Apparently patchwork ended up truncating the full name.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull libnvdimm fixes from Dan Williams:

 - a fix for the persistent memory 'struct page' driver.  The
   implementation overlooked the fact that pages are allocated in 2MB
   units leading to -ENOMEM when establishing some configurations.

   It's tagged for -stable as the problem was introduced with the
   initial implementation in 4.5.

 - The new "error status translation" routine, introduced with the 4.6
   updates to the nfit driver, missed a necessary path in
   acpi_nfit_ctl().

   The end result is that we are falsely assuming commands complete
   successfully when the embedded status says otherwise.

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit: fix translation of command status results
  libnvdimm, pfn: fix memmap reservation sizing

Pull asm-generic syscall fix from Arnd Bergmann:
 "My last pull request for asm-generic had just one patch that added two
  new system calls to asm/unistd.h, but unfortunately it turned out to
  be wrong, pointing arch/tile compat mode at the native handlers rather
  than the compat ones.

  This was spotted by Yury Norov, who is working on ILP32 mode for
  arch/arm64, which would have the same problem when merged.  This fixes
  the table to use the correct compat syscalls, like the other 64-bit
  architectures do.

  I'll try to find the time to come up with a solution that prevents
  this problem from happening again, by allowing all future system calls
  to just get added in a single file for use by all architectures"

* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  asm-generic: use compat version for preadv2 and pwritev2

Pull ARM SoC fixes from Arnd Bergmann:
 "Here are a couple last-minute fixes for ARM SoCs.  Most of them are
  for the OMAP platforms, the rest are all for different platforms.

  OMAP:
     All dts fixes, mostly affecting voltages and pinctrl for various
     device drivers:

      - Regulator minimum voltage fixes for omap5
      - ISP syscon register offset fix for omap3
      - Fix regulator initial modes for n900
      - Fix omap5 pinctrl wkup instance size

  Allwinner:
     Remove incorrect constraints from a dcdc1 regulator

  Alltera SoCFPGA:
     Fix compilation in thumb2 mode

  Samsung exynos:
     Fix a potential oops in the pm-domain error handling

  Davinci:
     Avoid a link error if NVMEM is disabled

  Renesas:
     Do not mark an external uart clock as disabled, to allow probing
     the uarts"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: davinci: only use NVMEM when available
  ARM: SoCFPGA: Fix secondary CPU startup in thumb2 kernel
  ARM: dts: omap5: fix range of permitted wakeup pinmux registers
  ARM: dts: omap3-n900: Specify peripherals LDO regulators initial mode
  ARM: dts: omap3: Fix ISP syscon register offset
  ARM: dts: omap5-cm-t54: fix ldo1_reg and ldo4_reg ranges
  ARM: dts: omap5-board-common: fix ldo1_reg and ldo4_reg ranges
  arm64: dts: r8a7795: Don't disable referenced optional scif clock
  ARM: EXYNOS: Properly skip unitialized parent clock in power domain on
  ARM: dts: sun8i-q8-common: Do not set constraints on dc1sw regulator

Update my email and web addresses in the kernel maintainers file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull userns fix from Eric Biederman:
 "This contains just a single fix for a nasty oops"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  propogate_mnt: Handle the first propogated copy being a slave

Pull virtio/qemu fixes from Michael Tsirkin:
 "A couple of fixes for virtio and for the new QEMU fw cfg driver"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio: Silence uninitialized variable warning
  firmware: qemu_fw_cfg.c: potential unintialized variable

When the first propgated copy was a slave the following oops would result:
> BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
> IP: [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> PGD bacd4067 PUD bac66067 PMD 0
> Oops: 0000 [#1] SMP
> Modules linked in:
> CPU: 1 PID: 824 Comm: mount Not tainted 4.6.0-rc5userns+ #1523
> Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
> task: ffff8800bb0a8000 ti: ffff8800bac3c000 task.ti: ffff8800bac3c000
> RIP: 0010:[<ffffffff811fba4e>]  [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0
> RSP: 0018:ffff8800bac3fd38  EFLAGS: 00010283
> RAX: 0000000000000000 RBX: ffff8800bb77ec00 RCX: 0000000000000010
> RDX: 0000000000000000 RSI: ffff8800bb58c000 RDI: ffff8800bb58c480
> RBP: ffff8800bac3fd48 R08: 0000000000000001 R09: 0000000000000000
> R10: 0000000000001ca1 R11: 0000000000001c9d R12: 0000000000000000
> R13: ffff8800ba713800 R14: ffff8800bac3fda0 R15: ffff8800bb77ec00
> FS:  00007f3c0cd9b7e0(0000) GS:ffff8800bfb00000(0000) knlGS:0000000000000000
> CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> CR2: 0000000000000010 CR3: 00000000bb79d000 CR4: 00000000000006e0
> Stack:
>  ffff8800bb77ec00 0000000000000000 ffff8800bac3fd88 ffffffff811fbf85
>  ffff8800bac3fd98 ffff8800bb77f080 ffff8800ba713800 ffff8800bb262b40
>  0000000000000000 0000000000000000 ffff8800bac3fdd8 ffffffff811f1da0
> Call Trace:
>  [<ffffffff811fbf85>] propagate_mnt+0x105/0x140
>  [<ffffffff811f1da0>] attach_recursive_mnt+0x120/0x1e0
>  [<ffffffff811f1ec3>] graft_tree+0x63/0x70
>  [<ffffffff811f1f6b>] do_add_mount+0x9b/0x100
>  [<ffffffff811f2c1a>] do_mount+0x2aa/0xdf0
>  [<ffffffff8117efbe>] ? strndup_user+0x4e/0x70
>  [<ffffffff811f3a45>] SyS_mount+0x75/0xc0
>  [<ffffffff8100242b>] do_syscall_64+0x4b/0xa0
>  [<ffffffff81988f3c>] entry_SYSCALL64_slow_path+0x25/0x25
> Code: 00 00 75 ec 48 89 0d 02 22 22 01 8b 89 10 01 00 00 48 89 05 fd 21 22 01 39 8e 10 01 00 00 0f 84 e0 00 00 00 48 8b 80 d8 00 00 00 <48> 8b 50 10 48 89 05 df 21 22 01 48 89 15 d0 21 22 01 8b 53 30
> RIP  [<ffffffff811fba4e>] propagate_one+0xbe/0x1c0
>  RSP <ffff8800bac3fd38>
> CR2: 0000000000000010
> ---[ end trace 2725ecd95164f217 ]---

This oops happens with the namespace_sem held and can be triggered by
non-root users.  An all around not pleasant experience.

To avoid this scenario when finding the appropriate source mount to
copy stop the walk up the mnt_master chain when the first source mount
is encountered.

Further rewrite the walk up the last_source mnt_master chain so that
it is clear what is going on.

The reason why the first source mount is special is that it it's
mnt_parent is not a mount in the dest_mnt propagation tree, and as
such termination conditions based up on the dest_mnt mount propgation
tree do not make sense.

To avoid other kinds of confusion last_dest is not changed when
computing last_source.  last_dest is only used once in propagate_one
and that is above the point of the code being modified, so changing
the global variable is meaningless and confusing.

Cc: stable@vger.kernel.org
fixes: f2ebb3a9 ("smarter propagate_mnt()")
Reported-by: Tycho Andersen <tycho.andersen@canonical.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>

Pull input fixes from Dmitry Torokhov.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: atmel_mxt_ts - use mxt_acquire_irq in mxt_soft_reset
  Input: zforce_ts - fix dual touch recognition
  Input: twl6040-vibra - fix atomic schedule panic

Compat architectures that does not use generic unistd (mips, s390),
declare compat version in their syscall tables for preadv2 and
pwritev2. Generic unistd syscall table should do it as well.

[arnd: this initially slipped through the review and an
 incorrect patch got merged. arch/tile/ is the only architecture
 that could be affected for their 32-bit compat mode, every
 other architecture we support today is fine.]
Signed-off-by: Yury Norov <ynorov@caviumnetworks.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull IMA fix from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  ima: fix the string representation of the LSM/IMA hook enumeration ordering

Pull xen regression fixes from David Vrabel:

 - Fix two regressions causing crashes in 32-bit PV guests

 - Fix a regression in the evtchn driver

* tag 'for-linus-4.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/evtchn: fix ring resize when binding new events
  xen/balloon: Fix crash when ballooning on x86 32 bit PAE
  xen: Fix page <-> pfn conversion on 32 bit systems

The copying of ring data was wrong for two cases: For a full ring
nothing got copied at all (as in that case the canonicalized producer
and consumer indexes are identical). And in case one or both of the
canonicalized (after the resize) indexes would point into the second
half of the buffer, the copied data ended up in the wrong (free) part
of the new buffer. In both cases uninitialized data would get passed
back to the caller.

Fix this by simply copying the old ring contents twice: Once to the
low half of the new buffer, and a second time to the high half.

This addresses the inability to boot a HVM guest with 64 or more
vCPUs.  This regression was caused by 86200154 (xen/evtchn:
dynamically grow pending event channel ring).
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

This patch fixes the string representation of the LSM/IMA hook enumeration
ordering used for displaying the IMA policy.

Fixes: d9ddf077 ("ima: support for kexec image and initramfs")
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Tested-by: Eric Richter <erichte@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Merge tag 'trace-fixes-v4.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fix from Steven Rostedt:
 "Chunyu Hu noticed that if one writes into the trigger files within the
  ftrace subsystem of events that it can cause an oops.  This file is
  only writable by root, but still is a bug that needs to be fixed"

* tag 'trace-fixes-v4.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Don't display trigger file for events that can't be enabled

Pull networking fixes from David Miller:
 "Some straggler bug fixes:

   1) Batman-adv DAT must consider VLAN IDs when choosing candidate
      nodes, from Antonio Quartulli.

   2) Fix botched reference counting of vlan objects and neigh nodes in
      batman-adv, from Sven Eckelmann.

   3) netem can crash when it sees GSO packets, the fix is to segment
      then upon ->enqueue.  Fix from Neil Horman with help from Eric
      Dumazet.

   4) Fix VXLAN dependencies in mlx5 driver Kconfig, from Matthew
      Finlay.

   5) Handle VXLAN ops outside of rcu lock, via a workqueue, in mlx5,
      since it can sleep.  Fix also from Matthew Finlay.

   6) Check mdiobus_scan() return values properly in pxa168_eth and macb
      drivers.  From Sergei Shtylyov.

   7) If the netdevice doesn't support checksumming, disable
      segmentation.  From Alexandery Duyck.

   8) Fix races between RDS tcp accept and sending, from Sowmini
      Varadhan.

   9) In macb driver, probe MDIO bus before we register the netdev,
      otherwise we can try to open the device before it is really ready
      for that.  Fix from Florian Fainelli.

  10) Netlink attribute size for ILA "tunnels" not calculated properly,
      fix from Nicolas Dichtel"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  ipv6/ila: fix nlsize calculation for lwtunnel
  net: macb: Probe MDIO bus before registering netdev
  RDS: TCP: Synchronize accept() and connect() paths on t_conn_lock.
  RDS:TCP: Synchronize rds_tcp_accept_one with rds_send_xmit when resetting t_sock
  vxlan: Add checksum check to the features check function
  net: Disable segmentation if checksumming is not supported
  net: mvneta: Remove superfluous SMP function call
  macb: fix mdiobus_scan() error check
  pxa168_eth: fix mdiobus_scan() error check
  net/mlx5e: Use workqueue for vxlan ops
  net/mlx5e: Implement a mlx5e workqueue
  net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue
  net/mlx5: Unmap only the relevant IO memory mapping
  netem: Segment GSO packets on enqueue
  batman-adv: Fix reference counting of hardif_neigh_node object for neigh_node
  batman-adv: Fix reference counting of vlan object for tt_local_entry
  batman-adv: B.A.T.M.A.N V - make sure iface is reactivated upon NETDEV_UP event
  batman-adv: fix DAT candidate selection (must use vid)

Pull fuse fixes from Miklos Szeredi:
 "Fix a regression and update the MAINTAINERS entry for fuse"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: update mailing list in MAINTAINERS
  fuse: Fix return value from fuse_get_user_pages()

The handler 'ila_fill_encap_info' adds one attribute: ILA_ATTR_LOCATOR.

Fixes: 65d7ab8d ("net: Identifier Locator Addressing module")
CC: Tom Herbert <tom@herbertland.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current sequence makes us register for a network device prior to
registering and probing the MDIO bus which could lead to some unwanted
consequences, like a thread of execution calling into ndo_open before
register_netdev() returns, while the MDIO bus is not ready yet.

Rework the sequence to register for the MDIO bus, and therefore attach
to a PHY prior to calling register_netdev(), which implies reworking the
error path a bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sowmini Varadhan says:

====================
RDS: TCP: sychronization during connection startup

This patch series ensures that the passive (accept) side of the
TCP connection used for RDS-TCP is correctly synchronized with
any concurrent active (connect) attempts for a given pair of peers.

Patch 1 in the series makes sure that the t_sock in struct
rds_tcp_connection is only reset after any threads in rds_tcp_xmit
have completed (otherwise a null-ptr deref may be encountered).
Patch 2 synchronizes rds_tcp_accept_one() with the rds_tcp*connect()
path.

v2: review comments from Santosh Shilimkar, other spelling corrections
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

An arbitration scheme for duelling SYNs is implemented as part of
commit 241b2719 ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()") which ensures that both nodes
involved will arrive at the same arbitration decision. However, this
needs to be synchronized with an outgoing SYN to be generated by
rds_tcp_conn_connect(). This commit achieves the synchronization
through the t_conn_lock mutex in struct rds_tcp_connection.

The rds_conn_state is checked in rds_tcp_conn_connect() after acquiring
the t_conn_lock mutex.  A SYN is sent out only if the RDS connection is
not already UP (an UP would indicate that rds_tcp_accept_one() has
completed 3WH, so no SYN needs to be generated).

Similarly, the rds_conn_state is checked in rds_tcp_accept_one() after
acquiring the t_conn_lock mutex. The only acceptable states (to
allow continuation of the arbitration logic) are UP (i.e., outgoing SYN
was SYN-ACKed by peer after it sent us the SYN) or CONNECTING (we sent
outgoing SYN before we saw incoming SYN).
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a race condition between rds_send_xmit -> rds_tcp_xmit
and the code that deals with resolution of duelling syns added
by commit 241b2719 ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()").

Specifically, we may end up derefencing a null pointer in rds_send_xmit
if we have the interleaving sequence:
           rds_tcp_accept_one                  rds_send_xmit

                                             conn is RDS_CONN_UP, so
    					 invoke rds_tcp_xmit

                                             tc = conn->c_transport_data
        rds_tcp_restore_callbacks
            /* reset t_sock */
    					 null ptr deref from tc->t_sock

The race condition can be avoided without adding the overhead of
additional locking in the xmit path: have rds_tcp_accept_one wait
for rds_tcp_xmit threads to complete before resetting callbacks.
The synchronization can be done in the same manner as rds_conn_shutdown().
First set the rds_conn_state to something other than RDS_CONN_UP
(so that new threads cannot get into rds_tcp_xmit()), then wait for
RDS_IN_XMIT to be cleared in the conn->c_flags indicating that any
threads in rds_tcp_xmit are done.

Fixes: 241b2719 ("RDS-TCP: Reset tcp callbacks if re-using an
outgoing socket in rds_tcp_accept_one()")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
Fixes for tunnel checksum and segmentation offloads

This patch series is a subset of patches I had submitted for net-next.  I
plan to drop these two patches from the v3 of "Fix Tunnel features and
enable GSO partial for several drivers" and I am instead submitting them
for net since these are truly fixes and likely will need to be backported
to stable branches.

This series addresses 2 specific issues.  The first is that we could
request TSO on a v4 inner header while not supporting checksum offload of
the outer IPv6 header.  The second is that we could request an IPv6 inner
checksum offload without validating that we could actually support an inner
IPv6 checksum offload.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to perform an additional check on the inner headers to determine if
we can offload the checksum for them.  Previously this check didn't occur
so we would generate an invalid frame in the case of an IPv6 header
encapsulated inside of an IPv4 tunnel.  To fix this I added a secondary
check to vxlan_features_check so that we can verify that we can offload the
inner checksum.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of the mlx4 and mlx5 driver they do not support IPv6 checksum
offload for tunnels.  With this being the case we should disable GSO in
addition to the checksum offload features when we find that a device cannot
perform a checksum on a given packet type.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 3b9d6da6 ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.

Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now mdiobus_scan() returns ERR_PTR(-ENODEV) instead of NULL if the PHY
device ID was read as all ones. As this was not  an error before, this
value  should be filtered out now in this driver.

Fixes: b74766a0 ("phylib: don't return NULL from get_phy_device()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since mdiobus_scan() returns either an error code or NULL on error, the
driver should check  for both,  not only for NULL, otherwise a crash is
imminent...
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull HID fixes from Jiri Kosina:
 "Fixes for the HID subsystem:

   - regression fix for Wacom driver; commit introduced in 4.6-rc1
     mistakenly removed line that should be kept.  Fix by Ping Cheng

   - two device-specific quirks, by Ping Cheng and Nazar Mokrynskyi"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: wacom: add missed stylus_in_proximity line back
  HID: Fix boot delay for Creative SB Omni Surround 5.1 with quirk
  HID: wacom: Add support for DTK-1651

Pull clk fix from Stephen Boyd:
 "One small bug fix for the imx6qp CAN clk definition that was causing
  failures and division by zeros in the kernel on those devices"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: imx6q: fix typo in CAN clock definition

Saeed Mahameed says:

====================
Mellanox 100G mlx5 fixes for 4.6-rc

This small series provides some bug fixes for mlx5 driver.

A small bug fix for iounmap of a null pointer, which dumps a warning on some archs.

One patch to fix the VXLAN/MLX5_EN dependency issue reported by Arnd.

Two patches to fix the scheduling while atomic issue for ndo_add/del_vxlan_port
NDOs.  The first will add an internal mlx5e workqueue and the second will
delegate vxlan ports add/del requests to that workqueue.

Note: ('net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue') is only needed for net
and not net-next as the issue was globally fixed for all device drivers by:
b7aade15 ('vxlan: break dependency with netdev drivers') in net-next.

Applied on top: f27337e1 ('ip_tunnel: fix preempt warning in ip tunnel creation/updating')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The vxlan add/delete port NDOs are called under rcu lock.
The current mlx5e implementation can potentially block in these
calls, which is not allowed.  Move to using the mlx5e workqueue
to handle these NDOs.

Fixes: b3f63c3d ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement a mlx5e workqueue to handle all mlx5e specific tasks.  Move
all tasks currently using the system workqueue to the new workqueue.
This is in preparation for vxlan using the mlx5e workqueue in order to
schedule port add/remove operations.
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When MLX5_EN=y MLX5_CORE=y and VXLAN=m there is a linker error for
vxlan_get_rx_port() due to the fact that VXLAN is a module. Change Kconfig
to select VXLAN when MLX5_CORE=y. When MLX5_CORE=m there is no dependency
on the value of VXLAN.

Fixes: b3f63c3d ('net/mlx5e: Add netdev support for VXLAN tunneling')
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When freeing UAR the driver tries to unmap uar->map and uar->bf_map
which are mutually exclusive thus always unmapping a NULL pointer.
Make sure we only call iounmap() once, for the actual mapping.

Fixes: 0ba42241 ('net/mlx5: Fix global UAR mapping')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reported-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently register functions for events will be called
through the 'reg' field of event class directly without
any check when seting up triggers.

Triggers for events that don't support register through
debug fs (events under events/ftrace are for trace-cmd to
read event format, and most of them don't have a register
function except events/ftrace/functionx) can't be enabled
at all, and an oops will be hit when setting up trigger
for those events, so just not creating them is an easy way
to avoid the oops.

Link: http://lkml.kernel.org/r/1462275274-3911-1-git-send-email-chuhu@redhat.com

Cc: stable@vger.kernel.org # 3.14+
Fixes: 85f2b082 ("tracing: Add basic event trigger framework")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Commit 7e129783 ("HID: wacom: break out wacom_intuos_get_tool_type") by accident
removed stylus_in_proximity flag for Intuos series while shuffling the code
around.

Fix that by reintroducing that flag setting in wacom_intuos_inout(), where
it originally was.

Fixes: 7e129783 ("HID: wacom: break out wacom_intuos_get_tool_type")
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The fuse mailing list seems not to be open anymore.  The discussion on
fuse-devel@... is mostly userspace related anyway.

Reported-by: Andreas Gruenbacher <agruenba@redhat.com> 
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>

This was recently reported to me, and reproduced on the latest net kernel,
when attempting to run netperf from a host that had a netem qdisc attached
to the egress interface:

[  788.073771] ---------------------[ cut here ]---------------------------
[  788.096716] WARNING: at net/core/dev.c:2253 skb_warn_bad_offload+0xcd/0xda()
[  788.129521] bnx2: caps=(0x00000001801949b3, 0x0000000000000000) len=2962
data_len=0 gso_size=1448 gso_type=1 ip_summed=3
[  788.182150] Modules linked in: sch_netem kvm_amd kvm crc32_pclmul ipmi_ssif
ghash_clmulni_intel sp5100_tco amd64_edac_mod aesni_intel lrw gf128mul
glue_helper ablk_helper edac_mce_amd cryptd pcspkr sg edac_core hpilo ipmi_si
i2c_piix4 k10temp fam15h_power hpwdt ipmi_msghandler shpchp acpi_power_meter
pcc_cpufreq nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c
sd_mod crc_t10dif crct10dif_generic mgag200 syscopyarea sysfillrect sysimgblt
i2c_algo_bit drm_kms_helper ahci ata_generic pata_acpi ttm libahci
crct10dif_pclmul pata_atiixp tg3 libata crct10dif_common drm crc32c_intel ptp
serio_raw bnx2 r8169 hpsa pps_core i2c_core mii dm_mirror dm_region_hash dm_log
dm_mod
[  788.465294] CPU: 16 PID: 0 Comm: swapper/16 Tainted: G        W
------------   3.10.0-327.el7.x86_64 #1
[  788.511521] Hardware name: HP ProLiant DL385p Gen8, BIOS A28 12/17/2012
[  788.542260]  ffff880437c036b8 f7afc56532a53db9 ffff880437c03670
ffffffff816351f1
[  788.576332]  ffff880437c036a8 ffffffff8107b200 ffff880633e74200
ffff880231674000
[  788.611943]  0000000000000001 0000000000000003 0000000000000000
ffff880437c03710
[  788.647241] Call Trace:
[  788.658817]  <IRQ>  [<ffffffff816351f1>] dump_stack+0x19/0x1b
[  788.686193]  [<ffffffff8107b200>] warn_slowpath_common+0x70/0xb0
[  788.713803]  [<ffffffff8107b29c>] warn_slowpath_fmt+0x5c/0x80
[  788.741314]  [<ffffffff812f92f3>] ? ___ratelimit+0x93/0x100
[  788.767018]  [<ffffffff81637f49>] skb_warn_bad_offload+0xcd/0xda
[  788.796117]  [<ffffffff8152950c>] skb_checksum_help+0x17c/0x190
[  788.823392]  [<ffffffffa01463a1>] netem_enqueue+0x741/0x7c0 [sch_netem]
[  788.854487]  [<ffffffff8152cb58>] dev_queue_xmit+0x2a8/0x570
[  788.880870]  [<ffffffff8156ae1d>] ip_finish_output+0x53d/0x7d0
...

The problem occurs because netem is not prepared to handle GSO packets (as it
uses skb_checksum_help in its enqueue path, which cannot manipulate these
frames).

The solution I think is to simply segment the skb in a simmilar fashion to the
way we do in __dev_queue_xmit (via validate_xmit_skb), with some minor changes.
When we decide to corrupt an skb, if the frame is GSO, we segment it, corrupt
the first segment, and enqueue the remaining ones.

tested successfully by myself on the latest net kernel, to which this applies
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netem@lists.linux-foundation.org
CC: eric.dumazet@gmail.com
CC: stephen@networkplumber.org
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
In this small batch of patches you have:
- a fix for our Distributed ARP Table that makes sure that the input
  provided to the hash function during a query is the same as the one
  provided during an insert (so to prevent false negatives), by Antonio
  Quartulli
- a fix for our new protocol implementation B.A.T.M.A.N. V that ensures
  that a hard interface is properly re-activated when it is brought down
  and then up again, by Antonio Quartulli
- two fixes respectively to the reference counting of the tt_local_entry
  and neigh_node objects, by Sven Eckelmann. Such bug is rather severe
  as it would prevent the netdev objects references by batman-adv from
  being released after shutdown.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>