- 18 Nov, 2019 19 commits
-
-
Shuiqing Li authored
The device driver data saved the 'struct sprd_wdt' object, it is incorrect to get 'struct watchdog_device' object from the driver data, thus fix it. Fixes: 47760346 ("watchdog: Add Spreadtrum watchdog driver") Reported-by:
Dongwei Wang <dongwei.wang@unisoc.com> Signed-off-by:
Shuiqing Li <shuiqing.li@unisoc.com> Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/76d4687189ec940baa90cb8d679a8d4c8f02ee80.1573210405.git.baolin.wang@linaro.orgSigned-off-by:
Wim Van Sebroeck <wim@linux-watchdog.org>
-
Joel Stanley authored
The ast2600 no longer uses bit 4 in the control register to indicate a 1MHz clock (It now controls whether this watchdog is reset by a SOC reset). This means we do not want to set it. It also does not need to be set for the ast2500, as it is read-only on that SoC. The comment next to the clock rate selection wandered away from where it was set, so put it back next to the register setting it's describing. Fixes: b3528b48 ("watchdog: aspeed: Add support for AST2600") Signed-off-by:
Joel Stanley <joel@jms.id.au> Reviewed-by:
Cédric Le Goater <clg@kaod.org> Reviewed-by:
-
Fabio Estevam authored
The following hang is observed when a 'reboot' command is issued: # reboot # Stopping network: OK Stopping klogd: OK Stopping syslogd: OK umount: devtmpfs busy - remounted read-only [ 8.612079] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) The system is going down NOW! Sent SIGTERM to all processes Sent SIGKILL to all processes Requesting system reboot [ 10.694753] reboot: Restarting system [ 11.699008] Reboot failed -- System halted Fix this problem by adding a .restart ops member. Fixes: 41b630f4 ("watchdog: Add i.MX7ULP watchdog support") Signed-off-by:
Fabio Estevam <festevam@gmail.com> Reviewed-by:
-
Rasmus Villemoes authored
It can be useful to delay setting the nowayout feature for a watchdog device. Moreover, not every driver (notably gpio_wdt) implements a nowayout module parameter/otherwise respects CONFIG_WATCHDOG_NOWAYOUT, and modifying those drivers carries a risk of causing a regression for someone who has two watchdog devices, sets CONFIG_WATCHDOG_NOWAYOUT and somehow relies on the gpio_wdt driver being ignorant of that (i.e., allowing one to gracefully close a gpio_wdt but not the other watchdog in the system). So instead, simply make the nowayout sysfs file writable. Obviously, setting nowayout is a one-way street. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by:
-
Julia Cartwright authored
When PREEMPT_RT is enabled, all hrtimer expiry functions are deferred for execution into the context of ksoftirqd unless otherwise annotated. Deferring the expiry of the hrtimer used by the watchdog core, however, is a waste, as the callback does nothing but queue a kthread work item and wakeup watchdogd. It's worst then that, too: the deferral through ksoftirqd also means that for correct behavior a user must adjust the scheduling parameters of both watchdogd _and_ ksoftirqd, which is unnecessary and has other side effects (like causing unrelated expiry functions to execute at potentially elevated priority). Instead, mark the hrtimer used by the watchdog core as being _HARD to allow it's execution directly from hardirq context. The work done in this expiry function is well-bounded and minimal. A user still must adjust the scheduling parameters of the watchdogd to be correct w.r.t. their application needs. Link: https://lkml.kernel.org/r/0e02d8327aeca344096c246713033887bc490dd7.1538089180.git.julia@ni.com Cc: Guenter Roeck <linux@roeck-us.net> Reported-and-tested-by:
Steffen Trumtrar <s.trumtrar@pengutronix.de> Reported-by:
Tim Sander <tim@krieglstein.org> Signed-off-by:
Julia Cartwright <julia@ni.com> Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by:
-
Fabio Estevam authored
Use definitions instead of magic values in order to improve readability. Since the CLK field of the WDOG CS register is composed of two bits to select the watchdog clock source, use a shift representation instead of BIT(). Signed-off-by:
-
Fabio Estevam authored
Compiler is smart enough and knows when to inline, so there is no need to mark some of these functions as 'inline'. Remove such annotations. Signed-off-by:
-
Fabio Estevam authored
The 'notifier_block' structure member is unused, so just remove it. Signed-off-by:
-
Fabio Estevam authored
It is more natural to pass the watchdog instance inside imx7ulp_wdt_enable() instead of the base address. This also has the benefit to reduce the code a bit. Signed-off-by:
-
Geert Uytterhoeven authored
Fix misspelling of "configurable". Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
-
Matti Vaittinen authored
The function documentation for the exported ROHM BD70528 WDG control functions used old argument names. Fix the names. Signed-off-by:
Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Reviewed-by:
-
Michal Simek authored
There is no reason to show error message if clocks are not ready yet. Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Reviewed-by:
-
Kevin Hao authored
The struct cdev is embedded in the struct watchdog_core_data. In the current code, we manage the watchdog_core_data with a kref, but the cdev is manged by a kobject. There is no any relationship between this kref and kobject. So it is possible that the watchdog_core_data is freed before the cdev is entirely released. We can easily get the following call trace with CONFIG_DEBUG_KOBJECT_RELEASE and CONFIG_DEBUG_OBJECTS_TIMERS enabled. ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x38 WARNING: CPU: 23 PID: 1028 at lib/debugobjects.c:481 debug_print_object+0xb0/0xf0 Modules linked in: softdog(-) deflate ctr twofish_generic twofish_common camellia_generic serpent_generic blowfish_generic blowfish_common cast5_generic cast_common cmac xcbc af_key sch_fq_codel openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 CPU: 23 PID: 1028 Comm: modprobe Not tainted 5.3.0-next-20190924-yoctodev-standard+ #180 Hardware name: Marvell OcteonTX CN96XX board (DT) pstate: 00400009 (nzcv daif +PAN -UAO) pc : debug_print_object+0xb0/0xf0 lr : debug_print_object+0xb0/0xf0 sp : ffff80001cbcfc70 x29: ffff80001cbcfc70 x28: ffff800010ea2128 x27: ffff800010bad000 x26: 0000000000000000 x25: ffff80001103c640 x24: ffff80001107b268 x23: ffff800010bad9e8 x22: ffff800010ea2128 x21: ffff000bc2c62af8 x20: ffff80001103c600 x19: ffff800010e867d8 x18: 0000000000000060 x17: 0000000000000000 x16: 0000000000000000 x15: ffff000bd7240470 x14: 6e6968207473696c x13: 5f72656d6974203a x12: 6570797420746365 x11: 6a626f2029302065 x10: 7461747320657669 x9 : 7463612820657669 x8 : 3378302f3078302b x7 : 0000000000001d7a x6 : ffff800010fd5889 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : ffff000bff948548 x1 : 276a1c9e1edc2300 x0 : 0000000000000000 Call trace: debug_print_object+0xb0/0xf0 debug_check_no_obj_freed+0x1e8/0x210 kfree+0x1b8/0x368 watchdog_cdev_unregister+0x88/0xc8 watchdog_dev_unregister+0x38/0x48 watchdog_unregister_device+0xa8/0x100 softdog_exit+0x18/0xfec4 [softdog] __arm64_sys_delete_module+0x174/0x200 el0_svc_handler+0xd0/0x1c8 el0_svc+0x8/0xc This is a common issue when using cdev embedded in a struct. Fortunately, we already have a mechanism to solve this kind of issue. Please see commit 233ed09d ("chardev: add helper function to register char devs with a struct device") for more detail. In this patch, we choose to embed the struct device into the watchdog_core_data, and use the API provided by the commit 233ed09d to make sure that the release of watchdog_core_data and cdev are in sequence. Signed-off-by:
Kevin Hao <haokexin@gmail.com> Reviewed-by:
-
Borislav Petkov authored
... by moving the fall through comment outside of the code block so that gcc sees it. No functional changes. Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Wim Van Sebroeck <wim@linux-watchdog.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-watchdog@vger.kernel.org Reviewed-by:
-
Andy Shevchenko authored
Normally, the watchdog is disabled when /dev/watchdog is closed, but if CONFIG_WATCHDOG_NOWAYOUT is defined, then it means that the watchdog should remain enabled. So we should keep it enabled if CONFIG_WATCHDOG_NOWAYOUT is defined. Reported-by:
Razvan Becheriu <razvan.becheriu@qualitance.com> Cc: Ferry Toth <fntoth@gmail.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Razvan Becheriu <razvan.becheriu@gmail.com> Link: https://lore.kernel.org/r/20190924143116.69823-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Anson Huang authored
Add helper variable dev = &pdev->dev to simply the code. Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Reviewed-by:
-
Anson Huang authored
Use __maybe_unused for power management related functions instead of #if CONFIG_PM_SLEEP to simply the code. Signed-off-by:
-
Anson Huang authored
Remove unnecessary blank line. Signed-off-by:
-
Srikanth Krishnakar authored
The watchdog controller on NCT6116D is compatible with NCT6102D. Extend the support to enable SuperIO based NCT6116D watchdog device. Signed-off-by:
Srikanth Krishnakar <Srikanth_Krishnakar@mentor.com> Reviewed-by:
-
- 11 Nov, 2019 1 commit
-
-
Linus Torvalds authored
-
- 10 Nov, 2019 13 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "A set of fixes that have trickled in over the last couple of weeks: - MAINTAINER update for Cavium/Marvell ThunderX2 - stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for CAN interfaces - i.MX fixes for voltage regulator GPIO mappings, fixes voltage scaling issues - More i.MX fixes for various issues on i.MX eval boards: interrupt storm due to u-boot leaving pins in new states, fixing power button config, a couple of compatible-string corrections. - Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets - A few documentation tweaks and a fix of a memory leak in the reset subsystem" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: MAINTAINERS: update Cavium ThunderX2 maintainers ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1 ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1 ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157 arm64: dts: zii-ultra: fix ARM regulator GPIO handle ARM: sunxi: Fix CPU powerdown on A83T ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend arm64: dts: imx8mn: fix compatible string for sdma arm64: dts: imx8mm: fix compatible string for sdma reset: fix reset_control_ops kerneldoc comment ARM: dts: imx6-logicpd: Re-enable SNVS power key soc: imx: gpc: fix initialiser format ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts arm64: dts: ls1028a: fix a compatible issue reset: fix reset_control_get_exclusive kerneldoc comment reset: fix reset_control_lookup kerneldoc comment reset: fix of_reset_control_get_count kerneldoc comment reset: fix of_reset_simple_xlate kerneldoc comment reset: Fix memory leak in reset_control_array_put() -
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull IIO fixes and staging driver from Greg KH: "Here is a mix of a number of IIO driver fixes for 5.4-rc7, and a whole new staging driver. The IIO fixes resolve some reported issues, all are tiny. The staging driver addition is the vboxsf filesystem, which is the VirtualBox guest shared folder code. Hans has been trying to get filesystem reviewers to review the code for many months now, and Christoph finally said to just merge it in staging now as it is stand-alone and the filesystem people can review it easier over time that way. I know it's late for this big of an addition, but it is stand-alone. The code has been in linux-next for a while, long enough to pick up a few tiny fixes for it already so people are looking at it. All of these have been in linux-next with no reported issues" * tag 'staging-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: Fix error return code in vboxsf_fill_super() staging: vboxsf: fix dereference of pointer dentry before it is null checked staging: vboxsf: Remove unused including <linux/version.h> staging: Add VirtualBox guest shared folder (vboxsf) support iio: adc: stm32-adc: fix stopping dma iio: imu: inv_mpu6050: fix no data on MPU6050 iio: srf04: fix wrong limitation in distance measuring iio: imu: adis16480: make sure provided frequency is positive
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull char/misc driver fixes from Greg KH: "Here are a number of late-arrival driver fixes for issues reported for some char/misc drivers for 5.4-rc7 These all come from the different subsystem/driver maintainers as things that they had reports for and wanted to see fixed. All of these have been in linux-next with no reported issues" * tag 'char-misc-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: intel_th: pci: Add Jasper Lake PCH support intel_th: pci: Add Comet Lake PCH support intel_th: msu: Fix possible memory leak in mode_store() intel_th: msu: Fix overflow in shift of an unsigned int intel_th: msu: Fix missing allocation failure check on a kstrndup intel_th: msu: Fix an uninitialized mutex intel_th: gth: Fix the window switching sequence soundwire: slave: fix scanf format soundwire: intel: fix intel_register_dai PDI offsets and numbers interconnect: Add locking in icc_set_tag() interconnect: qcom: Fix icc_onecell_data allocation soundwire: depend on ACPI || OF soundwire: depend on ACPI thunderbolt: Drop unnecessary read when writing LC command in Ice Lake thunderbolt: Fix lockdep circular locking depedency warning thunderbolt: Read DP IN adapter first two dwords in one go
-
git://git.infradead.org/users/hch/configfsLinus Torvalds authored
Pull configfs regression fix from Christoph Hellwig: "Fix a regression from this merge window in the configfs symlink handling (Honggang Li)" * tag 'configfs-for-5.4-2' of git://git.infradead.org/users/hch/configfs: configfs: calculate the depth of parent item
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A small set of fixes for x86: - Make the tsc=reliable/nowatchdog command line parameter work again. It was broken with the introduction of the early TSC clocksource. - Prevent the evaluation of exception stacks before they are set up. This causes a crash in dumpstack because the stack walk termination gets screwed up. - Prevent a NULL pointer dereference in the rescource control file system. - Avoid bogus warnings about APIC id mismatch related to the LDR which can happen when the LDR is not in use and therefore not initialized. Only evaluate that when the APIC is in logical destination mode" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/tsc: Respect tsc command line paraemeter for clocksource_tsc_early x86/dumpstack/64: Don't evaluate exception stacks before setup x86/apic/32: Avoid bogus LDR warnings x86/resctrl: Prevent NULL pointer dereference when reading mondata -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "A small set of fixes for timekeepoing and clocksource drivers: - VDSO data was updated conditional on the availability of a VDSO capable clocksource. This causes the VDSO functions which do not depend on a VDSO capable clocksource to operate on stale data. Always update unconditionally. - Prevent a double free in the mediatek driver - Use the proper helper in the sh_mtu2 driver so it won't attempt to initialize non-existing interrupts" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timekeeping/vsyscall: Update VDSO data unconditionally clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name() clocksource/drivers/mediatek: Fix error handling -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixes from Thomas Gleixner: "Two fixes for scheduler regressions: - Plug a subtle race condition which was introduced with the rework of the next task selection functionality. The change of task properties became unprotected which can be observed inconsistently causing state corruption. - A trivial compile fix for CONFIG_CGROUPS=n" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched: Fix pick_next_task() vs 'change' pattern race sched/core: Fix compilation error when cgroup not selected -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf tooling fixes from Thomas Gleixner: - Fix the time sorting algorithm which was broken due to truncation of big numbers - Fix the python script generator fail caused by a broken tracepoint array iterator * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf tools: Fix time sorting perf tools: Remove unused trace_find_next_event() perf scripting engines: Iterate on tep event arrays directly
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixlet from Thomas Gleixner: "A trivial fix for a kernel doc regression where an argument change was not reflected in the documentation" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull stacktrace fix from Thomas Gleixner: "A small fix for a stacktrace regression. Saving a stacktrace for a foreign task skipped an extra entry which makes e.g. the output of /proc/$PID/stack incomplete" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: stacktrace: Don't skip first entry on noncurrent tasks
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fix from Steve French: "Small fix for an smb3 reconnect bug (also marked for stable)" * tag '5.4-rc7-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6: SMB3: Fix persistent handles reconnect
-
Corentin Labbe authored
config option GENERIC_IO was removed but still selected by lib/kconfig This patch finish the cleaning. Fixes: 9de8da47 ("kconfig: kill off GENERIC_IO option") Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Corentin Labbe <clabbe@baylibre.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlLinus Torvalds authored
Pull pin control fixes from Linus Walleij: - Fix glitch risks in the Intel GPIO - Fix the Intel Cherryview valid irq mask calculation. - Allocate the Intel Cherryview irqchip dynamically. - Fix the valid mask init sequency on the ST STMFX driver. * tag 'pinctrl-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: stmfx: fix valid_mask init sequence pinctrl: cherryview: Allocate IRQ chip dynamic pinctrl: cherryview: Fix irq_valid_mask calculation pinctrl: intel: Avoid potential glitches if pin is in GPIO mode
-
- 09 Nov, 2019 7 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: "A few regressions and fixes for stable. Regressions: - fix a race leading to metadata space leak after task received a signal - un-deprecate 2 ioctls, marked as deprecated by mistake Fixes: - fix limit check for number of devices during chunk allocation - fix a race due to double evaluation of i_size_read inside max() macro, can cause a crash - remove wrong device id check in tree-checker" * tag 'for-5.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: un-deprecate ioctls START_SYNC and WAIT_SYNC btrfs: save i_size to avoid double evaluation of i_size_read in compress_file_range Btrfs: fix race leading to metadata space leak after task received signal btrfs: tree-checker: Fix wrong check on max devid btrfs: Consider system chunk array size for new SYSTEM chunks -
git://www.linux-watchdog.org/linux-watchdogLinus Torvalds authored
Pull watchdog fixes from Wim Van Sebroeck: - cpwd: fix build regression - pm8916_wdt: fix pretimeout registration flow - meson: Fix the wrong value of left time - imx_sc_wdt: Pretimeout should follow SCU firmware format - bd70528: Add MODULE_ALIAS to allow module auto loading * tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog: watchdog: bd70528: Add MODULE_ALIAS to allow module auto loading watchdog: imx_sc_wdt: Pretimeout should follow SCU firmware format watchdog: meson: Fix the wrong value of left time watchdog: pm8916_wdt: fix pretimeout registration flow watchdog: cpwd: fix build regression
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) BPF sample build fixes from Björn Töpel 2) Fix powerpc bpf tail call implementation, from Eric Dumazet. 3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet. 4) Fix crash in ebtables when using dnat target, from Florian Westphal. 5) Fix port disable handling whne removing bcm_sf2 driver, from Florian Fainelli. 6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski. 7) Various KCSAN fixes all over the networking, from Eric Dumazet. 8) Memory leaks in mlx5 driver, from Alex Vesker. 9) SMC interface refcounting fix, from Ursula Braun. 10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu. 11) Add a TX lock to synchonize the kTLS TX path properly with crypto operations. From Jakub Kicinski. 12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano Garzarella. 13) Infinite loop in Intel ice driver, from Colin Ian King. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits) ixgbe: need_wakeup flag might not be set for Tx i40e: need_wakeup flag might not be set for Tx igb/igc: use ktime accessors for skb->tstamp i40e: Fix for ethtool -m issue on X722 NIC iavf: initialize ITRN registers with correct values ice: fix potential infinite loop because loop counter being too small qede: fix NULL pointer deref in __qede_remove() net: fix data-race in neigh_event_send() vsock/virtio: fix sock refcnt holding during the shutdown net: ethernet: octeon_mgmt: Account for second possible VLAN header mac80211: fix station inactive_time shortly after boot net/fq_impl: Switch to kvmalloc() for memory allocation mac80211: fix ieee80211_txq_setup_flows() failure path ipv4: Fix table id reference in fib_sync_down_addr ipv6: fixes rt6_probe() and fib6_nh->last_probe init net: hns: Fix the stray netpoll locks causing deadlock in NAPI path net: usb: qmi_wwan: add support for DW5821e with eSIM support CDC-NCM: handle incomplete transfer of MTU nfc: netlink: fix double device reference drop NFC: st21nfca: fix double free ... -
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fixes from Jens Axboe: - Two NVMe device removal crash fixes, and a compat fixup for for an ioctl that was introduced in this release (Anton, Charles, Max - via Keith) - Missing error path mutex unlock for drbd (Dan) - cgroup writeback fixup on dead memcg (Tejun) - blkcg online stats print fix (Tejun) * tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block: cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead block: drbd: remove a stray unlock in __drbd_send_protocol() blkcg: make blkcg_print_stat() print stats only for online blkgs nvme: change nvme_passthru_cmd64 to explicitly mark rsvd nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths nvme-rdma: fix a segmentation fault during module unload
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Fixes 2019-11-08 This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice drivers. Colin Ian King fixes a potentially wrap-around counter in a for-loop. Nick fixes the default ITR values for the iavf driver to 50 usecs interval. Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value cannot be obtained from the firmware, so add X722 to the check to ensure the wrong value is not returned. Jake fixes igb and igc drivers in their implementation of launch time support by declaring skb->tstamp value as ktime_t instead of s64. Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may not be set for AF_XDP sockets that are only used to send packets. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Magnus Karlsson authored
The need_wakeup flag for Tx might not be set for AF_XDP sockets that are only used to send packets. This happens if there is at least one outstanding packet that has not been completed by the hardware and we get that corresponding completion (which will not generate an interrupt since interrupts are disabled in the napi poll loop) between the time we stopped processing the Tx completions and interrupts are enabled again. In this case, the need_wakeup flag will have been cleared at the end of the Tx completion processing as we believe we will get an interrupt from the outstanding completion at a later point in time. But if this completion interrupt occurs before interrupts are enable, we lose it and should at that point really have set the need_wakeup flag since there are no more outstanding completions that can generate an interrupt to continue the processing. When this happens, user space will see a Tx queue need_wakeup of 0 and skip issuing a syscall, which means will never get into the Tx processing again and we have a deadlock. This patch introduces a quick fix for this issue by just setting the need_wakeup flag for Tx to 1 all the time. I am working on a proper fix for this that will toggle the flag appropriately, but it is more challenging than I anticipated and I am afraid that this patch will not be completed before the merge window closes, therefore this easier fix for now. This fix has a negative performance impact in the range of 0% to 4%. Towards the higher end of the scale if you have driver and application on the same core and issue a lot of packets, and towards no negative impact if you use two cores, lower transmission speeds and/or a workload that also receives packets. Signed-off-by:
Magnus Karlsson <magnus.karlsson@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Magnus Karlsson authored
The need_wakeup flag for Tx might not be set for AF_XDP sockets that are only used to send packets. This happens if there is at least one outstanding packet that has not been completed by the hardware and we get that corresponding completion (which will not generate an interrupt since interrupts are disabled in the napi poll loop) between the time we stopped processing the Tx completions and interrupts are enabled again. In this case, the need_wakeup flag will have been cleared at the end of the Tx completion processing as we believe we will get an interrupt from the outstanding completion at a later point in time. But if this completion interrupt occurs before interrupts are enable, we lose it and should at that point really have set the need_wakeup flag since there are no more outstanding completions that can generate an interrupt to continue the processing. When this happens, user space will see a Tx queue need_wakeup of 0 and skip issuing a syscall, which means will never get into the Tx processing again and we have a deadlock. This patch introduces a quick fix for this issue by just setting the need_wakeup flag for Tx to 1 all the time. I am working on a proper fix for this that will toggle the flag appropriately, but it is more challenging than I anticipated and I am afraid that this patch will not be completed before the merge window closes, therefore this easier fix for now. This fix has a negative performance impact in the range of 0% to 4%. Towards the higher end of the scale if you have driver and application on the same core and issue a lot of packets, and towards no negative impact if you use two cores, lower transmission speeds and/or a workload that also receives packets. Signed-off-by:
-
