- 21 Jul, 2015 40 commits
-
-
Anish Bhatt authored
Signed-off-by:
Anish Bhatt <anish@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Anish Bhatt authored
Signed-off-by:
-
Anish Bhatt authored
Since finally DCB traffic management is still handled by firmware, allow firmware to be fully programmed and queried even in host managed state for the cases where this was previously rejected. Signed-off-by:
-
Anish Bhatt authored
This keeps app format passed to firmware the same irrespective of DCBx version in use. Signed-off-by:
-
Marcelo Ricardo Leitner authored
Cookie ACK is always received by the association initiator, so fix the comment to avoid confusion. Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
David S. Miller authored
Marcelo Ricardo Leitner says: ==================== sctp: fix src address selection if using secondary address This series improves the way SCTP chooses its src address so that the choosen one will always belong to the interface being used for output. v1->v2: - split out the refactoring from the fix itself - Doing a full reverse routing as in v1 is not necessary. Only looking for the interface that has the address and comparing its number is enough. ==================== Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
In short, sctp is likely to incorrectly choose src address if socket is bound to secondary addresses. This patch fixes it by adding a new check that checks if such src address belongs to the interface that routing identified as output. This is enough to avoid rp_filter drops on remote peer. Details: Currently, sctp will do a routing attempt without specifying the src address and compare the returned value (preferred source) with the addresses that the socket is bound to. When using secondary addresses, this will not match. Then it will try specifying each of the addresses that the socket is bound to and re-routing, checking if that address is valid as src for that dst. Thing is, this check alone is weak: # ip r l 192.168.100.0/24 dev eth1 proto kernel scope link src 192.168.100.149 192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.147 # ip a l 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 52:54:00:15:18:6a brd ff:ff:ff:ff:ff:ff inet 192.168.122.147/24 brd 192.168.122.255 scope global dynamic eth0 valid_lft 2160sec preferred_lft 2160sec inet 192.168.122.148/24 scope global secondary eth0 valid_lft forever preferred_lft forever inet6 fe80::5054:ff:fe15:186a/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 52:54:00:b3:91:46 brd ff:ff:ff:ff:ff:ff inet 192.168.100.149/24 brd 192.168.100.255 scope global dynamic eth1 valid_lft 2162sec preferred_lft 2162sec inet 192.168.100.148/24 scope global secondary eth1 valid_lft forever preferred_lft forever inet6 fe80::5054:ff:feb3:9146/64 scope link valid_lft forever preferred_lft forever 4: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 52:54:00:05:47:ee brd ff:ff:ff:ff:ff:ff inet6 fe80::5054:ff:fe05:47ee/64 scope link valid_lft forever preferred_lft forever # ip r g 192.168.100.193 from 192.168.122.148 192.168.100.193 from 192.168.122.148 dev eth1 cache Even if you specify an interface: # ip r g 192.168.100.193 from 192.168.122.148 oif eth1 192.168.100.193 from 192.168.122.148 dev eth1 cache Although this would be valid, peers using rp_filter will drop such packets as their src doesn't match the routes for that interface. Signed-off-by: -
Marcelo Ricardo Leitner authored
Paves the day for the next patch. Functionality stays untouched. Signed-off-by:
-
Sowmini Varadhan authored
__vxlan_find_mac invokes ether_addr_equal on the eth_addr field, which triggers unaligned access messages, so rearrange vxlan_fdb to avoid this in the most non-intrusive way. Signed-off-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Reviewed-by:
Jiri Pirko <jiri@resnulli.us> Reviewed-by:
-
Thomas Graf authored
Depending on system speed, the large lookup/insert/delete loops of the testsuite can take a considerable amount of time to complete causing watchdog warnings to appear. Allow other tasks to be scheduled throughout the loops. Reported-by:
Meelis Roos <mroos@linux.ee> Signed-off-by:
Thomas Graf <tgraf@suug.ch> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Shaohui Xie authored
Teranetics TN2020 is compliant with IEEE 802.3an 10 Gigabit. Signed-off-by:
Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by:
-
David S. Miller authored
Alexei Starovoitov says: ==================== bpf: introduce bpf_skb_vlan_push/pop() helpers Let TC+eBPF programs call skb_vlan_push/pop via helpers. v1->v2: - reworded commit log to better explain correctness of re-caching and fixed comparison of mixed endiannes (suggested by Eric) ==================== Signed-off-by: -
Alexei Starovoitov authored
improve accuracy of timing in test_bpf and add two stress tests: - {skb->data[0], get_smp_processor_id} repeated 2k times - {skb->data[0], vlan_push} x 68 followed by {skb->data[0], vlan_pop} x 68 1st test is useful to test performance of JIT implementation of BPF_LD_ABS together with BPF_CALL instructions. 2nd test is stressing skb_vlan_push/pop logic together with skb->data access via BPF_LD_ABS insn which checks that re-caching of skb->data is done correctly. In order to call bpf_skb_vlan_push() from test_bpf.ko have to add three export_symbol_gpl. Signed-off-by:Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
-
Alexei Starovoitov authored
Allow eBPF programs attached to TC qdiscs call skb_vlan_push/pop via helper functions. These functions may change skb->data/hlen which are cached by some JITs to improve performance of ld_abs/ld_ind instructions. Therefore JITs need to recognize bpf_skb_vlan_push/pop() calls, re-compute header len and re-cache skb->data/hlen back into cpu registers. Note, skb->data/hlen are not directly accessible from the programs, so any changes to skb->data done either by these helpers or by other TC actions are safe. eBPF JIT supported by three architectures: - arm64 JIT is using bpf_load_pointer() without caching, so it's ok as-is. - x64 JIT re-caches skb->data/hlen unconditionally after vlan_push/pop calls (experiments showed that conditional re-caching is slower). - s390 JIT falls back to interpreter for now when bpf_skb_vlan_push() is present in the program (re-caching is tbd). These helpers allow more scalable handling of vlan from the programs. Instead of creating thousands of vlan netdevs on top of eth0 and attaching TC+ingress+bpf to all of them, the program can be attached to eth0 directly and manipulate vlans as necessary. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-07-17 This series contains updates to igb, ixgbe, ixgbevf, i40e, bnx2x, freescale, siena and dp83640. Jacob provides several patches to clarify the intended way to implement both SIOCSHWTSTAMP and ethtool's get_ts_info(). It is okay to support the specific filters in SIOCSHWTSTAMP by upscaling them to the generic filters. Alex Duyck provides a igb patch to pull the time stamp from the fragment before it gets added to the skb, to avoid a possible issue in which the fragment can possibly be less than IGB_RX_HDR_LEN due to the time stamp being pulled after the copybreak check. Also provides a ixgbevf patch to fold the ixgbevf_pull_tail() call into ixgbevf_add_rx_frag(), which gives the advantage that the fragment does not have to be modified after it is added to the skb. Fan provides patches for ixgbe/ixgbevf to set the receive hash type based on receive descriptor RSS type. Todd provides a fix for igb where on check for link on any media other than copper was not being detected since it was looking on the incorrect PHY page (due to the page being used gets switched before the function to check link gets executed). ==================== Signed-off-by: -
David S. Miller authored
Florian Fainelli says: ==================== net: bcmgenet: PHY initialization rework This patch series reworks how we perform PHY initialization and resets in the GENET driver. Although this contains mostly fixes, some of the changes are a bit too intrusive to be backported to 'net' at the moment. Some of the motivations behind these changes were to reduce the time spent in how performing MDIO transactions, since it is better to perform then when we have interrupts enabled. This reduces the bring-up time of GENET from ~600 msecs down to ~8 msecs, and about the same time for suspend/resume. Since I do not currently have a system which is not DT-aware, can you (Petri, Jaedon) give this a try and confirm things keep working as expected? ==================== Signed-off-by: -
Florian Fainelli authored
Now that we have reworked the way we perform the PHY initialization, we no longer need to differentiate between init time vs. non-init time calls, just use a dev_info_once() print to print the PHY type. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
We are currently doing a full PHY initialization and even starting the pHY state machine during bcmgenet_mii_init() which is executed in the driver's probe function. This is convenient to determine whether we can attach to a proper PHY device but comes at the expense of spending up to 10ms per MDIO transactions (to reach the waitqueue timeout), which slows things down. This also creates a sitaution where we end-up attaching twice to the PHY, which is not quite correct either. Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update its error path accordingly. Avoid printing the message "attached PHY at address 1 [...]" every time we bring up/down the interface and remove this print since it duplicates what the PHY driver already does for us. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Florian Fainelli authored
Our internal GPHY might be powered off before we attempt scanning the MDIO bus and bind a driver to it. The way we are currently determining whether a PHY is internal or not is done *after* we have successfully matched its driver. If the PHY is powered down, it will not respond to the MDIO bus, so we will not be able to bind a driver to it. Our Device Tree for GENET interfaces specifies a "phy-mode" value: "internal" which tells if this internal uses an internal PHY or not. If of_get_phy_mode() fails to parse the 'phy-mode' property, do an additional manual lookup, and if we find "internal" set the corresponding internal variable accordingly. Replace all uses of phy_is_internal() with a check against priv->internal_phy to avoid having to rely on whether or not priv->phydev is set correctly. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Florian Fainelli authored
We are currently disabling the GPHY interface during bcmgenet_close(), and attempting to power it back on during bcmgenet_open(). This works fine for the first time, because we called bcmgenet_mii_config() which took care of enabling the interface, however, bcmgenet_power_up() really needs to power on the GPHY for correctness. This will be particularly important as we want to move bcmgenet_mii_probe() down to bcmgenet_open() to avoid seeing the "PHY already attached" message. Fixes: a642c4f7 ("net: bcmgenet: power up and down integrated GPHY when unused") Signed-off-by:
-
Florian Fainelli authored
bcmgenet_open()'s error path call free_irq() with a dev_id argument different from the one we used to call request_irq() with, this will make us trip over the warning in kernel/irq/manage.c:__free_irq() Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Florian Fainelli authored
We are currently issuing multiple PHY resets during a suspend/resume, first during bcmgenet_power_up() which does a hardware reset, then a software reset by calling bcmgenet_mii_reset(). This is both unnecessary and can take as long as 10ms per MDIO transactions while we re-apply workarounds because we do not yet have MDIO interrupts enabled. phy_resume() takes care of re-apply our workarounds in case we need any, and bcmgenet_power_up() does a PHY hardware reset, all of this is more than enough to guarantee that the PHY operates correctly. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
David S. Miller authored
Joachim Eastwood says: ==================== stmmac clean up for 4.3 part1 This patch set continues the conversion of the dwmac glue layers to more proper platform drivers. The first part of the patch set cleans up stmmac_platform a bit. Refactors code from the common probe function and exports two functions that will be used in the dwmac-* drivers. Second part converts two simple dwmac-* drivers to have their own probe function and use the exported functions. This brings us closer to point where stmmac_platform is only a library of common functions for the dwmac-* drivers to use. The plan next is: * add probe functions to the rest of the dwmac-* drivers * move probe function in stmmac_platform to dwmac-generic * remove struct stmmac_of_data and let those drivers that actually need match data handle it themselves * clean up include/linux/stmmac.h Note that this patch set has only been tested on lpc18xx so testing on other platforms is greatly appreciated. Previous parts can be found here: http://www.spinics.net/lists/netdev/msg328997.html http://www.spinics.net/lists/netdev/msg329932.html ==================== Signed-off-by:
-
Joachim Eastwood authored
Both of these fields are unused and has been unused since they were added 3 and 5 years ago. Drop them since they are clearly not very useful. Signed-off-by:
Joachim Eastwood <manabian@gmail.com> Signed-off-by:
-
Joachim Eastwood authored
By using a few functions from stmmac_platform we can now create a proper probe function in this driver. By doing so we can drop the OF match data and simplify the overall driver. Signed-off-by:
-
Joachim Eastwood authored
By using a few functions from stmmac_platform we can now create a proper probe function in this driver. By doing so we can drop the OF match data and simplify the overall driver. Signed-off-by:
-
Joachim Eastwood authored
Export stmmac_probe_config_dt() and stmmac_get_platform_resources() so they can be used in the dwmac-* drivers themselves. This will allow us to build more flexible and standalone drivers which just use stmmac_platform as a library for setup functions. Signed-off-by:
-
Joachim Eastwood authored
Since stmmac_probe_config_dt() allocates the platform data structure it is cleaner if it just returned this structure directly. This function will later be used in the probe function in dwmac-* drivers. Signed-off-by:
-
Joachim Eastwood authored
Refactor all code that deals with platform resources into it's own get function. This function will later be used in the probe function in dwmac-* drivers. Signed-off-by:
-
Joachim Eastwood authored
Refactor code to clearly separate probing non-dt versus dt. In the non-dt case platform data must be supplied to probe successfully. For dt the platform data structure is created and match data is copied into it. Note that support for supplying platform data in dt from AUXDATA is dropped as no users in mainline does this. This change will allow dt dwmac-* drivers to call the config_dt() function from probe to create the needed platform data struct and retrieve common dt properties. Signed-off-by:
-
Joachim Eastwood authored
By using of_device_get_match_data() the code that retrieve match data can be simplified quite a bit. Signed-off-by:
-
David S. Miller authored
Jon Maloy says: ==================== tipc: separate link and link aggregation layer This is the first batch of a longer series that has two main objectives: o Finer lock granularity during message sending and reception, especially regarding usage of the node spinlock. o Better separation between the link layer implementation and the link aggregation layer, represented by node.c::struct tipc_node. Hopefully these changes also make this part of code somewhat easier to comprehend and maintain. ==================== Signed-off-by: -
Jon Paul Maloy authored
We convert packet/message reception according to the same principle we have been using for message sending and timeout handling: We move the function tipc_rcv() to node.c, hence handling the initial packet reception at the link aggregation level. The function grabs the node lock, selects the receiving link, and accesses it via a new call tipc_link_rcv(). This function appends buffers to the input queue for delivery upwards, but it may also append outgoing packets to the xmit queue, just as we do during regular message sending. The latter will happen when buffers are forwarded from the link backlog, or when retransmission is requested. Upon return of this function, and after having released the node lock, tipc_rcv() delivers/tranmsits the contents of those queues, but it may also perform actions such as link activation or reset, as indicated by the return flags from the link. This reduces the number of cpu cycles spent inside the node spinlock, and reduces contention on that lock. Reviewed-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Jon Paul Maloy authored
The logics for determining when a node is permitted to establish and maintain contact with its peer node becomes non-trivial in the presence of multiple parallel links that may come and go independently. A known failure scenario is that one endpoint registers both its links to the peer lost, cleans up it binding table, and prepares for a table update once contact is re-establihed, while the other endpoint may see its links reset and re-established one by one, hence seeing no need to re-synchronize the binding table. To avoid this, a node must not allow re-establishing contact until it has confirmation that even the peer has lost both links. Currently, the mechanism for handling this consists of setting and resetting two state flags from different locations in the code. This solution is hard to understand and maintain. A closer analysis even reveals that it is not completely safe. In this commit we do instead introduce an FSM that keeps track of the conditions for when the node can establish and maintain links. It has six states and four events, and is strictly based on explicit knowledge about the own node's and the peer node's contact states. Only events leading to state change are shown as edges in the figure below. +--------------+ | SELF_UP/ | +---------------->| PEER_COMING |-----------------+ SELF_ | +--------------+ |PEER_ ESTBL_ | | |ESTBL_ CONTACT| SELF_LOST_CONTACT | |CONTACT | v | | +--------------+ | | PEER_ | SELF_DOWN/ | SELF_ | | LOST_ +--| PEER_LEAVING |<--+ LOST_ v +-------------+ CONTACT | +--------------+ | CONTACT +-----------+ | SELF_DOWN/ |<----------+ +----------| SELF_UP/ | | PEER_DOWN |<----------+ +----------| PEER_UP | +-------------+ SELF_ | +--------------+ | PEER_ +-----------+ | LOST_ +--| SELF_LEAVING/|<--+ LOST_ A | CONTACT | PEER_DOWN | CONTACT | | +--------------+ | | A | PEER_ | PEER_LOST_CONTACT | |SELF_ ESTBL_ | | |ESTBL_ CONTACT| +--------------+ |CONTACT +---------------->| PEER_UP/ |-----------------+ | SELF_COMING | +--------------+ Reviewed-by: -
Jon Paul Maloy authored
In our effort to move control of the links to the link aggregation layer, we move the perodic link supervision timer to struct tipc_node. The new timer is shared between all links belonging to the node, thus saving resources, while still kicking the FSM on both its pertaining links at each expiration. The current link timer and corresponding functions are removed. Reviewed-by:
-
Jon Paul Maloy authored
We create a second, simpler, link timer function, tipc_link_timeout(). The new function makes use of the new FSM function introduced in the previous commit, and just like it, takes a buffer queue as parameter. It returns an event bit field and potentially a link protocol packet to the caller. The existing timer function, link_timeout(), is still needed for a while, so we redesign it to become a wrapper around the new function. Reviewed-by:
-
Jon Paul Maloy authored
The link FSM implementation is currently unnecessarily complex. It sometimes checks for conditional state outside the FSM data before deciding next state, and often performs actions directly inside the FSM logics. In this commit, we create a second, simpler FSM implementation, that as far as possible acts only on states and events that it is strictly defined for, and postpone any actions until it is finished with its decisions. It also returns an event flag field and an a buffer queue which may potentially contain a protocol message to be sent by the caller. Unfortunately, we cannot yet make the FSM "clean", in the sense that its decisions are only based on FSM state and event, and that state changes happen only here. That will have to wait until the activate/reset logics has been cleaned up in a future commit. We also rename the link states as follows: WORKING_WORKING -> TIPC_LINK_WORKING WORKING_UNKNOWN -> TIPC_LINK_PROBING RESET_UNKNOWN -> TIPC_LINK_RESETTING RESET_RESET -> TIPC_LINK_ESTABLISHING The existing FSM function, link_state_event(), is still needed for a while, so we redesign it to make use of the new function. Reviewed-by:
-
Jon Paul Maloy authored
As a preparation for later changes, we introduce a new function tipc_link_build_proto_msg(). Instead of actually sending the created protocol message, it only creates it and adds it to the head of a skb queue provided by the caller. Since we still need the existing function tipc_link_protocol_xmit() for a while, we redesign it to make use of the new function. Reviewed-by:
-
Jon Paul Maloy authored
The status flag LINK_STOPPED is not needed any more, since the mechanism for delayed deletion of links has been removed. Likewise, LINK_STARTED and LINK_START_EVT are unnecessary, because we can just as well start the link timer directly from inside tipc_link_create(). We eliminate these flags in this commit. Instead of the above flags, we now introduce three new link modes, TIPC_LINK_OPEN, TIPC_LINK_BLOCKED and TIPC_LINK_TUNNEL. The values indicate whether, and in the case of TIPC_LINK_TUNNEL, which, messages the link is allowed to receive in this state. TIPC_LINK_BLOCKED also blocks timer-driven protocol messages to be sent out, and any change to the link FSM. Since the modes are mutually exclusive, we convert them to state values, and rename the 'flags' field in struct tipc_link to 'exec_mode'. Finally, we move the #defines for link FSM states and events from link.h into enums inside the file link.c, which is the real usage scope of these definitions. Reviewed-by:
-
Jon Paul Maloy authored
Currently, message sending is performed through a deep call chain, where the node spinlock is grabbed and held during a significant part of the transmission time. This is clearly detrimental to overall throughput performance; it would be better if we could send the message after the spinlock has been released. In this commit, we do instead let the call revert on the stack after the buffer chain has been added to the transmission queue, whereafter clones of the buffers are transmitted to the device layer outside the spinlock scope. As a further step in our effort to separate the roles of the node and link entities we also move the function tipc_link_xmit() to node.c, and rename it to tipc_node_xmit(). Reviewed-by:
-
