When roaming / suspending, it makes no sense to wait until
the transmit queues of the device are empty. In extreme
condition they can be starved (VO saturating the air), but
even in regular cases, it is pointless to delay the roaming
because the low level driver is trying to send packets to
an AP which is far away. We'd rather drop these packets and
let TCP retransmit if needed. This will allow to speed up
the roaming.

For suspend, the explanation is even more trivial.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Document the rfkill module parameters default_state and
master_switch_mode.
Signed-off-by: Andrew Clausen <andrew.p.clausen@gmail.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a station disconnects with frames still pending, we clear
the TIM bit, but too late - it's only cleared when the station
is already removed from the driver, and thus the driver can get
confused (and hwsim will loudly complain.)

Fix this by clearing the TIM bit earlier, when the station has
been unlinked but not removed from the driver yet. To do this,
refactor the TIM recalculation to in that case ignore traffic
and simply assume no pending traffic - this is correct for the
disconnected station even though the frames haven't been freed
yet at that point.

This patch isn't needed for current drivers though as they don't
check the station argument to the set_tim() operation and thus
don't really run into the possible confusion.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The functions called within the iterators must be called with
tasklets disabled, so use atomic iteration like the rest of
the code and disable tasklets around the whole operation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Implement the new counters cfg80211 can now advertise to userspace.
The TX code is in the sequence number handler, which is a bit odd,
but that place already knows the TID and frame type, so it was
easiest and least impact there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The base for the current statistics is pretty mixed up, support
exporting RX/TX statistics for MSDUs per TID. This (currently)
covers received MSDUs, transmitted MSDUs and retries/failures
thereof.

Doing it per TID for MSDUs makes more sense than say only per AC
because it's symmetric - we could export per-AC statistics for all
frames (which AC we used for transmission can be determined also
for management frames) but per TID is better and usually data
frames are really the ones we care about. Also, on RX we can't
determine the AC - but we do know the TID for any QoS MPDU we
received.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The current statistics we keep aren't very clear, some are on
MPDUs and some on MSDUs/MMPDUs. Clarify the descriptions based
on the counters mac80211 keeps.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add these two values:
 * BEACON_RX: number of beacons received from this peer
 * BEACON_SIGNAL_AVG: signal strength average for beacons only

These can then be used for Android Lollipop's statistics request.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
 * remove STATION_INFO_ASSOC_REQ_IES complete, but the length
   (assoc_req_ies_len) can be used instead
 * add NL80211_STA_INFO_RX_DROP_MISC which exists internally
   but not in nl80211 yet

This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.

Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.

This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use the new cfg80211_del_sta_sinfo() function to send the
statistics about the deleted station with the delete event.
This lets userspace see how much traffic etc. the deleted
station used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a station is removed, its statistics may be interesting to
userspace, for example for further aggregation of statistics of
all stations that ever connected to an AP.

Introduce a new cfg80211_del_sta_sinfo() function (and make the
cfg80211_del_sta() a static inline calling it) to allow passing
a struct station_info along with this, and send the data in the
nl80211 event message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add the time spent scanning to the survey data so it can be
reported by drivers that collect such information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Not all devices are able to report survey data (particularly
time spent for various operations) per channel. As all these
statistics already exist in survey data, allow such devices
to report them (if userspace requested it)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

All of the survey data is (currently) per channel anyway,
so having the word "channel" in the name does nothing. In
the next patch I'll introduce global data to the survey,
where the word "channel" is actually confusing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
only require headroom space. Therefore, the tailroom-needed counter can
safely be decremented for most drivers.

The older incarnation of this patch (ca34e3b5) assumed that the above
holds true for all drivers. As reported by Christopher Chavez and
researched by Christian Lamparter and Larry Finger, this isn't a valid
assumption for p54 and cw1200.

Drivers that still require tailroom for ICV/MIC even when HW encryption
is enabled can use IEEE80211_KEY_FLAG_RESERVE_TAILROOM to indicate it.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Cc: Christopher Chavez <chrischavez@gmx.us>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge mac80211.git to get some changes that would otherwise
cause conflicts with new changes coming here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The patch "40a11ca8 mac80211: check if channels allow 80 MHz for VHT
probe requests" considered disabled channels as VHT enabled, and
mistakenly sent out probe-requests with the VHT IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Put the group names into the userspace API header file so that
userspace clients can use symbolic names from there instead of
hardcoding the actual names. This doesn't really change much,
but seems somewhat cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

With the wiphy::features flag being used up this patch adds a
new field wiphy::ext_features. Considering extensibility this
new field is declared as a byte array. This extensible flag is
exposed to user-space by NL80211_ATTR_EXT_FEATURES.

Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The flag is no longer used (and hasn't been for a long time)
since trying to track authentication (and make decisions based
on state) was just causing issues all over - see commit
95de817b.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This reverts commit ca34e3b5.

It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.

Cc: stable@vger.kernel.org
Fixes: ca34e3b5 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: Christopher Chavez <chrischavez@gmx.us>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Debugged-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

dot11MulticastTransmittedFrameCount should be updated according
to the DA, which might be different from A1. Checking A1 results
in the counter being 0 in case of station, as to-DS data frames
use A1 for the BSSID.

This behaviour is defined in state machines, specifically in the
sta_tx_dcf_3.1d(10) description of 802.11-2012.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

David Binderman reports that the conditions in the first loop
are the wrong way around - checking the array contents before
the size.

Instead of leaving the empty loop there and reordering the two
checks unify it into a single loop that skips over non-matches
and exits after the first match.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

On minstrel_ht, the size of the per-sta struct is almost 18k, making it
an order-3 allocation.
A few fields inside the per-rate statistics are bigger than they need to
be. This patch reduces the size enough to cut down the per-sta struct to
about 13k (order-2 allocation).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some network cards (Intel) produce per-channel regdomains and rely on
cfg80211 to merge rules as needed. This hits the max rules limit and
fails.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

An attribute NL80211_ATTR_SOCKET_OWNER can be set by the scan initiator.
If present, the attribute will cause the scan to be stopped if the client
dies.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Because of possible races when accessing sched_scan_req pointer in
rdev, the sched_scan_req is converted to RCU pointer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If there are no interfaces up, there is no reason
to continue the reconfig flow.

The current code might end up calling driver
callbacks (e.g. resume(), reconfig_complete())
while the driver is already stopped.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The ht_oper variable is assigned a value, but never used in
ieee80211_parse_ch_switch_ie().  Remove it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit e1a0c6b3 ("mac80211: stop toggling IEEE80211_HT_CAP_SUP_WIDTH_20_40")
mistakenly removed the actual update of sta->sta.bandwidth.

Refactor ieee80211_sta_cur_vht_bw() into multiple functions
(calculate caps-bw and chandef-bw separately, and min them
with cur_max_bandwidth).

On ht chanwidth action frame set only cur_max_bandwidth
(according to the sta capabilities) and recalc the sta bw.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In beacons, handle the Country IE even if no Power Constraint IE
is present, and, capability wise, also in case that the Radio
Measurements capability is enabled.

In cases where the Country IE should be handled and that the
Power Constraint IE is not present, the Country IE alone will
set the power limit (and not both Country and Power Constraint
IEs).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

HT override configurations was ignored when choosing the channel
(until now, the override configuration affected only the
capabilities shown in the IEs).

The override configurations received only on association time,
so in this case we should determine the channel again.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When writing the code to allow per-station GTKs, I neglected to
take into account the management frame keys (index 4 and 5) when
freeing the station and only added code to free the first four
data frame keys.

Fix this by iterating the array of keys over the right length.

Cc: stable@vger.kernel.org
Fixes: e31b8213 ("cfg80211/mac80211: allow per-station GTKs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The custom-reg handling function can currently only add flags to a given
channel. This results in stale flags being left applied. In some cases
a channel was disabled and even the orig_flags were changed to reflect
this.

Previously the API was designed for a single invocation before wiphy
registration, so this didn't matter. The previous approach doesn't scale
well to self-managed regulatory devices, particularly when a more
permissive regdom is applied after a restrictive one.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If a device has self-managed regulatory, insist on returning the wiphy
specific regdomain if a wiphy-idx is specified. The global regdomain is
meaningless for such devices.

Also add an attribute for self-managed devices, so usermode can
distinguish them as such.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a new regulatory flag that allows a driver to manage regdomain
changes/updates for its own wiphy.
A self-managed wiphys only employs regulatory information obtained from
the FW and driver and does not use other cfg80211 sources like
beacon-hints, country-code IEs and hints from other devices on the same
system. Conversely, a self-managed wiphy does not share its regulatory
hints with other devices in the system. If a system contains several
devices, one or more of which are self-managed, there might be
contradictory regulatory settings between them. Usage of flag is
generally discouraged. Only use it if the FW/driver is incompatible
with non-locally originated hints.

A new API lets the driver send a complete regdomain, to be applied on
its wiphy only.

After a wiphy-specific regdomain change takes place, usermode will get
a new type of change notification. The regulatory core also takes care
enforce regulatory restrictions, in case some interfaces are on
forbidden channels.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If a wiphy-idx is specified, the kernel will return the wiphy specific
regdomain, if such exists. Otherwise return the global regdom.

When no wiphy-idx is specified, return the global regdomain as well as
all wiphy-specific regulatory domains in the system, via a new nested
list of attributes.

Add a new attribute for each wiphy-specific regdomain, for usermode to
identify it as such.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of sending peer candidate events just once, send them as long
as the peer remains in the LISTEN state in the peering state machine,
when userspace is implementing the peering manager.
Userspace may silence the events from a peer by progressing the state
machine or by setting the link state to BLOCKED.

Fixes the problem that a mesh peering process won't be fired again after
the previous first peering trial fails due to like air propagation error
if the peering is managed by user space such as wpa_supplicant.

This patch works with another patch for wpa_supplicant described here
which fires a peering process again triggered by the notice from kernel.
http://lists.shmoo.com/pipermail/hostap/2014-November/031235.htmlSigned-off-by: Kenzoh Nishikawa <Kenzoh.Nishikawa@jp.sony.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The call to cfg80211_ch_switch_notify() should be at the end of the
ieee80211_chswitch_post_beacon() function, because it should only be
sent if everything succeeded.

Fixes: d04b5ac9 ("cfg80211/mac80211: allow any interface to send channel switch notifications")
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>