Move static codes to setup from init_hook for each model.

Also, use the common auto-mic selection helper for devices that support
auto-mic selection.  They just need to set up ext_mic, int_mic and
auto_mic flag in the setup section.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added setup hook to ALC preset struct to be called at in the parser
but not at each init callback.
This can be used for setting up the static pins, etc, while the
init hook should be used for updating the status again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Created a white-list to enable MSI since some devices require MSI
explicitly due to BIOS/ACPI problems.  Simply using a quirk list.
As the first case, take HP Compaq CQ40.

Reference: Novell bnc#529971
	https://bugzilla.novell.com/show_bug.cgi?id=529971Signed-off-by: Takashi Iwai <tiwai@suse.de>

Some Realtek codecs don't provide the full connections for certain pins
from each ADC; e.g. ACL662/ALC272 gives only one of two digital-mic pins
for each ADC.  Thus, depending on the digital mic pin, the ADC/MUX to be
used has to be chosen properly.

This patch adds the check of the connectivity of pins at auto-mic mode.
If no proper connectivity is found, auto_mic flag is turned off to be
sure.

Also the mux_idx is determined during this check so it won't be checked
in the unsol event any more.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALC269 and ALC861-VD parsers override the ADC definitions
unconditionally without checking the spec definition.  This causes
the problem when any inconsistent ADC is set up in the device quirk
(like ALC272 with digital-mic).

This patch avoids the overriding by adding the proper checks.

Reference: Novell bnc#529467
	https://bugzilla.novell.com/show_bug.cgi?id=529467Signed-off-by: Takashi Iwai <tiwai@suse.de>

When the auto-mic feature is enabled, we should support only one
capture stream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added the support for automatic mic selection via plugging for
Realtek codecs (in auto-probing mode).  The auto-mic mode is enabled
only when one internal mic and one external mic are present.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Without the initialization of vmaster NID, the dB information got
confused for ALC269 codec.

Reference: Novell bnc#527361
	https://bugzilla.novell.com/show_bug.cgi?id=527361Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

The previous auto-mic patch for STAC/IDT codecs causes the Oops on
machines without digital mic pins.  This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The new HP laptops have PCI SSID 103c:701x and requires model=hp-dv5.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When the line-out jack is plugged/unplugged, the driver needs to check
the headphone plug, not only the line-out jack itself.  Otherwise the
headphone or the speaker may be wrongly muted/unmuted.

As a result, both STAC_HP_EVENT and STAC_LO_EVENT need to call the
same function, stac92xx_hp_detect().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The commit fefd67f3
    ALSA: hda - Add line-out jack detection on IDT/STAC codecs
enabled wrong pins for jack detections.  Fixed to the correct ones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The new IbexPeak HDMI codec has 3 pin nodes and 2 converter nodes.
Here we assume only the first ones will be used.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The commit 24918b61 statically changes
the model from dell-bios to dell-3stack to solve the sound decreasing
regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another
problem that the 2nd headphone jack doesn't work
(https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think
the commit 249**2dc is just a workaround. I would like to give a true solution
here.

The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and
the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as
GPIO2. This patch changes EAPD to GPIO0 to solve the problem.
Signed-off-by: Chengu Wang <wangchengu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

To help disclose hardware bugs.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This converts the last CORBWP access outside of reg_lock.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just for safety.  azx_init_cmd_io() and azx_free_cmd_io() may be
called when switching to single command mode.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now that each codec will have its own module, it is possible
for the user to load one codec while another one is running.

So cmd_mutex would be a safe addition to probe_codec().
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Recently we hit a bug in our dev board, whose HDMI codec#3 may emit
redundant/spurious responses, which were then taken as responses to
command for another onboard Realtek codec#2, and mess up both codecs.

Extend the azx_rb.cmds and azx_rb.res to array and track each codec's
commands/responses separately. This helps keep good codec safe from
broken ones.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Use model=lenovo instead of model=dallas for Toshiba Satellite A135-S4527
with ALC861-VD codec.

Reference: Novell bnc#526325
	https://bugzilla.novell.com/show_bug.cgi?id=526325Signed-off-by: Takashi Iwai <tiwai@suse.de>

The name buf with size 16 is too short for some codec names, e.g.
truncated like "ALC861-VD Analo".  Now the size is doubled.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add the automatic mute of speakers via line-out jack plugging on
STAC/IDT codecs.  The feature is enabled when the HP detect is present.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The patch below, to be applied on the latest sound-unstable-2.6.git,
enables headphones output on my MacBookPro 5,5, together with the
automuting feature.

Here is the exact soundcard id:
	Vendor Id: 0x10134206
	Subsystem Id: 0x106b4d00
	Revision Id: 0x100301
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The commit 6479c631
    ALSA: hda - Create Capture controls dynamically
introduced typos of "Capture".  Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It auto mutes all 8-channel outputs at rear panel when
the front panel headphone is connected.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This 2-channel mode is useful in that it will broadcast
a 2-channel audio stream to all front/side/... ports.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The analog mix is disabled now as default (unless "analog_mixer" hint
is given), so it shoudn't appear in the digital input source as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added the missing initialization of DMUX connection (to analog input)
for auto-mic mode with STAC/IDT codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We don't need any more static connection to the port F (which is often
used for docking stations) since its connection is done dynamically via
DAC assignment now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

e->sad[] is declared with size ELD_MAX_SAD=16, but the guard
allows range 0-31.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Support the automatic mic-switching with some devices with IDT/STAC
codecs.  The condition is that the device has only two inputs, one
for an external mic and one for an internal mic.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since only one event can be associated to a (pin) widget, it's safer
to avoid the multiple mapping.  This patch fixes the behavior of the
STAC/IDT codec driver.

Now stac_get_event() doesn't take the type argument but simply returns
the first hit element.  Then enable_pin_detect() checks the validity
of the type, and returns non-zero only if a valid entry.  The caller
can call stac_issue_unsol_event() after checking the return value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The analog mixer unit on IDT 92HD71Bxx codecs is almost useless
since we use only the direct connections from DAC to pin.

Remove the controls to avoid unneeded confusion as default now.
This can be still back via "analog_mixer = 1" hint.
Signed-off-by: Takashi Iwai <tiwai@suse.de>