GEM version in ZynqMP and most versions greater than r1p07 supports
TX and RX BD prefetch. The number of BDs that can be prefetched is a
HW configurable parameter. For ZynqMP, this parameter is 4.

When GEM DMA is accessing the last BD in the ring, even before the
BD is processed and the WRAP bit is noticed, it will have prefetched
BDs outside the BD ring. These will not be processed but it is
necessary to have accessible memory after the last BD. Especially
in cases where SMMU is used, memory locations immediately after the
last BD may not have translation tables triggering HRESP errors. Hence
always allocate extra BDs to accommodate for prefetch.
The value of tx/rx bd prefetch for any given SoC version is:
2 ^ (corresponding field in design config 10 register).
(value of this field >= 1)

Added a capability flag so that older IP versions that do not have
DCFG10 or this prefetch capability are not affected.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rx ring is allocated for all queues in macb_alloc_consistent.
Free the same for all queues instead of just Q0.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smc_release() calls a sock_put() for smc fallback sockets to cover
the passive closing sock_hold() in __smc_connect() and
smc_tcp_listen_work(). This does not make sense for sockets in state
SMC_LISTEN and SMC_INIT.
An SMC socket stays in state SMC_INIT if connect fails. The sock_put
in smc_connect_abort() does not cover all failures. Move it into
smc_connect_decline_fallback().

Fixes: ee9dfbef ("net/smc: handle sockopts forcing fallback")
Reported-by: syzbot+3a0748c8f2f210c0ef9b@syzkaller.appspotmail.com
Reported-by: syzbot+9e60d2428a42049a592a@syzkaller.appspotmail.com
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These two functions return the regular -EINVAL failure in the normal
code path, but return a nonstandard '-1' error otherwise, which gets
interpreted as -EPERM.

Let's change it to -EINVAL for the dummy functions as well.

Fixes: 4d4fd361 ("net: bridge: Publish bridge accessor functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

t4_get_flash_params() fails in a fatal fashion if the FLASH part isn't
one of the recognized parts. But this leads to desperate efforts to update
drivers when various FLASH parts which we are using suddenly become
unavailable and we need to substitute new FLASH parts.  This has lead to
more than one Customer Field Emergency when a Customer has an old driver
and suddenly can't use newly shipped adapters.

This commit fixes this by simply assuming that the FLASH part is 4MB in
size if it can't be identified. Note that all Chelsio adapters will have
flash parts which are at least 4MB in size.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: fixes in duplicate address discovery function

commit 25b0b9c4 ("tipc: handle collisions of 32-bit node address
hash values") introduced new functionality that has turned out to
contain several bugs and weaknesses.

We address those in this series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The setting of the node address is not thread safe, meaning that
two discoverers may decide to set it simultanously, with a duplicate
entry in the name table as result. We fix that with this commit.

Fixes: 25b0b9c4 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The duplicate address discovery protocol is not safe against two
discoverers running in parallel. The one executing first after the
trial period is over will set the node address and change its own
message type to DSC_REQ_MSG. The one executing last may find that the
node address is already set, and never change message type, with the
result that its links may never be established.

In this commmit we ensure that the message type always is set correctly
after the trial period is over.

Fixes: 25b0b9c4 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the duplicate address discovery protocol for tipc nodes addresses
we introduced a one second trial period before a node is allocated a
hash number to use as address.

Unfortunately, we miss to handle the case when a regular LINK REQUEST/
RESPONSE arrives from a cluster node during the trial period. Such
messages are not ignored as they should be, leading to links setup
attempts while the node still has no address.

Fixes: 25b0b9c4 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function for checking if there is an node address conflict is
supposed to return a suggestion for a new address if it finds a
conflict, and zero otherwise. But in case the peer being checked
is previously unknown it does instead return a "suggestion" for
the checked address itself. This results in a DSC_TRIAL_FAIL_MSG
being sent unecessarily to the peer, and sometimes makes the trial
period starting over again.

Fixes: 25b0b9c4 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Zapolskiy says:

====================
ravb/sh_eth: fix sleep in atomic by reusing shared ethtool handlers

For ages trivial changes to RAVB and SuperH ethernet links by means of
standard 'ethtool' trigger a 'sleeping function called from invalid
context' bug, to visualize it on r8a7795 ULCB:

  % ethtool -r eth0
  BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
  in_atomic(): 1, irqs_disabled(): 128, pid: 554, name: ethtool
  INFO: lockdep is turned off.
  irq event stamp: 0
  hardirqs last  enabled at (0): [<0000000000000000>]           (null)
  hardirqs last disabled at (0): [<ffff0000080e1d3c>] copy_process.isra.7.part.8+0x2cc/0x1918
  softirqs last  enabled at (0): [<ffff0000080e1d3c>] copy_process.isra.7.part.8+0x2cc/0x1918
  softirqs last disabled at (0): [<0000000000000000>]           (null)
  CPU: 5 PID: 554 Comm: ethtool Not tainted 4.17.0-rc4-arm64-renesas+ #33
  Hardware name: Renesas H3ULCB board based on r8a7795 ES2.0+ (DT)
  Call trace:
   dump_backtrace+0x0/0x198
   show_stack+0x24/0x30
   dump_stack+0xb8/0xf4
   ___might_sleep+0x1c8/0x1f8
   __might_sleep+0x58/0x90
   __mutex_lock+0x50/0x890
   mutex_lock_nested+0x3c/0x50
   phy_start_aneg_priv+0x38/0x180
   phy_start_aneg+0x24/0x30
   ravb_nway_reset+0x3c/0x68
   dev_ethtool+0x3dc/0x2338
   dev_ioctl+0x19c/0x490
   sock_do_ioctl+0xe0/0x238
   sock_ioctl+0x254/0x460
   do_vfs_ioctl+0xb0/0x918
   ksys_ioctl+0x50/0x80
   sys_ioctl+0x34/0x48
   __sys_trace_return+0x0/0x4

The root cause is that an attempt to modify ECMR and GECMR registers
only when RX/TX function is disabled was too overcomplicated in its
original implementation, also processing of an optional Link Change
interrupt added even more complexity, as a result the implementation
was error prone.

The new locking scheme is confirmed to be correct by dumping driver
specific and generic PHY framework function calls with aid of ftrace
while running more or less advanced tests.

Please note that sh_eth patches from the series were built-tested only.

On purpose I do not add Fixes tags, the reused PHY handlers were added
way later than the fixed problems were firstly found in the drivers.

Changes from v1 to v2:
* the original patches are split to bugfixes and enhancements only,
  both v1 and v2 series are absolutely equal in total, thus I omit
  description of changes in individual patches,
* the latter implies that there should be no strict need for retesting,
  but because formally two series are different, I have to drop the tags
  given by Geert and Andrew, please send your tags again.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic phy_ethtool_set_link_ksettings() function from phylib can
be used instead of in-house ravb_set_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic phy_ethtool_get_link_ksettings() function from phylib can be
used instead of in-house ravb_get_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy_ethtool_ksettings_get() call does not modify device state or device
driver state, hence there is no need to utilize a driver specific
spinlock.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic phy_ethtool_nway_reset() function from phylib can be used
instead of in-house ravb_nway_reset().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to call a heavyweight phy_start_aneg() for phy
auto-negotiation by ethtool, the phy is already initialized and
link auto-negotiation is started by calling phy_start() from
ravb_phy_start() when a network device is opened.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.

Since commit 35b5f6b1 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.

Now duplex mode setting is enforced in ravb_adjust_link() only, also
now RX/TX is disabled when link is put down or modifications to E-MAC
registers ECMR and GECMR are expected for both cases of checked and
ignored link status pin state from E-MAC interrupt handler.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 35b5f6b1 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.

The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic phy_ethtool_set_link_ksettings() function from phylib can
be used instead of in-house sh_eth_set_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic phy_ethtool_get_link_ksettings() function from phylib can be
used instead of in-house sh_eth_get_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy_ethtool_ksettings_get() call does not modify device state or device
driver state, hence there is no need to utilize a driver specific
spinlock.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The generic phy_ethtool_nway_reset() function from phylib can be used
instead of in-house sh_eth_nway_reset().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to call a heavyweight phy_start_aneg() for phy
auto-negotiation by ethtool, the phy is already initialized and
link auto-negotiation is started by calling phy_start() from
sh_eth_phy_start() when a network device is opened.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.

Since commit 35b5f6b1 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.

Now duplex mode setting is enforced in sh_eth_adjust_link() only,
also now RX/TX is disabled when link is put down or modifications
to E-MAC registers ECMR and GECMR are expected for both cases of
checked and ignored link status pin state from E-MAC interrupt handler.

For reference the change is a partial rework of commit 1e1b812b
("sh_eth: fix handling of no LINK signal").

Fixes: dc19e4e5 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 35b5f6b1 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.

The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.

Fixes: dc19e4e5 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The low and high values of the net.ipv4.ping_group_range sysctl were
being silently forced to the default disabled state when a write to the
sysctl contained GIDs that didn't map to the associated user namespace.
Confusingly, the sysctl's write operation would return success and then
a subsequent read of the sysctl would indicate that the low and high
values are the overflowgid.

This patch changes the behavior by clearly returning an error when the
sysctl write operation receives a GID range that doesn't map to the
associated user namespace. In such a situation, the previous value of
the sysctl is preserved and that range will be returned in a subsequent
read of the sysctl.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting up macvlan/macvtap networks over atlantic NIC results
in no traffic over these networks because ndo_set_rx_mode did
not listed UC MACs as registered in unicast filter.

Here we fix that taking into account maximum number of UC
filters supported by hardware. If more than MAX addresses were
registered, we just enable promisc  and/or allmulti to pass
the traffic in.

We also remove MULTICAST_ADDRESS_MAX constant from aq_cfg since
thats not a configurable parameter at all.

Fixes: b21f502f ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mail server hosting the old address is going to fade out.
Time to update to an address I control directly.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent. So define
a constant with (hopefully) meaningful name and pass it through
msecs_to_jiffies() to fix the HZ dependency.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
commit f21fb3ed ("Add support of Cavium Liquidio ethernet adapters")
Acked-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the USB id of LTE modem Quectel EG91. It requires the
same quirk as other Quectel modems to make it work.
Signed-off-by: Matevz Vucnik <vucnikm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arun Kumar Neelakantam says:

====================
net: qrtr: Broadcasting control messages

Allow messages only from control port to broadcast to avoid unnecessary
messages and reset the node to local router NODE ID in control messages
otherwise remote routers consider the packets as invalid and Drops it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

All the control messages broadcast to remote routers are using
QRTR_NODE_BCAST instead of using local router NODE ID which cause
the packets to be dropped on remote router due to invalid NODE ID.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The broadcast node id should only be sent with the control port id.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

At present the ipv6_renew_options_kern() function ends up calling into
access_ok() which is problematic if done from inside an interrupt as
access_ok() calls WARN_ON_IN_IRQ() on some (all?) architectures
(x86-64 is affected).  Example warning/backtrace is shown below:

 WARNING: CPU: 1 PID: 3144 at lib/usercopy.c:11 _copy_from_user+0x85/0x90
 ...
 Call Trace:
  <IRQ>
  ipv6_renew_option+0xb2/0xf0
  ipv6_renew_options+0x26a/0x340
  ipv6_renew_options_kern+0x2c/0x40
  calipso_req_setattr+0x72/0xe0
  netlbl_req_setattr+0x126/0x1b0
  selinux_netlbl_inet_conn_request+0x80/0x100
  selinux_inet_conn_request+0x6d/0xb0
  security_inet_conn_request+0x32/0x50
  tcp_conn_request+0x35f/0xe00
  ? __lock_acquire+0x250/0x16c0
  ? selinux_socket_sock_rcv_skb+0x1ae/0x210
  ? tcp_rcv_state_process+0x289/0x106b
  tcp_rcv_state_process+0x289/0x106b
  ? tcp_v6_do_rcv+0x1a7/0x3c0
  tcp_v6_do_rcv+0x1a7/0x3c0
  tcp_v6_rcv+0xc82/0xcf0
  ip6_input_finish+0x10d/0x690
  ip6_input+0x45/0x1e0
  ? ip6_rcv_finish+0x1d0/0x1d0
  ipv6_rcv+0x32b/0x880
  ? ip6_make_skb+0x1e0/0x1e0
  __netif_receive_skb_core+0x6f2/0xdf0
  ? process_backlog+0x85/0x250
  ? process_backlog+0x85/0x250
  ? process_backlog+0xec/0x250
  process_backlog+0xec/0x250
  net_rx_action+0x153/0x480
  __do_softirq+0xd9/0x4f7
  do_softirq_own_stack+0x2a/0x40
  </IRQ>
  ...

While not present in the backtrace, ipv6_renew_option() ends up calling
access_ok() via the following chain:

  access_ok()
  _copy_from_user()
  copy_from_user()
  ipv6_renew_option()

The fix presented in this patch is to perform the userspace copy
earlier in the call chain such that it is only called when the option
data is actually coming from userspace; that place is
do_ipv6_setsockopt().  Not only does this solve the problem seen in
the backtrace above, it also allows us to simplify the code quite a
bit by removing ipv6_renew_options_kern() completely.  We also take
this opportunity to cleanup ipv6_renew_options()/ipv6_renew_option()
a small amount as well.

This patch is heavily based on a rough patch by Al Viro.  I've taken
his original patch, converted a kmemdup() call in do_ipv6_setsockopt()
to a memdup_user() call, made better use of the e_inval jump target in
the same function, and cleaned up the use ipv6_renew_option() by
ipv6_renew_options().

CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If format_idx == s_mcp_trace_meta.formats_num then we read one element
beyond the end of the s_mcp_trace_meta.formats[] array.

Fixes: 50bc60cb ("qed*: Utilize FW 8.33.11.0")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Configuration information read at driver load can become stale after it is
updated. Mark information as not valid and re-populate when this happens.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.

Fixes: f3a6bd39 ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In certain conditions, the device may not be able to link in gigabit mode. This software workaround ensures that the device will not enter the failure state.

Fixes: d0cad871 ("SMSC75XX USB 2.0 Gigabit Ethernet Devices")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit b6c5734d ("sctp: fix the handling of ICMP Frag Needed
for too small MTUs"), sctp_transport_update_pmtu would refetch pathmtu
from the dst and set it to transport's pathmtu without any check.

The new pathmtu may be lower than MINSEGMENT if the dst is obsolete and
updated by .get_dst() in sctp_transport_update_pmtu. In this case, it
could have a smaller MTU as well, and thus we should validate it
against MINSEGMENT instead.

Syzbot reported a warning in sctp_mtu_payload caused by this.

This patch refetches the pathmtu by calling sctp_dst_mtu where it does
the check against MINSEGMENT.

v1->v2:
  - refetch the pathmtu by calling sctp_dst_mtu instead as Marcelo's
    suggestion.

Fixes: b6c5734d ("sctp: fix the handling of ICMP Frag Needed for too small MTUs")
Reported-by: syzbot+f0d9d7cba052f9344b03@syzkaller.appspotmail.com
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NetworkManager likes to manage linklocal prefix routes and does so with
the NLM_F_APPEND flag, breaking attempts to simplify the IPv6 route
code and by extension enable multipath routes with device only nexthops.

Revert f34436a4 and these followup patches:
6eba08c3 ("ipv6: Only emit append events for appended routes").
ce45bded ("mlxsw: spectrum_router: Align with new route replace logic")
53b562df ("mlxsw: spectrum_router: Allow appending to dev-only routes")

Update the fib_tests cases to reflect the old behavior.

Fixes: f34436a4 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: David Ahern <dsahern@gmail.com>