- 12 Mar, 2012 2 commits
-
-
Bala Shanmugam authored
Receive background scan period as part of connect command and pass the same to the driver. Signed-off-by:
Bala Shanmugam <bkamatch@qca.qualcomm.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
Flush MCI profiles only if MCI is being actually used. This fixes a panic on driver unload when non-MCI devices are being used and btcoex_enable is set. BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffffa06296d2>] ath_mci_flush_profile+0x12/0x100 [ath9k] Call Trace: [<ffffffffa061befe>] ath9k_stop_btcoex+0x5e/0x80 [ath9k] [<ffffffffa061ed57>] ath9k_stop+0xb7/0x230 [ath9k] [<ffffffffa0533f30>] ieee80211_stop_device+0x50/0x180 [mac80211] [<ffffffffa051f0cf>] ieee80211_do_stop+0x2af/0x6a0 [mac80211] [<ffffffffa051f4da>] ieee80211_stop+0x1a/0x20 [mac80211] [<ffffffff81365d96>] __dev_close_many+0x86/0xe0 [<ffffffff81365ee0>] dev_close_many+0xa0/0x110 [<ffffffff81366038>] rollback_registered_many+0xe8/0x260 [<ffffffff813661cb>] unregister_netdevice_many+0x1b/0x80 [<ffffffffa051e950>] ieee80211_remove_interfaces+0xd0/0x110 [mac80211] [<ffffffffa050c133>] ieee80211_unregister_hw+0x53/0x120 [mac80211] [<ffffffffa061d5a4>] ath9k_deinit_device+0x44/0x70 [ath9k] [<ffffffffa062c1d4>] ath_pci_remove+0x54/0xa0 [ath9k] [<ffffffff81267c46>] pci_device_remove+0x46/0x110 [<ffffffff8131021c>] __device_release_driver+0x7c/0xe0 [<ffffffff81310960>] driver_detach+0xd0/0xe0 [<ffffffff81310078>] bus_remove_driver+0x88/0xe0 [<ffffffff81311122>] driver_unregister+0x62/0xa0 [<ffffffff81268004>] pci_unregister_driver+0x44/0xc0 [<ffffffffa062c8b5>] ath_pci_exit+0x15/0x20 [ath9k] [<ffffffffa063205d>] ath9k_exit+0x15/0x31 [ath9k] [<ffffffff810b92cc>] sys_delete_module+0x18c/0x270 [<ffffffff814373dd>] ? retint_swapgs+0x13/0x1b [<ffffffff8124828e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff81437de9>] system_call_fastpath+0x16/0x1b Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
- 09 Mar, 2012 4 commits
-
-
Wey-Yi Guy authored
BIg portion of "iwlwifi: remove max_txq_num from hw_params" was missing during merge, here is the fix for it. Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Wey-Yi Guy authored
iwlwifi: move command queue number out of the iwl_shared struct move the cmd_queue out of iwl_shared struct, but for some reason the patch is half done and fail compile Here is the fix John, could you apply this patch to wireless-next to address the issue Thanks Signed-off-by:
-
Emmanuel Grumbach authored
in iwlwifi: move setting up fw parameters Meenakshi moved code up to configure the transport layer, but this code read the sku before it was set (from the EEPROM). This killed P2P. Only the ucode_flags are needed to configure the transport layer, not the sku which _must_ be set after the EEPROM is read. We need to reconfigure the transport in case the EEPROM disabled PAN support. This is not the nicest thing to do, but we have no choice. Document that we are allowed to configure the transport several times before start_fw, but not after. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Meenakshi Venkataraman authored
The command queue number is required by the transport layer, but it can be determined only by the op mode. Move this parameter to the dvm op mode, and configure the transport layer using an API. Signed-off-by:
Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by:
-
- 08 Mar, 2012 34 commits
-
-
Amitkumar Karwar authored
In recent commit "mwifiex: correct bitrates advertised..", we have removed 22Mbps and 72Mbps bitrates from supported bitrate array. It means number of bitrates has reduced from 14 to 12. Initialize ".n_bitrates" to array size instead of hardcoding it. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Stanislav Yakovlev authored
Driver does not use it any more. Signed-off-by:
Stanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by:
-
Simon Wunderlich authored
* add entry for rate_idx_mcs_mask * fix order of entries to represent the structs' order Signed-off-by:
Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by:
-
Don Fry authored
I missed a couple of status bits in my refactoring changes. This fixes the ones I missed. Signed-off-by:
Don Fry <donald.h.fry@intel.com> Signed-off-by:
-
Johannes Berg authored
With the mac80211 deauth sequence changes, the station is deleted before the device is set unassociated. This can cause the device to get confused as it expects the station to be there while the associated bit is set. To fix this, do not delete the AP station from the device when mac80211 asks for deletion, instead just mark it as unused and rely on the unassociated RXON to drop it from the station database in the device. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
It's not needed anywhere but during init. Signed-off-by:
-
Johannes Berg authored
The only reason we ever stop/wake queues at the transport level is now that they become full (or non-full), so the messages aren't useful any more -- remove them. Signed-off-by:
-
Don Fry authored
Continue splitting the status bits between transport and op_mode. All but a few are separated. Signed-off-by:
-
Meenakshi Venkataraman authored
Gather parameters required to configure the transport layer before invoking the transport configuration API. Change-Id: I5b39da284af6d9b5432a08911b4e1173a4d7207d Signed-off-by:
-
Meenakshi Venkataraman authored
Introduce the iwl_trans_config struct which contains state variables that only the op mode can determine, but which the transport layer needs to know. Signed-off-by:
-
Emmanuel Grumbach authored
There were a few missing occurences when we get PASSIVE_NO_RX notification. Signed-off-by:
-
Stanislaw Gruszka authored
Otherwise we are not able to run more than one device per driver: [ 24.743045] kmem_cache_create: duplicate cache iwl_dev_cmd [ 24.743051] Pid: 3165, comm: NetworkManager Not tainted 3.3.0-rc2-wl+ #5 [ 24.743054] Call Trace: [ 24.743066] [<ffffffff811717d5>] kmem_cache_create+0x655/0x700 [ 24.743101] [<ffffffffa03b9f8b>] iwl_alive_notify+0x1cb/0x1f0 [iwlwifi] [ 24.743111] [<ffffffffa03ba442>] iwl_load_ucode_wait_alive+0x1b2/0x220 [iwlwifi] [ 24.743142] [<ffffffffa03ba893>] iwl_run_init_ucode+0x73/0x100 [iwlwifi] [ 24.743152] [<ffffffffa03b8fa1>] __iwl_up+0x81/0x220 [iwlwifi] [ 24.743161] [<ffffffffa03b91c0>] iwlagn_mac_start+0x80/0x190 [iwlwifi] [ 24.743188] [<ffffffffa03307b3>] ieee80211_do_open+0x293/0x770 [mac80211] Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Don Fry authored
The shared status bits are a mixture of transport and op mode bits. Some are used just by one or the other, some are shared. Begin the de-tangling of these bits. Signed-off-by:
-
David Spinadel authored
Add a Kconfig symbol to enable MFP for testing even if the firmware file doesn't advertise it. Signed-off-by:
David Spinadel <david.spinadel@intel.com> Signed-off-by:
-
Amit Beka authored
The length of iwl_rx_packet doesn't include the dword for the length itself, so add it manually. Signed-off-by:
Amit Beka <amit.beka@intel.com> Signed-off-by:
-
Amit Beka authored
Added a testmode command which tells iwl_rx_dispatch to send the RX both as a notification to nl80211 and with the registered RX handlers. This is used for monitoring RX from userspace while preserving the regular flows in the driver. Signed-off-by:
-
Stanislaw Gruszka authored
If device is disabled by rfkill switch, do not enable all interrupts, but only CSR_INT_BIT_RF_KILL to receive rfkill state change. Unblocking other interrupts might cause problems, since driver can not be prepared for receive them. Signed-off-by:
-
Stanislaw Gruszka authored
iwl_poll_direct_bit() return negative error value on timeout, positive values do not indicate an error. Signed-off-by:
-
Stanislaw Gruszka authored
That change will save us some CPU cycles at run time. Having port-based I/O seems to be not possible for PCIe devices. Signed-off-by:
-
Stanislaw Gruszka authored
wmb(), rmb() are not needed when writel(), readl() are used as accessors for MMIO. We use them indirectly via iowrite32(), ioread32(). What is needed mmiowb(), for synchronizing writes coming from different CPUs on PCIe bridge (see in patch comments). This fortunately is not needed on x86, where mmiowb() is just defined as compiler barrier. As iwlwifi devices are most likely not used on anything other than x86, this is not so important fix. Signed-off-by:
-
Stanislaw Gruszka authored
Before we write to the device registers always check if iwl_grap_nic_access() was successful. On the way change return type of grab_nic_access() to bool, and add likely()/unlikely() statement. Signed-off-by:
-
Stanislaw Gruszka authored
Print dump stack when the device is not responding. This should give some more clue about the reason of failure. Also change the message we print, since "MAC in deep sleep" is kinda confusing. On the way add unlikely(), as fail to gain NIC access is hmm ... unlikely. Signed-off-by:
-
Johannes Berg authored
In "iwlwifi: consolidate the start_device flow" the code flow changed and the firmware is now loaded by the transport layer, but the change unfortunately lost error checking -- restore. Signed-off-by:
-
Johannes Berg authored
The sensitivity parameters are never modified, so they should be const. Also remove the unused max_nrg_cck value to save some space. Signed-off-by:
-
Johannes Berg authored
There's no need to carry around the function pointer when a boolean indicating that the EEPROM stores enhanced TX power information is sufficient. Signed-off-by:
-
Johannes Berg authored
Hardware parameters will be shared, so move the definitions into the shared header file. Signed-off-by:
-
Johannes Berg authored
There's no need to have operations for these as they simply depend on whether the device has built-in bluetooth, so just duplicate the information already there (whether bt_params is present or not). Signed-off-by:
-
Johannes Berg authored
At least as long as it is called from the reclaim flow (iwlagn_check_ratid_empty) it must be atomic. Signed-off-by:
-
Johannes Berg authored
The PASSIVE_NO_RX workaround currently crosses through the op_mode and transport layers, which is a bit odd. This also isn't necessary, if the transport simply reports when queues are full (or no longer full) the op_mode can keep track of this state, and report to mac80211 only what *it* thinks is appropriate. What is appropriate can then be based on whether queues should be stopped to wait for RX or not. This significantly simplifies the transport API, it no longer needs to expose anything to stop a queue, nor to wake "any" queue, this can all be handled in the upper layer completely. Also simplify the handling to not be dependent on the context, that makes little sense as the queues are shared and both contexts have to be on the same channel anyway. Signed-off-by:
-
Johannes Berg authored
There's not much point in passing priv and hw pointers since they can be derived from each other, and the function doesn't use the hw pointer anyway. Remove it. Signed-off-by:
-
Johannes Berg authored
The dump functions never access the incoming attributes, so don't pass them. Signed-off-by:
-
Johannes Berg authored
The function never uses the priv argument as it only fills in the passed data, so remove the argument. Signed-off-by:
-
Johannes Berg authored
There's only one user, so the function can be moved into the correct file. It also loses an argument along the way. Signed-off-by:
-
Johannes Berg authored
The function never uses its conf argument, so remove it. Signed-off-by:
-
