- 25 Jun, 2007 1 commit
-
-
FUJITA Tomonori authored
The viosrp_crq timeout field is in seconds. Signed-off-by:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Santiago Leon <santil@us.ibm.com> Signed-off-by:
James Bottomley <James.Bottomley@SteelEye.com>
-
- 20 Jun, 2007 6 commits
-
-
Salyzyn, Mark authored
Support displaying long serial number information. Reuse sysfs handler internally as helper. Signed-off-by:
Mark Salyzyn <aacraid@adaptec.com> Signed-off-by:
-
Salyzyn, Mark authored
The Dell PERC2/QC erroneously was listed as having the 31 bit limit quirk on the interface allocations, removing the reference to repair this oversight. Also, the 2 quad pci address (family) match catch-all also retained the 31 bit limit and the 34 SG limit quirks in a paranoid move. Now, many years later, we find that none of the Adapters that did trigger with the family match had such quirks; these quirks are all limited to the 4 quad pci address matches to select legacy adapters already populated. Signed-off-by:
-
Salyzyn, Mark authored
This patch is more like a spelling correction than a fix. It was discovered that if we had a busy status return from the Adapter for the SCSI srb command to a physical component, that we returned DID_NO_CONNECT rather than what one would expect DID_BUS_BUSY. Signed-off-by:
-
Geert Uytterhoeven authored
- a4000t.c: Add missing include, needed in some configurations - bvme6000_scsi.c: Kill bogus opening brace - zorro7xx.c: Remove MODULE_DEVICE_TABLE, it should be part of another patch Signed-off-by:Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Guennadi Liakhovetski authored
Remove redundant defines from the header, replace all occurances in the code with standard SAM_STAT_ macros. Also fix what seems to be a typo in testing for (status == H_OVER_UNDER_RUN)... Signed-off-by:
G. Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Christof Schmitt authored
When reporting SCSI devices to the SCSI midlayer, use the FCP LUN as LUN reported to the SCSI layer. With this approach, zfcp does not have to create unique LUNS, and this code can be removed. Signed-off-by:
Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by:
Swen Schillig <swen@vnet.ibm.com> Signed-off-by:
-
- 19 Jun, 2007 2 commits
-
-
Volker Sameske authored
In some cases we did not reset some adapter status flags properly. This patch clears these flags during FCP adapter shutdown. Signed-off-by:
Volker Sameske <sameske@de.ibm.com> Signed-off-by:
-
FUJITA Tomonori authored
iscsi_iser: convert to use the data buffer accessors - remove the unnecessary map_single path. - convert to use the new accessors for the sg lists and the parameters. TODO: use scsi_for_each_sg(). Signed-off-by:
Erez Zilber <erezz@voltaire.com> Signed-off-by:
-
- 18 Jun, 2007 6 commits
-
-
James Smart authored
This patch updates the driver version to 8.2.1 Signed-off-by:
James Smart <James.Smart@emulex.com> Signed-off-by:
-
FUJITA Tomonori authored
This patch is a reworked version of the data buffer accessors patch so that it applies on the NPIV sources. The original patch was developed and submitted by Fujita Tomonori: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> http://marc.info/?l=linux-scsi&m=117896446832171&w=2 - remove the unnecessary map_single path. - convert to use the new accessors for the sg lists and the parameters. Signed-off-by: -
James Smart authored
Following the NPIV support, the following changes have been accumulated in the testing and qualification of the driver: - Fix affinity of ELS ring to slow/deferred event processing - Fix Ring attention masks - Defer dev_loss_tmo timeout handling to worker thread - Consolidate link down error classification for better error checking - Remove unused/deprecated nlp_initiator_tmr timer - Fix for async scan - move adapter init code back into pci_probe_one context. Fix async scan interfaces. - Expand validation of ability to create vports - Extract VPI resource cnt from firmware - Tuning of Login/Reject policies to better deal with overwhelmned targets - Misc ELS and discovery fixes - Export the npiv_enable attribute to sysfs - Mailbox handling fix - Add debugfs support - A few other small misc fixes: - wrong return values, double-frees, bad locking - Added adapter failure heartbeat Signed-off-by: -
James Smart authored
NPIV support is added to the driver. It utilizes the interfaces of the fc transport for the creation and deletion of vports. Within the driver, a new Scsi_Host is created for each NPIV instance, and is paired with a new instance of a FC port. This allows N FC Port elements to share a single Adapter. Signed-off-by:
-
James Smart authored
NPIV support is only available via new adapter interface extensions, termed SLI-3. This interface changes some of the basic behaviors such as command and response ring element sizes and data structures, as well as a change in buffer posting. Note: the new firmware extensions are found only on our mid-range and enterprise 4Gig adapters - so NPIV support is available only on these newer adapters. The latest firmware can be downloaded from the Emulex support page. Signed-off-by:
-
James Smart authored
The driver is reorganized to separate the handling of the adapter from the handling of the FC port. Adapter handling includes submissions of command requests, receiving responses, and managing adapter resources. The FC port includes the discovery engine, login handling, and the mapping of a Scsi_Host on the "port". Although not a large functional change, as it touches core structures and functions, resulting in a large text delta. Signed-off-by:
-
- 17 Jun, 2007 25 commits
-
-
FUJITA Tomonori authored
- convert to use the new accessors for the sg lists and the parameters. Signed-off-by:
-
FUJITA Tomonori authored
- remove the unnecessary map_single path. - convert to use the new accessors for the sg lists and the parameters. Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup. Signed-off-by:
HighPoint Linux Team <linux@highpoint-tech.com> Signed-off-by:
-
Kars de Jong authored
New driver for Amiga Zorro bus NCR53c710 SCSI controllers, using the 53c700 SCSI core. Signed-off-by:
-
Kars de Jong authored
New driver for the Amiga 4000T built-in NCR53c710 SCSI controller, using the 53c700 SCSI core. Signed-off-by:
-
Kars de Jong authored
New driver for the MVME16x NCR53C710 SCSI controller, using the 53c700 SCSI core. Signed-off-by:
-
Kars de Jong authored
New driver for the BVME6000 NCR53C710 SCSI controller, using the 53c700 SCSI core. Signed-off-by:
-
Kars de Jong authored
Add m68k support to the 53c700 SCSI driver Signed-off-by:
-
Eric Moore authored
If there is IO going to the volume while a hidden disk is being torn down, there is a case where we would return a DID_NO_CONNECT for IO sent to the volume. The end result is the volume goes read-only. This problem is due to the fact the firmware mapped target ids saved in per device object is phys_disk_num for hidden raid components, and target_id for the volume. There is a single case when both phys_disk_num and target_id are equal, so enters this issue. We fix this issue by checking the tflags when the device is torned down, insuring the IO being completed is meant for hidden raid component, not the volume. In addition to this fix, there are a couple other cases to address hidden raid components. For instance task_abort and device reset are not supported by mpt fw for hidden raid components, a bus reset would be required or target reset to volume. Signed-off-by:
Eric Moore <Eric.Moore@lsi.com> Signed-off-by:
-
Eric Moore authored
nice cosmetic cleaning of eh thread callback funtions Signed-off-by:
-
Alan Cox authored
I was investigating strange driver behaviour and thought that readable code and proper visible types might help explain why it didn't work right the moment a second SCB was outstanding to the controller. I was right - Cleanup, linuxise, demacro - Remove the BSD dual licence on the new work - Switch the if ALPHA to if __LP64__. (struct size is then right elsewhere) and then to CONFIG_64BIT as per Christoph's request - Fix the recursive locking on a reset. This is the only actual real code change (I hope ;)). I'm not clear what the right way to handle the BIOS param stuff is on n on x86-32/64. Using phys_to_virt and stuff is ugly and probably doesn't make sense elsewhere Still has a couple of odd things - and there seems to be a commonly shared EEPROM handling error several drivers have. Roughly speaking several SCSI drivers go try and read EEPROM It failed.. Write any changes between the default and the data we read Which is great as for some paths we've no idea what was in before, so each boot won't write it all back, won't checksum but will repeat the bug Also it can still sleep for a second with IRQ off, and there is some dubious looking error path locking marked FIXME in case anyone feels inspired to work on it. Not a newly introduced bug, and at least its now marked. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Hannes Reinecke authored
When a target scan is initiated from sysfs, we should check the portstate prior to invoke scsi_scan_target(). Otherwise scsi_scan_target() might oops as the rport might already been removed from the scsi host and the traversal from the rport to the scsi_host in scsi_scan_target() will fail. Also the portstate already told us that communication with the target has failed, so it's quite pointless to try. Signed-off-by:
Hannes Reinecke <hare@suse.de> Cc: James Smart <James.Smart@Emulex.Com> Signed-off-by:
-
FUJITA Tomonori authored
- remove the unnecessary map_single path. - convert to use the new accessors for the sg lists and the parameters. TODO: use scsi_for_each_sg(). Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Eric Moore authored
bump version Signed-off-by:
-
Eric Moore authored
rewrite of mpt_fc_log_info to use the enum/defines from mpi_log_fc.h Signed-off-by:
-
Eric Moore authored
remove unused header Signed-off-by:
-
Eric Moore authored
fc inband managment header deleted Signed-off-by:
-
Eric Moore authored
mpi header update Signed-off-by:
-
Eric Moore authored
Update assocated fusion sources with new support email address. Signed-off-by:
-
Brian King authored
Since it is completely possible for scsi core to call a LLDD's eh_abort function after the command has completed, fix ibmvscsi to return SUCCESS if this is the case. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Brian King authored
Fix a couple locking bugs discovered during code inspection. ibmvscsi_send_srp_event needs to be called with the host lock held. This patch fixes a couple paths in the code where this wasn't true. Signed-off-by:
-
Brian King authored
Adds an eh_host_reset_handler to ibmvscsi which resets the connection to the vscsi server. This patch also adds a timer to internally issues commands to prevent client hangs in the case of a misbehaving server. Tested by modifying the VIOS such that it would occasionally drop one or more request in sequence. Signed-off-by:
-
Brian King authored
Converts ibmvscsi to use dev_printk and friends to simplify debugging. ibmvscsi adapter initialization now looks like this: ibmvscsi 30000005: SRP_VERSION: 16.a ibmvscsi 30000005: partner initialization complete ibmvscsi 30000005: sent SRP login ibmvscsi 30000005: SRP_LOGIN succeeded Additionally, this patch adds the logging of a couple return codes in a couple logs. Signed-off-by:
-
Brian King authored
Since sg_tablesize is set appropriately in the scsi host template, remove the unnecessary check to make sure it is not exceeded following the dma_map_sg call. Signed-off-by:
-
FUJITA Tomonori authored
- remove the unnecessary map_single path. - convert to use the new accessors for the sg lists and the parameters. Note: needs to change i2o_dma_map_sg when the chaining sg is ready. Signed-off-by:
"Salyzyn, Mark" <mark_salyzyn@adaptec.com> Signed-off-by:
-
Salyzyn, Mark authored
Add the ability for an application to issue a hardware reset to the adapter via sysfs. Typical uses include restarting the adapter after it has been flashed. Bumped revision number for the driver and added a feature to periodically check the adapter's health (check_interval), update the adapter's concept of time (update_interval) and block checking/resetting of the adapter (check_reset). Signed-off-by:
-
