Pull arm64 fixes from Catalin Marinas:

 - #ifdef CONFIG_EFI around __efi_fpsimd_begin/end

 - Assembly code alignment reduced to 4 bytes from 16

 - Ensure the kernel is compiled for LP64 (there are some arm64
   compilers around defaulting to ILP32)

 - Fix arm_pmu_acpi memory leak on the error path

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  drivers/perf: arm_pmu_acpi: Release memory obtained by kasprintf
  arm64: ensure the kernel is compiled for LP64
  arm64: relax assembly code alignment from 16 byte to 4 byte
  arm64: efi: Don't include EFI fpsimd save/restore code in non-EFI kernels

Some architectures define the no-op macros/functions copy_segments,
release_segments and forget_segments. These are used nowhere in the
tree, so removed them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Vineet Gupta <vgupta@synopsys.com>   [for arch/arc]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull xen fixes from Juergen Gross:
 "A fix for a missing __init annotation and two cleanup patches"

* tag 'for-linus-4.14b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen, arm64: drop dummy lookup_address()
  xen: don't compile pv-specific parts if XEN_PV isn't configured
  xen: x86: mark xen_find_pt_base as __init

Pull powerpc fixes from Michael Ellerman:
 "It turns out our single-fix pull from last week was too good to be
  true. I missed a few fixes in that pull that had already come in
  because I was on leave, but also we hadn't found the bugs yet. So this
  week it's a bit bigger, though not ridiculous. Hopefully things will
  settle down from here on.

  Four fixes for the new instruction emulation code. A fix for CPU
  offline on bare metal machines when certain idle states are not
  supported, and a fix for a device_node refcounting oops during CPU
  hotplug, caused by recent changes.

  Going to stable are a fix for an oops during core dump on machines
  that have TM (Transactional Memory) disabled. Reordering some EEH
  initialisation to avoid trashing memory, and another device_node
  refcounting fix.

  And a few other minor things.

 Thanks to: Anton Blanchard, Benjamin Herrenschmidt, Cyril Bur, Gautham
 R. Shenoy, Gustavo Romero, Kamalesh Babulal, Matthew Weber, Matt Weber,
 Naveen N. Rao, Nicholas Piggin, Pavithra Prakash, Ravi Bangoria, Ronak
 Desai, Scott Wood, Tyrel Datwyler"

* tag 'powerpc-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Fix parent_dn reference leak in add_dt_node()
  powerpc/pseries: Fix "OF: ERROR: Bad of_node_put() on /cpus" during DLPAR
  powerpc/eeh: Create PHB PEs after EEH is initialized
  powerpc/kprobes: Update optprobes to use emulate_update_regs()
  powerpc/powernv: Clear LPCR[PECE1] via stop-api only for deep state offline
  powerpc/sstep: mullw should calculate a 64 bit signed result
  powerpc/sstep: Fix issues with mcrf
  powerpc/sstep: Fix issues with set_cr0()
  powerpc/tm: Flush TM only if CPU has TM feature
  powerpc/sysrq: Fix oops whem ppmu is not registered
  powerpc/configs: Update for CONFIG_SND changes
  powerpc/e6500: Update machine check for L1D cache err

Pull MIPS fixes from Ralf Baechle:

 - Fix a build error on MSP71xx which used to rely on somehow magically
   <asm/setup.h> being pulled in which no longer happens.

 - Fix the __write_64bit_c0_split inline assembler where there was the
   theoretical possibility of GCC interpret the constraints such that
   bad code could result.

 - A __init was causing section mismatch errors on Alchemy. Just to be
   on the safe side, Manuel's patch does away with all of them.

 - Fix perf event init.

* '4.14-fixes' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: PCI: fix pcibios_map_irq section mismatch
  MIPS: Fix input modify in __write_64bit_c0_split()
  MIPS: MSP71xx: Include asm/setup.h
  MIPS: Fix perf event init

Pull s390 fixes from Martin Schwidefsky:

 - A couple of bug fixes: memory management, perf, cio, dasd and
   scm_blk.

 - A larger change in regard to the CPU topology to improve performance
   for systems running under z/VM or KVM.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/topology: enable / disable topology dynamically
  s390/topology: alternative topology for topology-less machines
  s390/mm: fix write access check in gup_huge_pmd()
  s390/mm: make pmdp_invalidate() do invalidation only
  s390/cio: recover from bad paths
  s390/scm_blk: consistently use blk_status_t as error type
  s390/dasd: fix race during dasd initialization
  s390/perf: fix bug when creating per-thread event

Pull crypto fixes from Herbert Xu:
 - Fix compiler warnings in inside-secure
 - Fix LS1021A support in caam
 - Avoid using RBP in x86 crypto code
 - Fix bug in talitos that prevents hashing with algif
 - Fix bugs talitos hashing code that cause incorrect hash result
 - Fix memory freeing path bug in drbg
 - Fix af_alg crash when two SG lists are chained

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: af_alg - update correct dst SGL entry
  crypto: caam - fix LS1021A support on ARMv7 multiplatform kernel
  crypto: inside-secure - fix gcc-4.9 warnings
  crypto: talitos - Don't provide setkey for non hmac hashing algs
  crypto: talitos - fix hashing
  crypto: talitos - fix sha224
  crypto: x86/twofish - Fix RBP usage
  crypto: sha512-avx2 - Fix RBP usage
  crypto: x86/sha256-ssse3 - Fix RBP usage
  crypto: x86/sha256-avx2 - Fix RBP usage
  crypto: x86/sha256-avx - Fix RBP usage
  crypto: x86/sha1-ssse3 - Fix RBP usage
  crypto: x86/sha1-avx2 - Fix RBP usage
  crypto: x86/des3_ede - Fix RBP usage
  crypto: x86/cast6 - Fix RBP usage
  crypto: x86/cast5 - Fix RBP usage
  crypto: x86/camellia - Fix RBP usage
  crypto: x86/blowfish - Fix RBP usage
  crypto: drbg - fix freeing of resources

Free memory region, if arm_pmu_acpi_probe is not successful.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull libnvdimm fixes from Dan Williams:
 "A crash fix and corresponding regression test enabling for the crash
  scenario. The unit test for this crash is available in ndctl-v58.2.

  This branch has received a build success notification from the
  0day-kbuild robot over 148 configs. The fix is tagged for -stable /
  backport to 4.13"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, namespace: fix btt claim class crash
  tools/testing/nvdimm: disable labels for nfit_test.1

Merge tag 'kbuild-fixes-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:
 "Here are some early Kbuild fixes.

  The in-kernel firmware was removed during the previous merge window.
  Since then, some bug reports of broken rpm building are flying in ML.
  We need to fix it now.

  Summary:

   - remove firmware install from rpm-pkg / deb-pkg

   - fix mismatch between release number and UTS_VERSION for rpm-pkg"

* tag 'kbuild-fixes-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: rpm-pkg: fix version number handling
  kbuild: deb-pkg: remove firmware package support
  kbuild: rpm-pkg: delete firmware_install to fix build error

Pull misc fixes from Al Viro:
 "A couple of regression fixes, one for this merge window, one for the
  previous cycle"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ipc/shm: Fix order of parameters when calling copy_compat_shmid_to_user
  iov_iter: fix page_copy_sane for compound pages

Pull mtd fixes from Boris Brezillon:
 "SPI NOR:
   - Fix the SFDP parsing code (bugs reported by Geert Uytterhoeven)

  NAND:
   - Fix a resource leak in the lpc32xx_mlc driver
   - Fix a build warning in the core"

* tag 'mtd/fixes-for-4.14-rc2' of git://git.infradead.org/linux-mtd:
  mtd: nand: remove unused blockmask variable
  mtd: nand: lpc32xx_mlc: Fix an error handling path in lpc32xx_nand_probe()
  mtd: spi-nor: fix DMA unsafe buffer issue in spi_nor_read_sfdp()
  mtd: spi-nor: Check consistency of the memory size extracted from the SFDP

Pull drm fixes from Dave Airlie:
 "amdkfd, i915 and exynos fixes.

  I've ended up on unplanned + planned leave this week, but there were
  some fixes I decided to dequeue, some amdkfd bits missed the next pull
  but they are pretty trivial, so I included them.

  I'm not sure I'll see much else for rc2, lots of people are at XDC"

* tag 'drm-fixes-for-v4.14-rc2' of git://people.freedesktop.org/~airlied/linux:
  drm/exynos/hdmi: Fix unsafe list iteration
  drm: exynos: include linux/irq.h
  drm/exynos: Fix suspend/resume support
  drm/exynos: Fix locking in the suspend/resume paths
  drm/i915: Remove unused 'in_vbl' from i915_get_crtc_scanoutpos()
  drm/i915/cnp: set min brightness from VBT
  Revert "drm/i915/bxt: Disable device ready before shutdown command"
  drm/i915/bxt: set min brightness from VBT
  drm/i915: Fix an error handling in 'intel_framebuffer_init()'
  drm/i915/gvt: Fix incorrect PCI BARs reporting
  drm/amdkfd: pass queue's mqd when destroying mqd
  drm/amdkfd: remove memset before memcpy
  uapi linux/kfd_ioctl.h: only use __u32 and __u64

Pull dma mapping fix from Christoph Hellwig:
 "A fix for a fix that went in this merge window from Arnd"

* tag 'dma-mapping-4.14-2' of git://git.infradead.org/users/hch/dma-mapping:
  dma-coherent: fix rmem_dma_device_init regression

Drop  the __init from pcibios_map_irq() to make this section mis-
match go away:

WARNING: vmlinux.o(.text+0x56acd4): Section mismatch in reference from the function pcibios_scanbus() to the function .init.text:pcibios_map_irq()
The function pcibios_scanbus() references
the function __init pcibios_map_irq().
This is often because pcibios_scanbus lacks a __init
annotation or the annotation of pcibios_map_irq is wrong.

Run-Tested only on Alchemy.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17267/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The inline asm in __write_64bit_c0_split() modifies the 64-bit input
operand by shifting the high register left by 32, and constructing the
full 64-bit value in the low register (even on a 32-bit kernel), so if
that value is used again it could cause breakage as GCC would assume the
registers haven't changed when they have.

To quote the GCC extended asm documentation:
> Warning: Do not modify the contents of input-only operands (except for
> inputs tied to outputs). The compiler assumes that on exit from the
> asm statement these operands contain the same values as they had
> before executing the statement.

Avoid modifying the input by using a temporary variable as an output
which is modified instead of the input and not otherwise used. The asm
is always __volatile__ so GCC shouldn't optimise it out. The low
register of the temporary output is written before the high register of
the input is read, so we have two constraint alternatives, one where
both use the same registers (for when the input value isn't subsequently
used), and one with an early clobber on the output in case the low
output uses the same register as the high input. This allows the
resulting assembly to remain mostly unchanged.

A diff of a MIPS32r6 kernel reveals only three differences, two in
relation to write_c0_r10k_diag() in cpu_probe() (register allocation
rearranged slightly but otherwise identical), and one in relation to
write_c0_cvmmemctl2() in kvm_vz_local_flush_guesttlb_all(), but the
octeon CPU is only supported on 64-bit kernels where
__write_64bit_c0_split() isn't used so that shouldn't matter in
practice. So there currently doesn't appear to be anything broken by
this bug.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17315/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

msp71xx_defconfig can not be built at the in v4.14-rc1

arch/mips/pmcs-msp71xx/msp_smp.c:72:2: error: implicit declaration of function 'set_vi_handler' [-Werror=implicit-function-declaration]

I don't know what caused the regression, but including the right
header is the obvious fix.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17309/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

A reference to the parent device node is held by add_dt_node() for the
node to be added. If the call to dlpar_configure_connector() fails
add_dt_node() returns ENOENT and that reference is not freed.

Add a call to of_node_put(parent_dn) prior to bailing out after a
failed dlpar_configure_connector() call.

Fixes: 8d5ff320 ("powerpc/pseries: Make dlpar_configure_connector parent node aware")
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 215ee763 ("powerpc: pseries: remove dlpar_attach_node
dependency on full path") reworked dlpar_attach_node() to no longer
look up the parent node "/cpus", but instead to have the parent node
passed by the caller in the function parameter list.

As a result dlpar_attach_node() is no longer responsible for freeing
the reference to the parent node. However, commit 215ee763 failed
to remove the of_node_put(parent) call in dlpar_attach_node(), or to
take into account that the reference to the parent in the caller
dlpar_cpu_add() needs to be held until after dlpar_attach_node()
returns.

As a result doing repeated cpu add/remove dlpar operations will
eventually result in the following error:

  OF: ERROR: Bad of_node_put() on /cpus
  CPU: 0 PID: 10896 Comm: drmgr Not tainted 4.13.0-autotest #1
  Call Trace:
   dump_stack+0x15c/0x1f8 (unreliable)
   of_node_release+0x1a4/0x1c0
   kobject_put+0x1a8/0x310
   kobject_del+0xbc/0xf0
   __of_detach_node_sysfs+0x144/0x210
   of_detach_node+0xf0/0x180
   dlpar_detach_node+0xc4/0x120
   dlpar_cpu_remove+0x280/0x560
   dlpar_cpu_release+0xbc/0x1b0
   arch_cpu_release+0x6c/0xb0
   cpu_release_store+0xa0/0x100
   dev_attr_store+0x68/0xa0
   sysfs_kf_write+0xa8/0xf0
   kernfs_fop_write+0x2cc/0x400
   __vfs_write+0x5c/0x340
   vfs_write+0x1a8/0x3d0
   SyS_write+0xa8/0x1a0
   system_call+0x58/0x6c

Fix the issue by removing the of_node_put(parent) call from
dlpar_attach_node(), and ensuring that the reference to the parent
node is properly held and released by the caller dlpar_cpu_add().

Fixes: 215ee763 ("powerpc: pseries: remove dlpar_attach_node dependency on full path")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
[mpe: Add a comment in the code and frob the change log slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Otherwise we end up not yet having computed the right diag data size
on powernv where EEH initialization is delayed, thus causing memory
corruption later on when calling OPAL.

Fixes: 5cb1f8fd ("powerpc/powernv/pci: Dynamically allocate PHB diag data")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 553f770e ("ipc: move compat shmctl to native") moved the
compat IPC syscall handling into ipc/shm.c and refactored the struct
accessors in the process. Unfortunately, the call to
copy_compat_shmid_to_user when handling a compat {IPC,SHM}_STAT command
gets the arguments the wrong way round, passing a kernel stack address
as the user buffer (destination) and the user buffer as the kernel stack
address (source).

This patch fixes the parameter ordering so the buffers are accessed
correctly.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Issue is that if the data crosses a page boundary inside a compound
page, this check will incorrectly trigger a WARN_ON.

To fix this, compute the order using the head of the compound page and
adjust the offset to be relative to that head.

Fixes: 72e809ed ("iov_iter: sanity checks for copy to/from page
primitives")
Signed-off-by: Petar Penkov <ppenkov@google.com>
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge tag 'exynos-drm-fixes-for-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes

- fix suspend/resume issues.
- fix memory corruption detected by kasan.
- fix build error on x86.

* tag 'exynos-drm-fixes-for-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos/hdmi: Fix unsafe list iteration
  drm: exynos: include linux/irq.h
  drm/exynos: Fix suspend/resume support
  drm/exynos: Fix locking in the suspend/resume paths

Merge tag 'drm-intel-fixes-2017-09-20' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes

drm/i915 fixes for 4.14-rc1

Couple fixes for stable:

- Fix MIPI panels on BXT.
- Fix PCI BARs information on GVT.

Plus other fixes:

- Fix minimal brightness for BXT, GLK, CFL and CNL.
- Fix compilation warning: unused in_vbl
- Fix error handling in intel_framebuffer_init

* tag 'drm-intel-fixes-2017-09-20' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915: Remove unused 'in_vbl' from i915_get_crtc_scanoutpos()
  drm/i915/cnp: set min brightness from VBT
  Revert "drm/i915/bxt: Disable device ready before shutdown command"
  drm/i915/bxt: set min brightness from VBT
  drm/i915: Fix an error handling in 'intel_framebuffer_init()'
  drm/i915/gvt: Fix incorrect PCI BARs reporting

Pull tracing fixes from Steven Rostedt:
 "This includes three minor fixes.

    - Have writing to trace file clear the irqsoff (and friends) tracer

    - trace_pipe behavior for instance buffers was different than top
      buffer

    - Show a message of why mmiotrace doesn't start from commandline"

* tag 'trace-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix trace_pipe behavior for instance traces
  tracing: Ignore mmiotrace from kernel commandline
  tracing: Erase irqsoff trace with empty write

The "Release:" field of the spec file is determined based on the
.version file.

However, the .version file is not copied to the source tar file.
So, when we build the kernel from the source package, the UTS_VERSION
always indicates #1.  This does not match with "rpm -q".

The kernel UTS_VERSION and "rpm -q" do not agree for binrpm-pkg, either.
Please note the kernel has already been built before the spec file is
created.  Currently, mkspec invokes mkversion.  This script returns an
incremented version.  So, the "Release:" field of the spec file is
greater than the version in the kernel by one.

For the source package build (where .version file is missing), we can
give KBUILD_BUILD_VERSION=%{release} to the build command.

For the binary package build, we can simply read out the .version file
because it contains the version number that was used for building the
kernel image.

We can remove scripts/mkversion because scripts/package/Makefile need
not touch the .version file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Commit 5620a0d1 ("firmware: delete in-kernel firmware") deleted
in-kernel firmware support, including the firmware install command.

So, the firmware package does not make sense any more.  Remove it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Riku Voipio <riku.voipio@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 5620a0d1 ("firmware: delete in-kernel firmware") deleted
in-kernel firmware support, including "make firmware_install".

Since then, "make rpm-pkg" / "make binrpm-pkg" fails to build with
the error:

  make[2]: *** No rule to make target `firmware_install'.  Stop.

Commit df85b2d7 ("firmware: Restore support for built-in firmware")
restored the build infrastructure for CONFIG_EXTRA_FIRMWARE, but this
is out of the scope of "make firmware_install".  So, the right thing to
do is to kill the use of "make firmware_install".

Fixes: 5620a0d1 ("firmware: delete in-kernel firmware")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a new sysctl file /proc/sys/s390/topology which displays if
topology is on (1) or off (0) as specified by the "topology=" kernel
parameter.

This allows to change topology information during runtime and
configuring it via /etc/sysctl.conf instead of using the kernel line
parameter.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

If running on machines that do not provide topology information we
currently generate a "fake" topology which defines the maximum
distance between each cpu: each cpu will be put into an own drawer.

Historically this used to be the best option for (virtual) machines in
overcommited hypervisors.

For some workloads however it is better to generate a different
topology where all cpus are siblings within a package (all cpus are
core siblings). This shows performance improvements of up to 10%,
depending on the workload.

In order to keep the current behaviour, but also allow to switch to
the different core sibling topology use the existing "topology="
kernel parameter:

Specifying "topology=on" on machines without topology information will
generate the core siblings (fake) topology information, instead of the
default topology information where all cpus have the maximum distance.

On machines which provide topology information specifying
"topology=on" does not have any effect.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Optprobes depended on an updated regs->nip from analyse_instr() to
identify the location to branch back from the optprobes trampoline.
However, since commit 3cdfcbfd ("powerpc: Change analyse_instr so
it doesn't modify *regs"), analyse_instr() doesn't update the registers
anymore.  Due to this, we end up branching back from the optprobes
trampoline to the same branch into the trampoline resulting in a loop.

Fix this by calling out to emulate_update_regs() before using the nip.
Additionally, explicitly compare the return value from analyse_instr()
to 1, rather than just checking for !0 so as to guard against any
future changes to analyse_instr() that may result in -1 being returned
in more scenarios.

Fixes: 3cdfcbfd ("powerpc: Change analyse_instr so it doesn't modify *regs")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Merge one commit from Scott which I missed while away.

When two adjacent TX SGL are processed and parts of both TX SGLs
are pulled into the per-request TX SGL, the wrong per-request
TX SGL entries were updated.

This fixes a NULL pointer dereference when a cipher implementation walks
the TX SGL where some of the SGL entries were NULL.

Fixes: e870456d ("crypto: algif_skcipher - overhaul memory...")
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When built using multi_v7_defconfig, driver does not work on LS1021A:
[...]
caam 1700000.crypto: can't identify CAAM ipg clk: -2
caam: probe of 1700000.crypto failed with error -2
[...]

It turns out we have to detect at runtime whether driver is running
on an i.MX platform or not.

Cc: <stable@vger.kernel.org>
Fixes: 6c3af955 ("crypto: caam - add support for LS1021A")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

All older compiler versions up to gcc-4.9 produce these
harmless warnings:

drivers/crypto/inside-secure/safexcel_cipher.c:389:9: warning: missing braces around initializer [-Wmissing-braces]
drivers/crypto/inside-secure/safexcel_cipher.c:389:9: warning: (near initialization for ‘result.completion’) [-Wmissing-braces]
drivers/crypto/inside-secure/safexcel_hash.c:422:9: warning: missing braces around initializer [-Wmissing-braces]
drivers/crypto/inside-secure/safexcel_hash.c:422:9: warning: (near initialization for ‘result.completion’) [-Wmissing-braces]

This changes the syntax to something that works on all versions
without warnings.

Fixes: 1b44c5a6 ("crypto: inside-secure - add SafeXcel EIP197 crypto engine driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Today, md5sum fails with error -ENOKEY because a setkey
function is set for non hmac hashing algs, see strace output below:

mmap(NULL, 378880, PROT_READ, MAP_SHARED, 6, 0) = 0x77f50000
accept(3, 0, NULL)                      = 7
vmsplice(5, [{"bin/\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 378880}], 1, SPLICE_F_MORE|SPLICE_F_GIFT) = 262144
splice(4, NULL, 7, NULL, 262144, SPLICE_F_MORE) = -1 ENOKEY (Required key not available)
write(2, "Generation of hash for file kcap"..., 50) = 50
munmap(0x77f50000, 378880)              = 0

This patch ensures that setkey() function is set only
for hmac hashing.

Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

md5sum on some files gives wrong result

Exemple:

With the md5sum from libkcapi:
c15115c05bad51113f81bdaee735dd09  test

With the original md5sum:
bbdf41d80ba7e8b2b7be3a0772be76cb  test

This patch fixes this issue

Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Kernel crypto tests report the following error at startup

[    2.752626] alg: hash: Test 4 failed for sha224-talitos
[    2.757907] 00000000: 30 e2 86 e2 e7 8a dd 0d d7 eb 9f d5 83 fe f1 b0
00000010: 2d 5a 6c a5 f9 55 ea fd 0e 72 05 22

This patch fixes it

Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Using RBP as a temporary register breaks frame pointer convention and
breaks stack traces when unwinding from an interrupt in the crypto code.

Use R13 instead of RBP.  Both are callee-saved registers, so the
substitution is straightforward.
Reported-by: Eric Biggers <ebiggers@google.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Eric Biggers <ebiggers@google.com>
Acked-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Using RBP as a temporary register breaks frame pointer convention and
breaks stack traces when unwinding from an interrupt in the crypto code.

Mix things up a little bit to get rid of the RBP usage, without hurting
performance too much.  Use RDI instead of RBP for the TBL pointer.  That
will clobber CTX, so spill CTX onto the stack and use R12 to read it in
the outer loop.  R12 is used as a non-persistent temporary variable
elsewhere, so it's safe to use.

Also remove the unused y4 variable.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Eric Biggers <ebiggers@google.com>
Acked-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>