- 06 Dec, 2016 5 commits
-
-
Florian Westphal authored
On SMP we overload the packet counter (unsigned long) to contain percpu offset. Hide this from callers and pass xt_counters address instead. Preparation patch to allocate the percpu counters in page-sized batch chunks. Signed-off-by:
Florian Westphal <fw@strlen.de> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Aaron Conole authored
This is to facilitate converting from a singly-linked list to an array of elements. Signed-off-by:
Aaron Conole <aconole@bytheb.org> Signed-off-by:
-
Aaron Conole authored
During nfhook traversal we only need a very small subset of nf_hook_ops members. We need: - next element - hook function to call - hook function priv argument Bridge netfilter also needs 'thresh'; can be obtained via ->orig_ops. nf_hook_entry struct is now 32 bytes on x86_64. A followup patch will turn the run-time list into an array that only stores hook functions plus their priv arguments, eliminating the ->next element. Suggested-by:
-
Aaron Conole authored
This allows easier future refactoring. Signed-off-by:
-
Florian Westphal authored
nf_defrag modules for ipv4 and ipv6 export an empty stub function. Any module that needs the defragmentation hooks registered simply 'calls' this empty function to create a phony module dependency -- modprobe will then load the defrag module too. This extends netfilter ipv4/ipv6 defragmentation modules to delay the hook registration until the functionality is requested within a network namespace instead of module load time for all namespaces. Hooks are only un-registered on module unload or when a namespace that used such defrag functionality exits. We have to use struct net for this as the register hooks can be called before netns initialization here from the ipv4/ipv6 conntrack module init path. There is no unregister functionality support, defrag will always be active once it was requested inside a net namespace. The reason is that defrag has impact on nft and iptables rulesets (without defrag we might see framents). Signed-off-by:
-
- 04 Dec, 2016 35 commits
-
-
Florian Westphal authored
This switch (default on) can be used to disable automatic registration of connection tracking functionality in newly created network namespaces. This means that when net namespace goes down (or the tracker protocol module is unloaded) we *might* have to unregister the hooks. We can either add another per-netns variable that tells if the hooks got registered by default, or, alternatively, just call the protocol _put() function and have the callee deal with a possible 'extra' put() operation that doesn't pair with a get() one. This uses the latter approach, i.e. a put() without a get has no effect. Conntrack is still enabled automatically regardless of the new sysctl setting if the new net namespace requires connection tracking, e.g. when NAT rules are created. Signed-off-by:
-
Florian Westphal authored
This makes use of nf_ct_netns_get/put added in previous patch. We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6 then implement use-count to track how many users (nft or xtables modules) have a dependency on ipv4 and/or ipv6 connection tracking functionality. When count reaches zero, the hooks are unregistered. This delays activation of connection tracking inside a namespace until stateful firewall rule or nat rule gets added. This patch breaks backwards compatibility in the sense that connection tracking won't be active anymore when the protocol tracker module is loaded. This breaks e.g. setups that ctnetlink for flow accounting and the like, without any '-m conntrack' packet filter rules. Followup patch restores old behavour and makes new delayed scheme optional via sysctl. Signed-off-by:
-
Florian Westphal authored
so that conntrack core will add the needed hooks in this namespace. Signed-off-by:
-
Florian Westphal authored
MASQUERADE, S/DNAT and REDIRECT already call functions that depend on the conntrack module. However, since the conntrack hooks are now registered in a lazy fashion (i.e., only when needed) a symbol reference is not enough. Thus, when something is added to a nat table, make sure that it will see packets by calling nf_ct_netns_get() which will register the conntrack hooks in the current netns. An alternative would be to add these dependencies to the NAT table. However, that has problems when using non-modular builds -- we might register e.g. ipv6 conntrack before its initcall has run, leading to NULL deref crashes since its per-netns storage has not yet been allocated. Adding the dependency in the modules instead has the advantage that nat table also does not register its hooks until rules are added. Signed-off-by:
-
Florian Westphal authored
currently aliased to try_module_get/_put. Will be changed in next patch when we add functions to make use of ->net argument to store usercount per l3proto tracker. This is needed to avoid registering the conntrack hooks in all netns and later only enable connection tracking in those that need conntrack. Signed-off-by:
-
Florian Westphal authored
since adf05168 ("netfilter: remove ip_conntrack* sysctl compat code") the only user (ipv4 tracker) sets this to an empty stub function. After this change nf_ct_l3proto_pernet_register() is also empty, but this will change in a followup patch to add conditional register of the hooks. Signed-off-by:
-
Davide Caratti authored
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y, connection tracking support for UDPlite protocol is built-in into nf_conntrack.ko. footprint test: $ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \ net/ipv4/netfilter/nf_conntrack_ipv4.ko \ net/ipv6/netfilter/nf_conntrack_ipv6.ko (builtin)|| udplite| ipv4 | ipv6 |nf_conntrack ---------++--------+--------+--------+-------------- none || 432538 | 828755 | 828676 | 6141434 UDPlite || - | 829649 | 829362 | 6498204 Signed-off-by:Davide Caratti <dcaratti@redhat.com> Signed-off-by:
-
Davide Caratti authored
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection tracking support for SCTP protocol is built-in into nf_conntrack.ko. footprint test: $ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \ net/ipv4/netfilter/nf_conntrack_ipv4.ko \ net/ipv6/netfilter/nf_conntrack_ipv6.ko (builtin)|| sctp | ipv4 | ipv6 | nf_conntrack ---------++--------+--------+--------+-------------- none || 498243 | 828755 | 828676 | 6141434 SCTP || - | 829254 | 829175 | 6547872 Signed-off-by: -
Davide Caratti authored
CONFIG_NF_CT_PROTO_DCCP is no more a tristate. When set to y, connection tracking support for DCCP protocol is built-in into nf_conntrack.ko. footprint test: $ ls -l net/netfilter/nf_conntrack{_proto_dccp,}.ko \ net/ipv4/netfilter/nf_conntrack_ipv4.ko \ net/ipv6/netfilter/nf_conntrack_ipv6.ko (builtin)|| dccp | ipv4 | ipv6 | nf_conntrack ---------++--------+--------+--------+-------------- none || 469140 | 828755 | 828676 | 6141434 DCCP || - | 830566 | 829935 | 6533526 Signed-off-by: -
Davide Caratti authored
To allow usage of enum ip_conntrack_dir in include/net/netns/conntrack.h, this patch encloses #include <linux/netfilter.h> in a #ifndef __KERNEL__ directive, so that compiler errors caused by unwanted inclusion of include/linux/netfilter.h are avoided. In addition, #include <linux/netfilter/nf_conntrack_common.h> line has been added to resolve correctly CTINFO2DIR macro. Signed-off-by:
Mikko Rapeli <mikko.rapeli@iki.fi> Signed-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-nextPablo Neira Ayuso authored
Simon Horman says: ==================== IPVS Updates for v4.10 please consider these enhancements to the IPVS for v4.10. * Decrement the IP ttl in all the modes in order to prevent infinite route loops. Thanks to Dwip Banerjee. * Use IS_ERR_OR_NULL macro. Clean-up from Gao Feng. ==================== Signed-off-by: -
Liping Zhang authored
So we can autoload nfnetlink_log.ko when the user adding nft log group X rule in netdev family. Signed-off-by:
Liping Zhang <zlpnobody@gmail.com> Signed-off-by:
-
Liping Zhang authored
In netdev family, we will handle non ethernet packets, so using eth_hdr(skb)->h_proto is incorrect. Meanwhile, we can use socket(AF_PACKET...) to sending packets, so skb->protocol is not always set in bridge family. Add an extra parameter into nf_log_l2packet to solve this issue. Fixes: 1fddf4ba ("netfilter: nf_log: add packet logging for netdev family") Signed-off-by:
-
Davide Caratti authored
CONFIG_NF_NAT_PROTO_UDPLITE is no more a tristate. When set to y, NAT support for UDPlite protocol is built-in into nf_nat.ko. footprint test: (nf_nat_proto_) |udplite || nf_nat --------------------------+--------++-------- no builtin | 408048 || 2241312 UDPLITE builtin | - || 2577256 Signed-off-by:
-
Davide Caratti authored
CONFIG_NF_NAT_PROTO_SCTP is no more a tristate. When set to y, NAT support for SCTP protocol is built-in into nf_nat.ko. footprint test: (nf_nat_proto_) | sctp || nf_nat --------------------------+--------++-------- no builtin | 428344 || 2241312 SCTP builtin | - || 2597032 Signed-off-by:
-
Davide Caratti authored
CONFIG_NF_NAT_PROTO_DCCP is no more a tristate. When set to y, NAT support for DCCP protocol is built-in into nf_nat.ko. footprint test: (nf_nat_proto_) | dccp || nf_nat --------------------------+--------++-------- no builtin | 409800 || 2241312 DCCP builtin | - || 2578968 Signed-off-by:
-
Arturo Borrero Gonzalez authored
The email address has changed, let's update the copyright statements. Signed-off-by:
Arturo Borrero Gonzalez <arturo@debian.org> Signed-off-by:
-
Erik Nordmark authored
Implemented RFC7527 Enhanced DAD. IPv6 duplicate address detection can fail if there is some temporary loopback of Ethernet frames. RFC7527 solves this by including a random nonce in the NS messages used for DAD, and if an NS is received with the same nonce it is assumed to be a looped back DAD probe and is ignored. RFC7527 is enabled by default. Can be disabled by setting both of conf/{all,interface}/enhanced_dad to zero. Signed-off-by:Erik Nordmark <nordmark@arista.com> Signed-off-by:
Bob Gilligan <gilligan@arista.com> Reviewed-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Andrew Lunn says: ==================== mv88e6390 batch 3 More patches to support the MV88e6390. This is mostly refactoring existing code and adding implementations for the mv88e6390. This patchset set which reserved frames are sent to the cpu, the size of jumbo frames that will be accepted, turn off egress rate limiting, and configuration of pause frames. ==================== Signed-off-by: -
Andrew Lunn authored
The mv88e6390 has a number flow control registers accessed via the Flow Control register. Use these to set the pause control. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
The mv88e6390 has a different mechanism for configuring pause. Refactor the code into an ops function, and for the moment, don't add any mv88e6390 code yet. Signed-off-by:
-
Andrew Lunn authored
There are two different rate limiting configurations, depending on the switch generation. Refactor this into ops. Signed-off-by:
-
Andrew Lunn authored
Some switches support jumbo frames. Refactor this code into operations in the ops structure. Signed-off-by:
-
Andrew Lunn authored
Older devices have a couple of registers in global2. The mv88e6390 family has a single register in global1 behind which hides similar configuration. Implement and op for this. Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== MV88E6390 batch two This is the second batch of patches adding support for the MV88e6390. They are not sufficient to make it work properly. The mv88e6390 has a much expanded set of priority maps. Refactor the existing code, and implement basic support for the new device. Similarly, the monitor control register has been reworked. The mv88e6390 has something odd in its EDSA tagging implementation, which means it is not possible to use it. So we need to use DSA tagging. This is the first device with EDSA support where we need to use DSA, and the code does not support this. So two patches refactor the existing code. The two different register definitions are separated out, and using DSA on an EDSA capable device is added. v2: Add port prefix Add helper function for 6390 Add _IEEE_ into #defines Split monitor_ctrl into a number of separate ops. Remove 6390 code which is management, used in a later patch s/EGREES/EGRESS/. Broke up setup_port_dsa() and set_port_dsa() into a number of ops v3: Verify mandatory ops for port setup Don't set ether type for DSA port. ==================== Signed-off-by: -
Andrew Lunn authored
Older chips only support DSA tagging. Newer chips have both DSA and EDSA tagging. Refactor the code by adding port functions for setting the frame mode, egress mode, and if to forward unknown frames. This results in the helper mv88e6xxx_6065_family() becoming unused, so remove it. Signed-off-by:
-
Andrew Lunn authored
Older chips support a single tagging protocol, DSA. New chips support both DSA and EDSA, an enhanced version. Having both as an option changes the register layouts. Up until now, it has been assumed that if EDSA is supported, it will be used. Hence the register layout has been determined by which protocol should be used. However, mv88e6390 has a different implementation of EDSA, which requires we need to use the DSA tagging. Hence separate the selection of the protocol from the register layout. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
Andrew Lunn authored
The mv88e6390 changes the monitor control register into the Monitor and Management control, which is an indirection register to various registers. Add ops to set the CPU port and the ingress/egress port for both register layouts, to global1 Signed-off-by:
-
Andrew Lunn authored
The mv88e6390 does not have the two registers to set the frame priority map. Instead it has an indirection registers for setting a number of different priority maps. Refactor the old code into an function, implement the mv88e6390 version, and use an op to call the right one. Signed-off-by:
-
David S. Miller authored
Jiri Pirko says: ==================== ipv4: fib: Replay events when registering FIB notifier Ido says: In kernel 4.9 the switchdev-specific FIB offload mechanism was replaced by a new FIB notification chain to which modules could register in order to be notified about the addition and deletion of FIB entries. The motivation for this change was that switchdev drivers need to be able to reflect the entire FIB table and not only FIBs configured on top of the port netdevs themselves. This is useful in case of in-band management. The fundamental problem with this approach is that upon registration listeners lose all the information previously sent in the chain and thus have an incomplete view of the FIB tables, which can result in packet loss. This patchset fixes that by dumping the FIB tables and replaying notifications previously sent in the chain for the registered notification block. The entire dump process is done under RCU and thus the FIB notification chain is converted to be atomic. The listeners are modified accordingly. This is done in the first eight patches. The ninth patch adds a change sequence counter to ensure the integrity of the FIB dump. The last patch adds the dump itself to the FIB chain registration function and modifies existing listeners to pass a callback to be executed in case dump was inconsistent. --- v3->v4: - Register the notification block after the dump and protect it using the change sequence counter (Hannes Frederic Sowa). - Since we now integrate the dump into the registration function, drop the sysctl to set maximum number of retries and instead set it to a fixed number. Lets see if it's really a problem before adding something we can never remove. - For the same reason, dump FIB tables for all net namespaces. - Add a comment regarding guarantees provided by mutex semantics. v2->v3: - Add sysctl to set the number of FIB dump retries (Hannes Frederic Sowa). - Read the sequence counter under RTNL to ensure synchronization between the dump process and other processes changing the routing tables (Hannes Frederic Sowa). - Pass a callback to the dump function to be executed prior to a retry. - Limit the dump to a single net namespace. v1->v2: - Add a sequence counter to ensure the integrity of the FIB dump (David S. Miller, Hannes Frederic Sowa). - Protect notifications from re-ordering in listeners by using an ordered workqueue (Hannes Frederic Sowa). - Introduce fib_info_hold() (Jiri Pirko). - Relieve rocker from the need to invoke the FIB dump by registering to the FIB notification chain prior to ports creation. ==================== Signed-off-by: -
Ido Schimmel authored
Commit b90eb754 ("fib: introduce FIB notification infrastructure") introduced a new notification chain to notify listeners (f.e., switchdev drivers) about addition and deletion of routes. However, upon registration to the chain the FIB tables can already be populated, which means potential listeners will have an incomplete view of the tables. Solve that by dumping the FIB tables and replaying the events to the passed notification block. The dump itself is done using RCU in order not to starve consumers that need RTNL to make progress. The integrity of the dump is ensured by reading the FIB change sequence counter before and after the dump under RTNL. This allows us to avoid the problematic situation in which the dumping process sends a ENTRY_ADD notification following ENTRY_DEL generated by another process holding RTNL. Callers of the registration function may pass a callback that is executed in case the dump was inconsistent with current FIB tables. The number of retries until a consistent dump is achieved is set to a fixed number to prevent callers from looping for long periods of time. In case current limit proves to be problematic in the future, it can be easily converted to be configurable using a sysctl. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
The next patch will enable listeners of the FIB notification chain to request a dump of the FIB tables. However, since RTNL isn't taken during the dump, it's possible for the FIB tables to change mid-dump, which will result in inconsistency between the listener's table and the kernel's. Allow listeners to know about changes that occurred mid-dump, by adding a change sequence counter to each net namespace. The counter is incremented just before a notification is sent in the FIB chain. Signed-off-by:
-
Ido Schimmel authored
In order not to hold RTNL for long periods of time we're going to dump the FIB tables using RCU. Convert the FIB notification chain to be atomic, as we can't block in RCU critical sections. Signed-off-by:
-
Ido Schimmel authored
We can miss FIB notifications sent between the time the ports were created and the FIB notification block registered. Instead of receiving these notifications only when they are replayed for the FIB notification block during registration, just register the notification block before the ports are created. Signed-off-by:
-
Ido Schimmel authored
Convert rocker to offload FIBs in deferred work in a similar fashion to mlxsw, which was converted in the previous commits. Signed-off-by:
-
