_id logic. If we
re-use the old parent, we must also re-use ->parent_exec_id to make
sure exit_notify() sees the right ->xxx_exec_id's when the CLONE_PARENT'ed
task exits.

Also, move down the "p->parent_exec_id = p->self_exec_id" thing, to place
two different cases together.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>

This reverts commit e088e4c9.

Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.

Course of action:
 - Find out the remaining causes of overheating, and fix them
   if possible. ACPI should be doing the right thing automatically.
   If it isn't, we need to fix that.
 - mark p4-clockmod ui as deprecated
 - try again with the removal in six months.

It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
Signed-off-by: Dave Jones <davej@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
  p54: fix race condition in memory management
  cfg80211: test before subtraction on unsigned
  iwlwifi: fix error flow in iwl*_pci_probe
  rt2x00 : more devices to rt73usb.c
  rt2x00 : more devices to rt2500usb.c
  bonding: Fix device passed into ->ndo_neigh_setup().
  vlan: Fix vlan-in-vlan crashes.
  net: Fix missing dev->neigh_setup in register_netdevice().
  tmspci: fix request_irq race
  pkt_sched: act_police: Fix a rate estimator test.
  tg3: Fix 5906 link problems
  SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
  IPv6: add "disable" module parameter support to ipv6.ko
  sungem: another error printed one too early
  aoe: error printed 1 too early
  net pcmcia: worklimit reaches -1
  net: more timeouts that reach -1
  net: fix tokenring license
  dm9601: new vendor/product IDs
  netlink: invert error code in netlink_set_err()
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  lguest: fix for CONFIG_SPARSE_IRQ=y
  lguest: fix crash 'unhandled trap 13 at <native_read_msr_safe>'

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix spinlock assertions on UP systems

btrfs_tree_locked was being used to make sure a given extent_buffer was
properly locked in a few places.  But, it wasn't correct for UP compiled
kernels.

This switches it to using assert_spin_locked instead, and renames it to
btrfs_assert_tree_locked to better reflect how it was really being used.
Signed-off-by: Chris Mason <chris.mason@oracle.com>