- 01 Dec, 2007 22 commits
-
-
Divy Le Ray authored
netif_rx_complete() should be called only when work_done < budget. Signed-off-by: Divy Le ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Divy Le Ray authored
The patch ensures that a GSO skb has enough headroom to push an encapsulating cpl_tx_pkt_lso header. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Kim Phillips authored
Extend the RGMII-Internal Delay specification case to include TX-only and RX-only variants. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Kim Phillips authored
Previously, Internal Delay specification implied the delay be applied to both TX and RX. This patch allows for separate TX/RX-only internal delay specification. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Kim Phillips authored
Allow phylib specification of cases where hardware needs to configure PHYs for Internal Delay only on either RX or TX (not both). Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
The code to change MTU doesn't correctly handle all the chip variations and requirements for restarting. On Genesis chips changing MTU would just cause receiver to hang. Use a simpler approach of just taking link down/up if needed. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
For compatiablity with sk98lin, make sure and set same values in serial mode register. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
Version for 2.6.24 Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
Need to increase TX threshold when doing Jumbo frames on dual port board to avoid underruns. (Code from sk98lin). Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
The driver would not work over fibre if other end when down then came back up (would require reloading driver). The correct way to manage the link the same way for both TP and fibre. Resloves problem described in: http://lkml.org/lkml/2007/11/6/395Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
Make sure and retry when shutting down the MAC. This code is copied from sk98lin driver. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
Receive FIFO overrun is not catastrophic condition, so don't flush when it happens. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Stephen Hemminger authored
The calculation of usable FIFO RAM is wrong in the skge driver. First, is doesn't take into account the reserved area on the original SysKonnect Genesis boards. Second it has an off-by-one error because hw->ports is either 1 or 2. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Peter Tiedemann authored
Currently ctc-device initialization is broken (kernel bug in ctc_new_device). The new network namespace code reveals a deficiency of the ctc driver. It should make use of alloc_netdev() as described in Documentation/networking/netdevices.txt. Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com> Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Sreenivasa Honnur authored
Fix the case when the card initialization fails on a mtu change and then close is called (due to ifdown), which frees non existent rx buffers. - Returning appropriate error codes in init_nic function. - In s2io_close function s2io_card_down is called only when device is up. - In s2io_change_mtu function return value of s2io_card_up function is checked and returned if it failed. Signed-off-by: Surjit Reang <surjit.reang@neterion.com> Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Jeff Garzik authored
Merge branch 'fixes-jgarzik' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
-
Jeff Garzik authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infinibandLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/ehca: Fix static rate if path faster than link IPoIB: Fix oops if xmit is called when priv->broadcast is NULL
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Fix build. [MIPS] Fix use of smp_processor_id() in preemptible code.
-
Ralf Baechle authored
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Pavel Kiryukhin authored
Freeing prom memory: 956kb freed Freeing firmware memory: 978944k freed Freeing unused kernel memory: 180k freed BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1 caller is r4k_dma_cache_wback_inv+0x144/0x2a0 Call Trace: [<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0 [<802e4b84>] debug_smp_processor_id+0xd4/0xf0 [<802e4b7c>] debug_smp_processor_id+0xcc/0xf0 ... CONFIG_DEBUG_PREEMPT is enabled. -- Bug cause is blast_dcache_range() in preemptible code [in r4k_dma_cache_wback_inv()]. blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that uses cpu_dcache_line_size(). It uses current_cpu_data that use smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT smp_processor_id emits BUG if we are executing with preemption enabled. Cpu options of cpu0 are assumed to be the superset of all processors. Can I make the same assumptions for cache line size and fix this issue the following way: Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Joachim Fenkes authored
The formula would yield -1 if the path is faster than the link, which is wrong in a bad way (max throttling). Clamp to 0, which is the correct value. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
-
- 30 Nov, 2007 11 commits
-
-
Linus Torvalds authored
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 4680/1: parentheses around NR_IRQS definition [ARM] 4679/1: AT91: Change maintainer email address [ARM] 4675/1: pxa: fix mfp address definition error for pxa320 [ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310 [ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx [ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors [ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space [ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg [ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs [ARM] uengine: fix memset size error [ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization [ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK. [ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio [ARM] 4604/2: AT91: Master clock divistor on SAM9 [ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled [ARM] PXA ssp: unlock when ssp tries to close an invalid port [ARM] 4654/1: pxa: update default MFP register value [ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h [ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition [ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
-
Matthew Wilcox authored
The database performance group have found that half the cycles spent in kmem_cache_free are spent in this one call to BUG_ON. Moving it into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a performance win of almost 0.5% on their particular benchmark. The call was added as part of commit ddc2e812 with the comment that "overhead should be minimal". It may have been minimal at the time, but it isn't now. [ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the performance regression but rather the virt_to_head_page() changes to virt_to_cache() that were added later." ] Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Joonwoo Park authored
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joonwoo Park authored
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Tomas Winkler authored
This patch fixes iwl_mac_add_interface. 1. Currently only one interface is supported, instead of silently retuning 0 now it returns -EOPNOTSUPP (By Johannes Berg) 2. It enables changing mac address from user space (By Ian Schram) Signed-off-by: Tomas Winkler <tomas@localhost.localdomain> Cc: Zhu Yi <yi.zhu@intel.com> Cc: Reinette Chatre <reinette.chatre@intel.com> Cc: linux-wireless <linux-wireless@vger.kernel.org Cc: Ian Schram <ischram@telenet.be> Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Holger Schurig authored
lbs_mac_event_disconnected() was called once and then never again upon a hardware MAC event. The reason was that the driver didn't clean the correct bit in the interrupt cause register of the chip. Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
David Woodhouse authored
I'm not sure why it was doing this, and I'm not sure I _want_ to know why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication is hence buggered. Signed-off-by: David Woodhouse <dwmw2@infradead.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Joe Perches authored
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Stefano Brivio authored
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers. Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
Saleem Abdulrasool authored
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setupLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup: x86 setup: don't recalculate ss:esp unless really necessary
-
- 29 Nov, 2007 7 commits
-
-
Russell King authored
-
Roel Kluin authored
If NR_IRQS is defined as a sum without surrounding parentheses, this may lead to problems when used in multiplications. This may lead to problems in: arch/ia64/sn/kernel/irq.c:516 arch/x86/kernel/io_apic_32.c:693, 694, 699, 700 fs/proc/proc_misc.c:464 Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
Andrew Victor authored
Change email address of AT91 maintainer. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
eric miao authored
Signed-off-by: bridge wu <bridge.wu@marvell.com> Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
eric miao authored
Some platforms (e.g. Littleton) requires LCD PCLK drive strength to be higher than default to cope with the fast PCLK frequency. Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
eric miao authored
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-
eric miao authored
Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-