The maximal size of the "ht_capa" file is 430 bytes.  In most cases,
it's much shorter.  Use a 512 byte long buffer.  1024 bytes is too much
and causes a warning with CONFIG_FRAME_WARN=1024.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a new regulatory hint to be used when we know all
devices have been disconnected and idle. This can happen
when we suspend, for instance. When we disconnect we can
no longer assume the same regulatory rules learned from
a country IE or beacon hints are applicable so restore
regulatory settings to an initial state.

Since driver hints are cached on the wiphy that called
the hint, those hints are not reproduced onto cfg80211
as the wiphy will respect its own wiphy->regd regardless.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When cfg80211 starts it will send a core regulatory hint. This is
sent to the global workqueue but we force processing of it by
flushing the global workqueue. The flushing was done since
cfg80211 needs last_request to always be populated.

Avoid flushing the global workqueue by processing the work
required immediately instead of putting it into a linked
list and processing it after the flush.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using stack for that causes warnings with CONFIG_FRAME_WARN=1024
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Numeric channel is hard to get, so it won't be printed.  Replace Mhz
with MHz on the affected lines and add commas as needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_power_update_mode expects to be called with mutex held, for example to
protect priv->vif. Only one caller currently does not do this, fix this.
Also, add a comment to iwl_power_update_mode to indicate this requirement.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Due to a typo, the variable contains OFDM
rates as well. The only user doesn't care,
so this change doesn't really do anything
but fix up my confusion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

auth_work, calibrated_work, update_link_led
and report_work are never used, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

There's no need to queue a work struct from
within a work struct, just move the code to
execute directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Move the waiting into iwl5000_load_section instead
of duplicating it in the caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

mac80211 will only enable powersaving for station mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Update sensitivity range values for 1000 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Update sensitivity range values for 5x00 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Update sensitivity range values for 6000 & 6x50 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

The corresponding iwl_mac_remove_interface only
acquires the mutex, leading me to believe that
the spinlock is not necessary. However, this
doesn't actually acquire the mutex around the
vif pointer check and assignment, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Change in uCode to include a unique identifier as part of sysassert,
in order to tell the difference, add the "ADVANCED SYSASSERT" description
when dump nic error to indicate the difference.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

In hostap AP mode, every time the client sends the AP
a packet the STA_NOTIFY_AWAKE code is sent from mac80211.
This results in a command being sent to the uCode even if
the client was not asleep.

The following simple patch has fixed the issue for me without any
degradation that I can find.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

IDLE PS (Full Sleep) doesn't work when ifconfig up
is done during Idle unassociated state.
Fix this by restoring FULL SLEEP in ps_restore if CONF_IDLE
is set.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the association worker requests a directed ssid scan and a bss list
already exists, the directed scan is not done. This patch corrects this
and cleans up a few typos and debug messages.
Signed-off-by: Hamish Guthrie <hamish.guthrie@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current PS3 gelic wireless driver has support for wireless
extensions. The original PS3 gelic wireless driver exposed a
dedicated API for a dedicated wpa_supplicant driver. This old
API could be enabled with CONFIG_GELIC_WIRELESS_OLD_PSK_INTERFACE,
however, as this is not being used by any distros, and it is being
removed from the driver and from wpa_supplicant.
Signed-off-by: Hamish Guthrie <hamish.guthrie@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the conversion between typedef and struct, two places that needed a "struct"
were missed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Comment text suggested by Dan Williams <dcbw@redhat.com> in
<1263952092.4481.2.camel@localhost.localdomain>.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With following patch, LED should now work with LiteOn AR5BXB63 mini
pci-e cards.

(Broken patch fixed-up by me...let's hope I did it right! -- JWL)
Signed-off-by: Luca Verdesca <magooz@salug.it>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Because DTIM information is required for powersave
but is only conveyed in beacons, wait for a beacon
before enabling powersave, and change the way the
information is conveyed to the driver accordingly.

mwl8k doesn't currently seem to implement PS but
requires the DTIM period in a different way; after
talking to Lennert we agreed to just have mwl8k do
the parsing itself in the finalize_join work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This new function (previously a static function
called just "find_ie" can be used to find a
specific IE in a buffer of IEs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Filtered frames not only need their control information
cleared to avoid wrong checks, but also need to have
jiffies and vif assigned so they can be processed or
expired.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>