Improve g_tuner and add s_hw_freq_seek and enum_freq_bands support for cards
with TEA575x radio.

This allows signal/stereo detection and HW seek to work on these cards.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Split ioctl interface from enum_freq_bands, g_tuner and s_hw_freq_seek
functions and export them to be used in other drivers like bttv.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove tea575x-specific code from bttv and use the common driver instead.

Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).

It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).

Miro/Pinnacle is untested but seems to be simple and should work.

However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove the function pvr2_hdw_cmd_powerdown() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Removes some functions that are not used anywhere:
test_read() edid_read_block() dpp_write() dpp_read()
esdp_write() esdp_read() cec_write_clr_set()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove the function vsp1_hsit_read() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove the function saa7134_queue() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove the function write_eeprom_byte() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Removes some functions that are not used anywhere:
vblanking() hblanking()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>

The semantic patch also changes the cast to long to a cast to unsigned
long in the data initializer, as unsigned long is the type of the data field.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-t.function = f;
-t.data = d;
-init_timer(&t);
+setup_timer(&t,f,d);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

s/uint8_t/u8/
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

s/unsigned short/u16/
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

s/unsigned short/u16/
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

s/unsigned char/u8/
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The videobuf_dma_init* and videobuf_dma_map() functions are no longer
used except in videobuf-dma-sg.c itself. Make them static.

These functions were abused in various drivers. All those drivers
have now been fixed, so by no longer exporting these functions
future abuse is now prevented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove the function fm_rx_get_rds_system() that is not used anywhere.

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

this patch drops duplicate dependency of HAS_DMA from
VIDEO_SH_VEU.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

To be future-proof and for better readability the time comparisons are
modified to use time_after() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

As mx53 is a dt-only architecture we can safely remove its entry from the
coda_platform_ids[] structure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This is needed in order to get the media fixes applied on -rc6.

Linux 3.19-rc6

* tag 'v3.19-rc6': (891 commits)
  Linux 3.19-rc6
  dm: fix handling of multiple internal suspends
  hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
  hwmon: (i5500_temp) Convert to module_pci_driver
  hwmon: (i5500_temp) Don't bind to disabled sensors
  hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
  hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
  arm64: dts: add baud rate to Juno stdout-path
  Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
  Revert "Documentation: Add entry for dell-laptop sysfs interface"
  dm cache: fix problematic dual use of a single migration count variable
  dm cache: share cache-metadata object across inactive and active DM tables
  of/unittest: Overlays with sub-devices tests
  KVM: x86: SYSENTER emulation is broken
  KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
  arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
  x86/tsc: Change Fast TSC calibration failed from error to info
  x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
  x86, mm: Change cachemode exports to non-gpl
  x86, tls: Interpret an all-zero struct user_desc as "no segment"
  ...

Conflicts:
	drivers/media/pci/cx23885/cx23885.h

The debug parameter is not used anymore, as this module was
converted already to use dev_dbg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Increase si2168 cmd execute timeout to prevent firmware load failures. Tests
shows it takes up to 52ms to load the 'dvb-demod-si2168-a30-01.fw' firmware.
Increase timeout to a safe value of 70ms.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Pull x86 fixes from Thomas Gleixner:
 "Hopefully the last round of fixes for 3.19

   - regression fix for the LDT changes
   - regression fix for XEN interrupt handling caused by the APIC
     changes
   - regression fixes for the PAT changes
   - last minute fixes for new the MPX support
   - regression fix for 32bit UP
   - fix for a long standing relocation issue on 64bit tagged for stable
   - functional fix for the Hyper-V clocksource tagged for stable
   - downgrade of a pr_err which tends to confuse users

  Looks a bit on the large side, but almost half of it are valuable
  comments"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsc: Change Fast TSC calibration failed from error to info
  x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
  x86, mm: Change cachemode exports to non-gpl
  x86, tls: Interpret an all-zero struct user_desc as "no segment"
  x86, tls, ldt: Stop checking lm in LDT_empty
  x86, mpx: Strictly enforce empty prctl() args
  x86, mpx: Fix potential performance issue on unmaps
  x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
  x86, hyperv: Mark the Hyper-V clocksource as being continuous
  x86: Don't rely on VMWare emulating PAT MSR correctly
  x86, irq: Properly tag virtualization entry in /proc/interrupts
  x86, boot: Skip relocs when load address unchanged
  x86/xen: Override ACPI IRQ management callback __acpi_unregister_gsi
  ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()
  x86/xen: Treat SCI interrupt as normal GSI interrupt

Pull irq fixes from Thomas Gleixner:
 "From the irqchip departement you get:

   - regression fix for omap-intc

   - regression fix for atmel-aic-common

   - functional correctness fix for hip04

   - type mismatch fix for gic-v3-its

   - proper error pointer check for mtd-sysirq

  Mostly one and two liners except for the omap regression fix which is
  slightly larger than desired"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: atmel-aic-common: Prevent clobbering of priority when changing IRQ type
  irqchip: omap-intc: Fix legacy DMA regression
  irqchip: gic-v3-its: Fix use of max with decimal constant
  irqchip: hip04: Initialize hip04_cpu_map to 0xffff
  irqchip: mtk-sysirq: Use IS_ERR() instead of NULL pointer check

Pull timer fixes from Thomas Gleixner:
 "A set of small fixes:

   - regression fix for exynos_mct clocksource

   - trivial build fix for kona clocksource

   - functional one liner fix for the sh_tmu clocksource

   - two validation fixes to prevent (root only) data corruption in the
     kernel via settimeofday and adjtimex.  Tagged for stable"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: adjtimex: Validate the ADJ_FREQUENCY values
  time: settimeofday: Validate the values of tv from user
  clocksource: sh_tmu: Set cpu_possible_mask to fix SMP broadcast
  clocksource: kona: fix __iomem annotation
  clocksource: exynos_mct: Fix bitmask regression for exynos4_mct_write

Pull ARM SoC fixes from Olof Johansson:
 "A week's worth of fixes for various ARM platforms.  Diff wise, the
  largest fix is for OMAP to deal with how GIC now registers interrupts
  (irq_domain_add_legacy() -> irq_domain_add_linear() changes).

  Besides this, a few more renesas platforms needed the GIC instatiation
  done for legacy boards.  There's also a fix that disables coherency of
  mvebu due to issues, and a few other smaller fixes"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: add baud rate to Juno stdout-path
  ARM: dts: imx25: Fix PWM "per" clocks
  bus: mvebu-mbus: fix support of MBus window 13
  Merge tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu into fixes
  ARM: mvebu: completely disable hardware I/O coherency
  ARM: OMAP: Work around hardcoded interrupts
  ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
  ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
  arm: boot: dts: dra7: enable dwc3 suspend PHY quirk

Pull vfs fixes from Al Viro:
 "A couple of fixes - deadlock in CIFS and build breakage in cris serial
  driver (resurfaced f_dentry in there)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  VFS: Convert file->f_dentry->d_inode to file_inode()
  fix deadlock in cifs_ioctl_clone()

Pull device mapper fixes from Mike Snitzer:
 "Two stable fixes for dm-cache and one 3.19 DM core fix:

   - fix potential for dm-cache metadata corruption via stale metadata
     buffers being used when switching an inactive cache table to
     active; this could occur due to each table having it's own bufio
     client rather than sharing the client between tables.

   - fix dm-cache target to properly account for discard IO while
     suspending otherwise IO quiescing could complete prematurely.

   - fix DM core's handling of multiple internal suspends by maintaining
     an 'internal_suspend_count' and only resuming the device when this
     count drops to zero"

* tag 'dm-3.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix handling of multiple internal suspends
  dm cache: fix problematic dual use of a single migration count variable
  dm cache: share cache-metadata object across inactive and active DM tables

Pull two block layer fixes from Jens Axboe:
 "Two small patches that should make it into 3.19:

   - a fixup from me for NVMe, making the cq_vector a signed variable.
     Otherwise our -1 comparison fails, and commit 2b25d981 doesn't
     do what it was supposed to.

   - a fixup for the hotplug handling for blk-mq from Ming Lei, using
     the proper kobject referencing to ensure we release resources at
     the right time"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: fix hctx/ctx kobject use-after-free
  NVMe: cq_vector should be signed

pULL SCSI fixes from James Bottomley:
 "This consists of four real fixes and three MAINTAINER updates.

  Three of the fixes are obvious (the DIX and atomic allocation are bug
  on and warn on fixes and the other is just trivial) and the ipr one is
  a bit more involved but is required because without it, the card
  double completes aborted commands and causes a kernel oops"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  MAINTAINERS: ibmvscsi driver maintainer change
  MAINTAINERS: ibmvfc driver maintainer change
  MAINTAINERS: Remove self as isci maintainer
  scsi_debug: test always evaluates to false, || should be used instead
  scsi: Avoid crashing if device uses DIX but adapter does not support it
  scsi_debug: use atomic allocation in resp_rsup_opcodes
  ipr: wait for aborted command responses

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix reboot issues with the imx2_wdt driver and it also drops
  some forgotten owner assignments from platform_drivers"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: drop owner assignment from platform_drivers
  watchdog: imx2_wdt: Disable power down counter on boot
  watchdog: imx2_wdt: Improve power management support.

Pull hwmon update from Jean Delvare:
 "This contains a single thing: a new driver for the temperature sensor
  embedded in the Intel 5500/5520/X58 chipsets.

  Sorry for the late request, it's been so long since I last sent a pull
  request and I've been so busy with other tasks meanwhile that I simply
  forgot about these patches.  But given that this is a new driver, it
  can't introduce any regression so I thought it could still be OK.

  This has been in linux-next for months now"

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
  hwmon: (i5500_temp) Convert to module_pci_driver
  hwmon: (i5500_temp) Don't bind to disabled sensors
  hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
  hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets