- 20 Nov, 2019 20 commits
-
-
Grygorii Strashko authored
Add CONFIG_TI_CPSW_SWITCHDEV option to enable new cpsw switchdev driver Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
Add DT nodes for new cpsw switchdev driver for am571x-idk board for now to enable testing of the new solution. Signed-off-by:
-
Grygorii Strashko authored
Add DT nodes for new cpsw switch dev driver. Signed-off-by:
-
Ilias Apalodimas authored
A new cpsw dirver based on switchdev was added. Add documentation about basic configuration and future features Signed-off-by:
Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by:
-
Grygorii Strashko authored
Add dependency from TI_CPSW_SWITCHDEV. Signed-off-by:
-
Ilias Apalodimas authored
CPSW switchdev based driver which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. The Switch mode can be enabled by configuring devlink driver parameter "switch_mode" to 1: devlink dev param set platform/48484000.switch \ name switch_mode value 1 cmode runtime This can be done regardless of the state of Port's netdevs - UP/DOWN, but Port's netdev devices have to be UP before joining the bridge to avoid overwriting of bridge configuration as CPSW switch driver completely reloads its configuration when first Port changes its state to UP. When the both interfaces joined the bridge - CPSW switch driver will start marking packets with offload_fwd_mark flag unless "ale_bypass=0". All configuration is implemented via switchdev API and notifiers. Supported: - SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD - SWITCHDEV_ATTR_ID_PORT_STP_STATE - SWITCHDEV_OBJ_ID_PORT_VLAN - SWITCHDEV_OBJ_ID_PORT_MDB - SWITCHDEV_OBJ_ID_HOST_MDB Hence CPSW switchdev driver supports: - FDB offloading - MDB offloading - VLAN filtering and offloading - STP Signed-off-by:
-
Ilias Apalodimas authored
Part 1: Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in dual-emac mode by default, thus working as 2 individual network interfaces. Main differences from legacy CPSW driver are: - optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in promiscuous mode will keep possibility of mcast and vlan filtering, which is provides significant benefits when ports are joined to the same bridge, but without enabling "switch" mode, or to different bridges. - learning disabled on ports as it make not too much sense for segregated ports - no forwarding in HW. - enabled basic support for devlink. devlink dev show platform/48484000.switch devlink dev param show platform/48484000.switch: name ale_bypass type driver-specific values: cmode runtime value false - "ale_bypass" devlink driver parameter allows to enable ALE_CONTROL(4).BYPASS mode for debug purposes. - updated DT bindings. Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Signed-off-by:
-
Grygorii Strashko authored
Add bindings for the new TI CPSW switch driver. Comparing to the legacy bindings (net/cpsw.txt): - ports definition follows DSA bindings (net/dsa/dsa.txt) and ports can be marked as "disabled" if not physically wired. - all deprecated properties dropped; - all legacy propertiies dropped which represent constant HW cpapbilities (cpdma_channels, ale_entries, bd_ram_size, mac_control, slaves, active_slave) - TI CPTS DT properties are reused as is, but grouped in "cpts" sub-node - TI Davinci MDIO DT bindings are reused as is, because Davinci MDIO is reused. Signed-off-by:
-
Grygorii Strashko authored
As a preparatory patch to add support for a switchdev based cpsw driver, move common functions to cpsw-priv.c so that they can be used across both drivers. Signed-off-by:
-
Grygorii Strashko authored
A following patches introduce new CPSW switchdev driver which uses common code with legacy CPSW driver. This will introduce build dependency between CPSW switchdev and CPSW legacy drivers related to for_each_slave() and cpsw_slave_index() - they can be compiled both, but only one of them will be not functional depending in Kconfig settings due to duffrences in Slave Ports indexes calculation. To fix this make for_each_slave() local (it's used now only by legacy CPSW driver) and convert cpsw_slave_index() to be a function pointer which is assigned in probe. Driver to probe is defined by DT. Signed-off-by:
-
Ilias Apalodimas authored
A following patch introduces switchdev functionality, so modify ALE engine VLANs/MDBs API: - cpsw_ale_del_mcast(): update so it will remove only selected ports from mcast port_mask or delete whole mcast record if !port_mask - cpsw_ale_del_vlan(): update so it will remove only selected ports from all VLAN record's masks or delete whole VLAN record if !port_mask - add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's masks - add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs Signed-off-by:
-
Grygorii Strashko authored
Now untagged vlan traffic is not support on Host P0 port. This patch adds in ALE context bitmap of VLANs for which Host P0 port bit set in Force Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap(). Signed-off-by:
-
Grygorii Strashko authored
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete or garbage entries from ALE table. Signed-off-by:
-
David S. Miller authored
Pablo Neira Ayuso says: ==================== nf_tables_offload: vlan matching support The following patchset contains Netfilter support for vlan matching offloads: 1) Constify nft_reg_load() as a preparation patch. 2) Restrict rule matching to ingress interface type ARPHRD_ETHER. 3) Add new vlan_tci field to flow_dissector_key_vlan structure, to allow to set up vlan_id, vlan_dei and vlan_priority in one go. 4) C-VLAN matching support. ==================== Signed-off-by: -
Pablo Neira Ayuso authored
Match on h_vlan_encapsulated_proto and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Pablo Neira Ayuso authored
Match on ethertype and set up protocol dependency. Check for protocol dependency before accessing the tci field. Allow to match on the encapsulated ethertype too. Signed-off-by:
-
Pablo Neira Ayuso authored
Hardware offload support at this stage assumes an ethernet device in place. The flow dissector provides the intermediate representation to express this selector, so extend it to allow to store the interface type. Flower does not uses this, so skb_flow_dissect_meta() is not extended to match on this new field. Signed-off-by:
-
Pablo Neira Ayuso authored
This patch constifies the pointer to source register data that is passed as an input parameter. Signed-off-by:
-
Xin Long authored
geneve RFC (draft-ietf-nvo3-geneve-14) allows a geneve packet to carry multiple geneve opts, so it's necessary for lwtunnel to support adding multiple geneve opts in one lwtunnel route. But vxlan and erspan opts are still only allowed to add one option. With this patch, iproute2 could make it like: # ip r a 1.1.1.0/24 encap ip id 1 geneve_opts 0:0:12121212,1:2:12121212 \ dst 10.1.0.2 dev geneve1 # ip r a 1.1.1.0/24 encap ip id 1 vxlan_opts 456 \ dst 10.1.0.2 dev erspan1 # ip r a 1.1.1.0/24 encap ip id 1 erspan_opts 1:123:0:0 \ dst 10.1.0.2 dev erspan1 Which are pretty much like cls_flower and act_tunnel_key. Signed-off-by:Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Rahul Lakkireddy authored
Semicolon is not required at the end of switch block. So, remove it. Addresses coccinelle warning: drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon Fixes: 4846d533 ("cxgb4: add Tx and Rx path for ETHOFLD traffic") Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by:
-
- 19 Nov, 2019 20 commits
-
-
Vladimir Oltean authored
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch and the ENETC: - eno2 <-> swp4, at 2.5G - eno3 <-> swp5, at 1G Only one of the above Ethernet port pairs can act as a DSA link for tagging. When adding initial support for the driver, it was tested only on the 1G eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially (which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't support fixed-link speeds higher than 1G). After making PHYLINK work, it appears that swp4 still can't act as CPU port. So it looks like ocelot_set_cpu_port was being called for swp4, but then it was called again for swp5, overwriting the CPU port assigned in the DT. It appears that when you call dsa_upstream_port for a port that is not defined in the device tree (such as swp5 when using swp4 as CPU port), its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu, and this trips up the following condition in dsa_upstream_port: if (!cpu_dp) return port; So the moral of the story is: don't call dsa_upstream_port for a port that is not defined in the device tree, and therefore its dsa_port structure is not completely initialized (ds->num_ports is still 6). Fixes: 56051948 ("net: dsa: ocelot: add driver for Felix switch family") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Colin Ian King authored
In the case where the call to phy_interface_is_rgmii returns zero the variable ret is left uninitialized and this is returned at the end of the function dp83869_configure_rgmii. Fix this by returning 0 instead of the uninitialized value in ret. Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 01db923e ("net: phy: dp83869: Add TI dp83869 phy") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Xin Long authored
LWTUNNEL_IP_OPT_ERSPAN_VER is u8 type, and nla_put_u8 should have been used instead of nla_put_u32(). This is a copy-paste error. Fixes: b0a21810 ("lwtunnel: add options setting and dumping for erspan") Signed-off-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Updates. This series has the firmware interface update that changes the aRFS/ntuple interface on 57500 chips. The 2nd patch adds a counter and improves the hardware buffer error handling on the 57500 chips. The rest of the series is mainly enhancements on error recovery and firmware reset. ==================== Signed-off-by: -
Pavan Chebbi authored
This is especially beneficial during the NVRAM related firmware commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND flag gets set while waiting for firmware response, abort and return error. Signed-off-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Vasundhara Volam authored
During loss of heartbeat, log this warning message. Signed-off-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
-
Vasundhara Volam authored
For NVM params that are not supported in the current NVM configuration, return the error as -EOPNOTSUPP. Signed-off-by:
-
Vasundhara Volam authored
Report health status update to devlink health reporter, once reset is completed. Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Vasundhara Volam authored
The Linux driver is capable of being the master function to handle resets, so we set the flag to let firmware know. Some other drivers, such as DPDK, is not capable and will not set the flag. Signed-off-by:
-
Vasundhara Volam authored
If firmware supports hot reset, extend ETHTOOL_RESET to support hot reset driver which does not require a driver reload after ETHTOOL_RESET. The driver will go through the same coordinated reset sequence as a firmware initiated fatal/non-fatal reset. Signed-off-by:
-
Vasundhara Volam authored
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related data response from the firmware. These commands take longer than normal commands. Signed-off-by:
-
Michael Chan authored
When hardware reports RX buffer errors, the latest 57500 chips do not require reset. The packet is discarded by the hardware and the ring will continue to operate. Also, add an rx_buf_errors counter for this type of error. It can help the user to identify if the aggregation ring is too small. Signed-off-by:
-
Michael Chan authored
The aRFS ring table interface has changed for the 57500 chips. Updating it accordingly so it will work with the latest production firmware. Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== selftests: Add ethtool and scale tests This patch set adds generic ethtool tests and a mlxsw-specific router scale test for Spectrum-2. Patches #1-#2 from Danielle add the router scale test for Spectrum-2. It re-uses the same test as Spectrum-1, but it is invoked with a different scale, according to what it is queried from devlink-resource. Patches #3-#5 from Amit are a re-work of the ethtool tests that were posted in the past [1]. Patches #3-#4 add the necessary library routines, whereas patch #5 adds the test itself. The test checks both good and bad flows with autoneg on and off. The test plan it detailed in the commit message. Last time Andrew and Florian (copied) provided very useful feedback that is incorporated in this set. Namely: * Parse the value of the different link modes from /usr/include/linux/ethtool.h * Differentiate between supported and advertised speeds and use the latter in autoneg tests * Make the test generic and move it to net/forwarding/ instead of being mlxsw-specific [1] https://patchwork.ozlabs.org/cover/1112903/ ==================== Signed-off-by:
-
Amit Cohen authored
Check configurations and packets transference with different variations of autoneg and speed. Test plan: 1. Test force of same speed with autoneg off 2. Test force of different speeds with autoneg off (should fail) 3. One side is autoneg on and other side sets force of common speeds 4. One side is autoneg on and other side only advertises a subset of the common speeds (one speed of the subset) 5. One side is autoneg on and other side only advertises a subset of the common speeds. Check that highest speed is negotiated 6. Test autoneg on, but each side advertises different speeds (should fail) Signed-off-by:
Amit Cohen <amitc@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Amit Cohen authored
Add a function that waits for device with maximum number of iterations. It enables to limit the waiting and prevent infinite loop. This will be used by the subsequent patch which will set two ports to different speeds in order to make sure they cannot negotiate a link. Waiting for all the setup is limited with 10 minutes for each device. Signed-off-by:
-
Amit Cohen authored
Functions: 1. speeds_arr_get The function returns an array of speed values from /usr/include/linux/ethtool.h The array looks as follows: [10baseT/Half] = 0, [10baseT/Full] = 1, ... 2. ethtool_set: params: cmd The function runs ethtool by cmd (ethtool -s cmd) and checks if there was an error in configuration 3. dev_speeds_get: params: dev, with_mode (0 or 1), adver (0 or 1) return value: Array of supported/Advertised link modes with/without mode * Example 1: speeds_get swp1 0 0 return: 1000 10000 40000 * Example 2: speeds_get swp1 1 1 return: 1000baseKX/Full 10000baseKR/Full 40000baseCR4/Full 4. common_speeds_get: params: dev1, dev2, with_mode (0 or 1), adver (0 or 1) return value: Array of common speeds of dev1 and dev2 * Example: common_speeds_get swp1 swp2 0 0 return: 1000 10000 Assuming that swp1 supports 1000 10000 40000 and swp2 supports 1000 10000 Signed-off-by: -
Danielle Ratson authored
The scale test for Spectrum-2 should only be invoked for Spectrum-2. Skip the test otherwise. Signed-off-by:
Danielle Ratson <danieller@mellanox.com> Signed-off-by:
-
Danielle Ratson authored
Same as for Spectrum-1, test the ability to add the maximum number of routes possible to the switch. Invoke the test from the 'resource_scale' wrapper script. Signed-off-by:
-
David S. Miller authored
Jesper Dangaard says: ==================== page_pool: followup changes to restore tracepoint features This patchset is a followup to Jonathan patch, that do not release pool until inflight == 0. That changed page_pool to be responsible for its own delayed destruction instead of relying on xdp memory model. As the page_pool maintainer, I'm promoting the use of tracepoint to troubleshoot and help driver developers verify correctness when converting at driver to use page_pool. The role of xdp:mem_disconnect have changed, which broke my bpftrace tools for shutdown verification. With these changes, the same capabilities are regained. ==================== Signed-off-by:
-
