When xfs_growfs_data_private() is updating backup superblocks,
it bails out on the first error encountered, whether reading or
writing:

* If we get an error writing out the alternate superblocks,
* just issue a warning and continue.  The real work is
* already done and committed.

This can cause a problem later during repair, because repair
looks at all superblocks, and picks the most prevalent one
as correct.  If we bail out early in the backup superblock
loop, we can end up with more "bad" matching superblocks than
good, and a post-growfs repair may revert the filesystem to
the old geometry.

With the combination of superblock verifiers and old bugs,
we're more likely to encounter read errors due to verification.

And perhaps even worse, we don't even properly write any of the
newly-added superblocks in the new AGs.

Even with this change, growfs will still say:

  xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Structure needs cleaning
  data blocks changed from 319815680 to 335216640

which might be confusing to the user, but it at least communicates
that something has gone wrong, and dmesg will probably highlight
the need for an xfs_repair.

And this is still best-effort; if verifiers fail on more than
half the backup supers, they may still "win" - but that's probably
best left to repair to more gracefully handle by doing its own
strict verification as part of the backup super "voting."
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com> 
Signed-off-by: Ben Myers <bpm@sgi.com>

If we get EWRONGFS due to probing of non-xfs filesystems,
there's no need to issue the scary corruption error and backtrace.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>

__xfs_printk adds its own "\n".  Having it in the original string
leads to unintentional blank lines from these messages.

Most format strings have no newline, but a few do, leading to
i.e.:

[ 7347.119911] XFS (sdb2): Access to block zero in inode 132 start_block: 0 start_off: 0 blkcnt: 0 extent-state: 0 lastx: 1a05
[ 7347.119911] 
[ 7347.119919] XFS (sdb2): Access to block zero in inode 132 start_block: 0 start_off: 0 blkcnt: 0 extent-state: 0 lastx: 1a05
[ 7347.119919] 

Fix them all.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Recent analysis of a deadlocked XFS filesystem from a kernel
crash dump indicated that the filesystem was stuck waiting for log
space. The short story of the hang on the RHEL6 kernel is this:

	- the tail of the log is pinned by an inode
	- the inode has been pushed by the xfsaild
	- the inode has been flushed to it's backing buffer and is
	  currently flush locked and hence waiting for backing
	  buffer IO to complete and remove it from the AIL
	- the backing buffer is marked for write - it is on the
	  delayed write queue
	- the inode buffer has been modified directly and logged
	  recently due to unlinked inode list modification
	- the backing buffer is pinned in memory as it is in the
	  active CIL context.
	- the xfsbufd won't start buffer writeback because it is
	  pinned
	- xfssyncd won't force the log because it sees the log as
	  needing to be covered and hence wants to issue a dummy
	  transaction to move the log covering state machine along.

Hence there is no trigger to force the CIL to the log and hence
unpin the inode buffer and therefore complete the inode IO, remove
it from the AIL and hence move the tail of the log along, allowing
transactions to start again.

Mainline kernels also have the same deadlock, though the signature
is slightly different - the inode buffer never reaches the delayed
write lists because xfs_buf_item_push() sees that it is pinned and
hence never adds it to the delayed write list that the xfsaild
flushes.

There are two possible solutions here. The first is to simply force
the log before trying to cover the log and so ensure that the CIL is
emptied before we try to reserve space for the dummy transaction in
the xfs_log_worker(). While this might work most of the time, it is
still racy and is no guarantee that we don't get stuck in
xfs_trans_reserve waiting for log space to come free. Hence it's not
the best way to solve the problem.

The second solution is to modify xfs_log_need_covered() to be aware
of the CIL. We only should be attempting to cover the log if there
is no current activity in the log - covering the log is the process
of ensuring that the head and tail in the log on disk are identical
(i.e. the log is clean and at idle). Hence, by definition, if there
are items in the CIL then the log is not at idle and so we don't
need to attempt to cover it.

When we don't need to cover the log because it is active or idle, we
issue a log force from xfs_log_worker() - if the log is idle, then
this does nothing.  However, if the log is active due to there being
items in the CIL, it will force the items in the CIL to the log and
unpin them.

In the case of the above deadlock scenario, instead of
xfs_log_worker() getting stuck in xfs_trans_reserve() attempting to
cover the log, it will instead force the log, thereby unpinning the
inode buffer, allowing IO to be issued and complete and hence
removing the inode that was pinning the tail of the log from the
AIL. At that point, everything will start moving along again. i.e.
the xfs_log_worker turns back into a watchdog that can alleviate
deadlocks based around pinned items that prevent the tail of the log
from being moved...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

The xfs_inactive() return value is meaningless. Turn xfs_inactive()
into a void function and clean up the error handling appropriately.
Kill the VN_INACTIVE_[NO]CACHE directives as they are not relevant
to Linux.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Push the inode free work performed during xfs_inactive() down into
a new xfs_inactive_ifree() helper. This clears xfs_inactive() from
all inode locking and transaction management more directly
associated with freeing the inode xattrs, extents and the inode
itself.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Create the new xfs_inactive_truncate() function to handle the
truncate portion of xfs_inactive(). Push the locking and
transaction management into the new function.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Push down the transaction management for remote symlinks from
xfs_inactive() down to xfs_inactive_symlink_rmt(). The latter is
cleaned up to avoid transaction management intended for the
calling context (i.e., trans duplication, reservation, item
attachment).
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Add the inode type directory type support to XFS_IOC_FSGEOM
so that xfs_repair/xfs_info knows if the superblock v4 filesystem
enabled the feature.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

XFS never calls mark_inode_bad or iget_failed, so it will never see a
bad inode.  Remove all checks for is_bad_inode because they are
unnecessary.
Signed-off-by: Ben Myers <bpm@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>

At xfs_iext_realloc_direct(), the new_size is changed by adding
if_bytes if originally the extent records are stored at the inline
extent buffer, and we have to switch from it to a direct extent
list for those new allocated extents, this is wrong. e.g,

Create a file with three extents which was showing as following,

xfs_io -f -c "truncate 100m" /xfs/testme

for i in $(seq 0 5 10); do
	offset=$(($i * $((1 << 20))))
	xfs_io -c "pwrite $offset 1m" /xfs/testme
done

Inline
------
irec:	if_bytes	bytes_diff	new_size
1st	0		16		16
2nd	16		16		32

Switching
---------						rnew_size
3rd	32		16		48 + 32 = 80	roundup=128

In this case, the desired value of new_size should be 48, and then
it will be roundup to 64 and be assigned to rnew_size.

However, this issue has been covered by resetting the if_bytes to
the new_size which is calculated at the begnning of xfs_iext_add()
before leaving out this function, and in turn make the rnew_size
correctly again. Hence, this can not be detected via xfstestes.

This patch fix above problem and revise the new_size comments at
xfs_iext_realloc_direct() to make it more readable.  Also, fix the
comments while switching from the inline extent buffer to a direct
extent list to reflect this change.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Get rid of function variable count from xfs_iomap_write_allocate() as
it is unused.

Additionally, checkpatch warn me of the following for this change:
WARNING: extern prototypes should be avoided in .h files
+extern int xfs_iomap_write_allocate(struct xfs_inode *, xfs_off_t,

So this patch also remove all extern function prototypes at xfs_iomap.h
to suppress it to make this code style in consistent manner in this file.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

This fixes a build failure caused by calling the free() function which
does not exist in the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Free the memory in error path of xlog_recover_add_to_trans().
Normally this memory is freed in recovery pass2, but is leaked
in the error path.
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

The determination of whether a directory entry contains a dtype
field originally was dependent on the filesystem having CRCs
enabled. This meant that the format for dtype beign enabled could be
determined by checking the directory block magic number rather than
doing a feature bit check. This was useful in that it meant that we
didn't need to pass a struct xfs_mount around to functions that
were already supplied with a directory block header.

Unfortunately, the introduction of dtype fields into the v4
structure via a feature bit meant this "use the directory block
magic number" method of discriminating the dirent entry sizes is
broken. Hence we need to convert the places that use magic number
checks to use feature bit checks so that they work correctly and not
by chance.

The current code works on v4 filesystems only because the dirent
size roundup covers the extra byte needed by the dtype field in the
places where this problem occurs.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Michael Semon reported that xfs/299 generated this lockdep warning:

=============================================
[ INFO: possible recursive locking detected ]
3.12.0-rc2+ #2 Not tainted
---------------------------------------------
touch/21072 is trying to acquire lock:
 (&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64

but task is already holding lock:
 (&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&xfs_dquot_other_class);
  lock(&xfs_dquot_other_class);

 *** DEADLOCK ***

 May be due to missing lock nesting notation

7 locks held by touch/21072:
 #0:  (sb_writers#10){++++.+}, at: [<c11185b6>] mnt_want_write+0x1e/0x3e
 #1:  (&type->i_mutex_dir_key#4){+.+.+.}, at: [<c11078ee>] do_last+0x245/0xe40
 #2:  (sb_internal#2){++++.+}, at: [<c122c9e0>] xfs_trans_alloc+0x1f/0x35
 #3:  (&(&ip->i_lock)->mr_lock/1){+.+...}, at: [<c126cd1b>] xfs_ilock+0x100/0x1f1
 #4:  (&(&ip->i_lock)->mr_lock){++++-.}, at: [<c126cf52>] xfs_ilock_nowait+0x105/0x22f
 #5:  (&dqp->q_qlock){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64
 #6:  (&xfs_dquot_other_class){+.+...}, at: [<c12902fb>] xfs_trans_dqlockedjoin+0x57/0x64

The lockdep annotation for dquot lock nesting only understands
locking for user and "other" dquots, not user, group and quota
dquots. Fix the annotations to match the locking heirarchy we now
have.
Reported-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Commit f5ea1100 cleans up the disk to host conversions for
node directory entries, but because a variable is reused in
xfs_node_toosmall() the next node is not correctly found.
If the original node is small enough (<= 3/8 of the node size),
this change may incorrectly cause a node collapse when it should
not. That will cause an assert in xfstest generic/319:

   Assertion failed: first <= last && last < BBTOB(bp->b_length),
   file: /root/newest/xfs/fs/xfs/xfs_trans_buf.c, line: 569

Keep the original node header to get the correct forward node.

(When a node is considered for a merge with a sibling, it overwrites the
 sibling pointers of the original incore nodehdr with the sibling's
 pointers.  This leads to loop considering the original node as a merge
 candidate with itself in the second pass, and so it incorrectly
 determines a merge should occur.)
Signed-off-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

[v3: added Dave Chinner's (slightly modified) suggestion to the commit header,
	cleaned up whitespace.  -bpm]

After a fair number of xfstests runs, xfs/182 started to fail
regularly with a corrupted directory - a directory read verifier was
failing after recovery because it found a block with a XARM magic
number (remote attribute block) rather than a directory data block.

The first time I saw this repeated failure I did /something/ and the
problem went away, so I was never able to find the underlying
problem. Test xfs/182 failed again today, and I found the root
cause before I did /something else/ that made it go away.

Tracing indicated that the block in question was being correctly
logged, the log was being flushed by sync, but the buffer was not
being written back before the shutdown occurred. Tracing also
indicated that log recovery was also reading the block, but then
never writing it before log recovery invalidated the cache,
indicating that it was not modified by log recovery.

More detailed analysis of the corpse indicated that the filesystem
had a uuid of "a4131074-1872-4cac-9323-2229adbcb886" but the XARM
block had a uuid of "8f32f043-c3c9-e7f8-f947-4e7f989c05d3", which
indicated it was a block from an older filesystem. The reason that
log recovery didn't replay it was that the LSN in the XARM block was
larger than the LSN of the transaction being replayed, and so the
block was not overwritten by log recovery.

Hence, log recovery cant blindly trust the magic number and LSN in
the block - it must verify that it belongs to the filesystem being
recovered before using the LSN. i.e. if the UUIDs don't match, we
need to unconditionally recovery the change held in the log.

This patch was first tested on a block device that was repeatedly
causing xfs/182 to fail with the same failure on the same block with
the same directory read corruption signature (i.e. XARM block). It
did not fail, and hasn't failed since.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

It uses a kernel internal structure in it's definition rather than
the user visible structure that is passed to the ioctl.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

When we free an inode, we do so via RCU. As an RCU lookup can occur
at any time before we free an inode, and that lookup takes the inode
flags lock, we cannot safely assert that the flags lock is not held
just before marking it dead and running call_rcu() to free the
inode.

We check on allocation of a new inode structre that the lock is not
held, so we still have protection against locks being leaked and
hence not correctly initialised when allocated out of the slab.
Hence just remove the assert...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Regression introduced by commit 46f9d2eb ("xfs: aborted buf items can
be in the AIL") which fails to lock the AIL before removing the
item. Spinlock debugging throws a warning about this.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>

Pull timer code update from Thomas Gleixner:
 - armada SoC clocksource overhaul with a trivial merge conflict
 - Minor improvements to various SoC clocksource drivers

* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
  clocksource: armada-370-xp: Get reference fixed-clock by name
  clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
  clocksource: armada-370-xp: Fix device-tree binding
  clocksource: armada-370-xp: Introduce new compatibles
  clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
  clocksource: armada-370-xp: Simplify TIMER_CTRL register access
  clocksource: armada-370-xp: Use BIT()
  ARM: timer-sp: Set dynamic irq affinity
  ARM: nomadik: add dynamic irq flag to the timer
  clocksource: sh_cmt: 32-bit control register support
  clocksource: em_sti: Convert to devm_* managed helpers

Pull CIFS fixes from Steve French:
 "Two minor cifs fixes and a minor documentation cleanup for cifs.txt"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update cifs.txt and remove some outdated infos
  cifs: Avoid calling unlock_page() twice in cifs_readpage() when using fscache
  cifs: Do not take a reference to the page in cifs_readpage_worker()

Pull UBI fixes from Artem Bityutskiy:
 "Just a single fastmap fix plus a regression fix"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubi:
  UBI: Fix invalidate_fastmap()
  UBI: Fix PEB leak in wear_leveling_worker()

Pull ubifs fix from Artem Bityutskiy:
 "Just one patch which fixes the power-cut recovery testing mode.

  I'll start using a single UBI/UBIFS tree instead of 2 trees from now
  on.  So in the future you'll get 1 small pull request instead of 2
  tiny ones"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubifs:
  UBIFS: remove invalid warn msg with tst_recovery enabled

Pull MIPS fixes from Ralf Baechle:
 "These are four patches for three construction sites:

   - Fix register decoding for the combination of multi-core processors
     and multi-threading.

   - Two more fixes that are part of the ongoing DECstation resurrection
     work.  One of these touches a DECstation-only network driver.

   - Finally Markos' trivial build fix for the AP/SP support.

  (With this applied now all MIPS defconfigs are building again)"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
  MIPS: Fix SMP core calculations when using MT support.
  MIPS: DECstation I/O ASIC DMA interrupt handling fix
  MIPS: DECstation HRT initialization rearrangement

Pull x86 platform updates from Matthew Garrett:
 "Nothing amazing here, almost entirely cleanups and minor bugfixes and
  one bit of hardware enablement in the amilo-rfkill driver"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  platform/x86: panasonic-laptop: reuse module_acpi_driver
  samsung-laptop: fix config build error
  platform: x86: remove unnecessary platform_set_drvdata()
  amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
  wmi: parse_wdg() should return kernel error codes
  hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
  platform: replace strict_strto*() with kstrto*()
  x86: irst: use module_acpi_driver to simplify the code
  x86: smartconnect: use module_acpi_driver to simplify the code
  platform samsung-q10: use ACPI instead of direct EC calls
  thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
  thinkpad_acpi: return -NODEV while operating uninitialized LEDs

Pull misc SCSI driver updates from James Bottomley:
 "This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
  ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
  ibmvfc error handling) and the first round of esas2r checker fixes and
  finally the much anticipated big endian additions for megaraid_sas"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
  [SCSI] fnic: fnic Driver Tuneables Exposed through CLI
  [SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
  [SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
  [SCSI] fnic: Remove QUEUE_FULL handling code
  [SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
  [SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
  [SCSI] sd: Fix potential out-of-bounds access
  [SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
  [SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
  [SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
  [SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
  [SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
  [SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
  [SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
  [SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
  [SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
  [SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
  [SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
  [SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
  [SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
  ...

Pull SLAB update from Pekka Enberg:
 "Nothing terribly exciting here apart from Christoph's kmalloc
  unification patches that brings sl[aou]b implementations closer to
  each other"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slab: Use correct GFP_DMA constant
  slub: remove verify_mem_not_deleted()
  mm/sl[aou]b: Move kmallocXXX functions to common code
  mm, slab_common: add 'unlikely' to size check of kmalloc_slab()
  mm/slub.c: beautify code for removing redundancy 'break' statement.
  slub: Remove unnecessary page NULL check
  slub: don't use cpu partial pages on UP
  mm/slub: beautify code for 80 column limitation and tab alignment
  mm/slub: remove 'per_cpu' which is useless variable

Pull input update from Dmitry Torokhov:
 "The only change is David Hermann's new EVIOCREVOKE evdev ioctl that
  allows safely passing file descriptors to input devices to session
  processes and later being able to stop delivery of events through
  these fds so that inactive sessions will no longer receive user input
  that does not belong to them"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: evdev - add EVIOCREVOKE ioctl

Sedat points out that I transposed some letters in "LRU" and wrote "RLU"
instead in one of the new comments explaining the flow.  Let's just fix
it.
Reported-by: Sedat Dilek <sedat.dilek@jpberlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Matt found that commit 27a7c642 ("partitions/efi: account for pmbr
size in lba") caused his GPT formatted eMMC device not to boot.  The
reason is that this commit enforced Linux to always check the lesser of
the whole disk or 2Tib for the pMBR size in LBA.  While most disk
partitioning tools out there create a pMBR with these characteristics,
Microsoft does not, as it always sets the entry to the maximum 32-bit
limitation - even though a drive may be smaller than that[1].

Loosen this check and only verify that the size is either the whole disk
or 0xFFFFFFFF.  No tool in its right mind would set it to any value
other than these.

[1] http://thestarman.pcministry.com/asm/mbr/GPT.htm#GPTPTReported-and-tested-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull writeback fix from Wu Fengguang:
 "A trivial writeback fix"

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: Do not sort b_io list only because of block device inode

The LRU list changes interacted badly with our nr_dentry_unused
accounting, and even worse with the new DCACHE_LRU_LIST bit logic.

This introduces helper functions to make sure everything follows the
proper dcache d_lru list rules: the dentry cache is complicated by the
fact that some of the hotpaths don't even want to look at the LRU list
at all, and the fact that we use the same list entry in the dentry for
both the LRU list and for our temporary shrinking lists when removing
things from the LRU.

The helper functions temporarily have some extra sanity checking for the
flag bits that have to match the current LRU state of the dentry.  We'll
remove that before the final 3.12 release, but considering how easy it
is to get wrong, this first cleanup version has some very particular
sanity checking.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Björn JACKE <bj@sernet.de>
Signed-off-by: Steve French <smfrench@gmail.com>

When reading a single page with cifs_readpage(), we make a call to
fscache_read_or_alloc_page() which once done, asynchronously calls
the completion function cifs_readpage_from_fscache_complete(). This
completion function unlocks the page once it has been populated from
cache. The module then attempts to unlock the page a second time in
cifs_readpage() which leads to warning messages.

In case of a successful call to fscache_read_or_alloc_page() we should skip
the second unlock_page() since this will be called by the
cifs_readpage_from_fscache_complete() once the page has been populated by
fscache.

With the modifications to cifs_readpage_worker(), we will need to re-grab the
page lock in cifs_write_begin().

The problem was first noticed when testing new fscache patches for cifs.
https://bugzilla.redhat.com/show_bug.cgi?id=1005737Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>

We do not need to take a reference to the pagecache in
cifs_readpage_worker() since the calling function will have already
taken one before passing the pointer to the page as an argument to the
function.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>

Pull hwmon fixes from Guenter Roeck:
 "Some more low risk cleanup patches:

   - Remove unnecessary pci_set_drvdata in k10temp driver from Jingoo Han
   - Fix return values in several drivers from Sachin Kamat
   - Remove redundant break in amc6821 driver from Sachin Kamat"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (k10temp) remove unnecessary pci_set_drvdata()
  hwmon: (tmp421) Fix return value
  hwmon: (amc6821) Remove redundant break
  hwmon: (amc6821) Fix return value
  hwmon: (ibmaem) Fix return value
  hwmon: (emc2103) Fix return value

Pull Xtensa updates from Chris Zankel.

* tag 'xtensa-next-20130912' of git://github.com/czankel/xtensa-linux:
  xtensa: Fix broken allmodconfig build
  xtensa: remove CCOUNT_PER_JIFFY
  xtensa: fix !CONFIG_XTENSA_CALIBRATE_CCOUNT build failure
  xtensa: don't use echo -e needlessly
  xtensa: new fast_alloca handler
  xtensa: keep a3 and excsave1 on entry to exception handlers
  xtensa: enable kernel preemption
  xtensa: check thread flags atomically on return from user exception