Add soft reset support to cleanup_halted_endpoint().
using soft reset will prevent it from setting a new dequeue pointer to
start the transfer from. Let it continue where it halted.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci supports soft retry recovery when the host halted the host side of an
endopint but the connected USB device is not aware of the halt.

In this case xhci needs to issue a reset endopint command  with a TSP
(Transfer State Preserve) flag set which preserves the Data toggle
and Sequence number of the endpoint.

This feature is needed to handle a few special transfer event types
such as USB Transaction error that don't always point to a causing TRB.

see xhci 4.6.8.1 for more details
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Parse the transfer event first, and remove duplicate debugging
code.

Reorder completion codes according to endpoint state.

No functional changes

We are not handling some transfer events correcly and need to
clean up this before fixing it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Anurag Kumar Vulisha reported several issues with xhci endpoint
ring caching.

31 Rings are cached per device before a ring is freed.
These cached rings are not used as default if a new ring is needed.
They are only used if the driver fails to allocate memory for a ring.

The current ring cache is more a reason to why we run out memory than a
help when we actually do so.

Anurag Kumar Vulisha tried to use cached rings as a first option and
found new issues with cached ring initialization.
Cached rings were first zeroed and then manually reinitialized with link
trbs etc, but forgetting to set some important bits like cycle toggle bit.

Remove the ring cache completely as it's a faulty premature optimization
eating memory
Reported-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The original motivation for disabling/enabling Link PM at device
suspend/resume was to force link state to go via U0 before suspend sets
the link state to U3. Going directly from U2 to U3 is not allowed.

Disabling LPM will forced the link state to U0, but will send a lot of
Set port feature requests for evert suspend and resume.

This is not needed as Hub hardware will take care of going via U0
when a U2 -> U3 transition is requested [1]

[1] USB 3.1 specification section 10.16.2.10 Set Port Feature:

"If the value is 3, then host software wants to selectively suspend the
device connected to this port. The hub shall transition the link to U3
from any of the other U states using allowed link state transitions.
If the port is not already in the U0 state, then it shall transition the
port to the U0 state and then initiate the transition to U3.
While this state is active, the hub does not propagate downstream-directed
traffic to this port, but the hub will respond to resume signaling from the
port"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new helper for reusing a device-tree node of another device
instead of managing the node references explicitly.

This also makes sure that the new of_node_reuse flag is set if the
device is ever reprobed, something which specifically now avoids driver
core from attempting to claim any pinmux resources already claimed by
the parent device.

Fixes: ec4664b3 ("thermal: max77620: Add thermal driver for reporting junction temp")
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The thermal child device reuses the parent MFD-device device-tree node
when registering a thermal zone, but did not take a reference to the
node.

This leads to a reference imbalance, and potential use-after-free, when
the node reference is dropped by the platform-bus device destructor
(once for the child and later again for the parent).

Fix this by dropping any reference already held to a device-tree node
and getting a reference to the parent's node which will be balanced on
reprobe or on platform-device release, whichever comes first.

Note that simply clearing the of_node pointer on probe errors and on
driver unbind would not allow the use of device-managed resources as
specifically thermal_zone_of_sensor_unregister() claims that a valid
device-tree node pointer is needed during deregistration (even if it
currently does not seem to use it).

Fixes: ec4664b3 ("thermal: max77620: Add thermal driver for reporting junction temp")
Cc: stable <stable@vger.kernel.org>     # 4.9
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In an attempt to work around a pinmux over-allocation issue in driver
core, commit dc5878ab ("usb: core: move root hub's device node
assignment after it is added to bus") moved the device-tree node
assignment until after the root hub had been registered.

This not only makes the device-tree node unavailable to the usb driver
during probe, but also prevents the of_node from being linked to in
sysfs and causes a race with user-space for the (recently added) devspec
attribute.

Use the new device_set_of_node_from_dev() helper to reuse the node of
the sysdev device, something which now prevents driver core from trying
to reclaim any pinctrl pins during probe.

Fixes: dc5878ab ("usb: core: move root hub's device node assignment after it is added to bus")
Fixes: 51fa9147 ("usb/core: Added devspec sysfs entry for devices behind the usb hub")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit ab78029e ("drivers/pinctrl: grab default handles from device
core") added automatic pin-control management to driver core by looking
up and setting any default pinctrl state found in device tree while a
device is being probed.

This obviously runs into problems as soon as device-tree nodes are
reused for child devices which are later also probed as pins would
already have been claimed by the ancestor device.

For example if a USB host controller claims a pin, its root hub would
consequently fail to probe when its device-tree node is set to the node
of the controller:

    pinctrl-single 48002030.pinmux: pin PIN204 already requested by 48064800.ehci; cannot claim for usb1
    pinctrl-single 48002030.pinmux: pin-204 (usb1) status -22
    pinctrl-single 48002030.pinmux: could not request pin 204 (PIN204) from group usb_dbg_pins  on device pinctrl-single
    usb usb1: Error applying setting, reverse things back
    usb: probe of usb1 failed with error -22

Fix this by checking the new of_node_reused flag and skipping automatic
pinctrl configuration during probe if set.

Note that the flag is checked in driver core rather than in pinctrl
(e.g. in pinctrl_dt_to_map()) which would specifically have prevented
intentional use of a parent's pinctrl properties by a child device
(should such a need ever arise).

Fixes: ab78029e ("drivers/pinctrl: grab default handles from device core")
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a helper function to be used when reusing the device-tree node of
another device.

It is fairly common for drivers to reuse the device-tree node of a
parent (or other ancestor) device when creating class or bus devices
(e.g. gpio chips, i2c adapters, iio chips, spi masters, serdev, phys,
usb root hubs). But reusing a device-tree node may cause problems if the
new device is later probed as for example driver core would currently
attempt to reinitialise an already active associated pinmux
configuration.

Other potential issues include the platform-bus code unconditionally
dropping the device-tree node reference in its device destructor,
reinitialisation of other bus-managed resources such as clocks, and the
recently added DMA-setup in driver core.

Note that for most examples above this is currently not an issue as the
devices are never probed, but this is a problem for the USB bus which
has recently gained device-tree support. This was discovered and
worked-around in a rather ad-hoc fashion by commit dc5878ab ("usb:
core: move root hub's device node assignment after it is added to bus")
by not setting the of_node pointer until after the root-hub device has
been registered.

Instead we can allow devices to reuse a device-tree node by setting a
flag in their struct device that can be used by core, bus and driver
code to avoid resources from being over-allocated.

Note that the helper also grabs an extra reference to the device node,
which specifically balances the unconditional put in the platform-device
destructor.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Document that the child-node lookup helper takes a reference to the
device-tree node which needs to be dropped after use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to release any OF device-node reference taken when creating
the USB device.

Note that we currently do not hold a reference to the root hub
device-tree node (i.e. the parent controller node).

Fixes: 69bec725 ("USB: core: let USB device know device node")
Cc: stable <stable@vger.kernel.org>	# v4.6
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use sysfs_match_string() helper instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Trace_printk() was used to log debug messages in xhci-dbc.c where
printk() isn't feasible. As there should not be a single caller to
trace_printk() in normal kernels, replace them with empty functions.

Cc: Vlastimil Babka <vbabka.lkml@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Each vhci has 2*VHCI_HC_PORTS ports, in which VHCI_HC_PORTS
ports are HighSpeed (or below), and VHCI_HC_PORTS are SuperSpeed.
This new macro VHCI_PORTS reflects this configuration.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As USB3 has (slightly) different bit meanings in the port
status. Add a new status bit array for USB3.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With this patch, USB_SPEED_SUPER is a valid speed when attaching
a USB3 SuperSpeed device.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a USB3 HCD to an existing USB2 HCD and provides
the support of SuperSpeed, in case the device can only be enumerated
with SuperSpeed.

The bulk of the added code in usb3_bos_desc and hub_control to support
SuperSpeed is borrowed from the commit 1cd8fd28 ("usb: gadget:
dummy_hcd: add SuperSpeed support").

With this patch, each vhci will have VHCI_HC_PORTS HighSpeed ports
and VHCI_HC_PORTS SuperSpeed ports.
Suggested-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch enables the new vhci structure. Its lock protects
both the USB2 hub and the shared USB3 hub.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A vhci struct is added as the platform-specific data to the vhci
platform device, in order to get the vhci by its platform device.
This is done in vhci_hcd_init().
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Every VHCI is a platform device, so move the platform_device struct
into the VHCI struct.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to support SuperSpeed devices, a USB3 HCD is added to
share the USB2 HCD. As a result, a VHCI is composed of two
vhci_hcds associated with the two HCDs respectively. So we add
another level of abstraction, vhci, and thus this vhci structure.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These helper function names are renamed to have their full struct
names to avoid confusion:

 - hcd_to_vhci() -> hcd_to_vhci_hcd()
 - vhci_to_hcd() -> vhci_hcd_to_hcd()
 - vdev_to_vhci() -> vdev_to_vhci_hcd()
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current definition is wrong. This breaks my upcoming
Aspeed virtual hub driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In parse_status(), all nports number of idev's are initiated to
0 by memset(), it is simply wrong, because parse_status() reads
the status sys file one by one, therefore, it can only update the
according vhci_driver->idev's for it to parse.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The commit 0775a9cb ("usbip: vhci extension: modifications
to vhci driver") introduced multiple controllers, but the status
of the ports are only extracted from the first status file, fix it.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A new field ncontrollers is added to the vhci_driver structure.
And this field is stored by scanning the vhci_hcd* dirs in the
platform udev.
Suggested-and-reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If we get nonpositive number of ports, there is no sense to
continue, then fail gracefully.

In addition, the commit 0775a9cb ("usbip: vhci extension:
modifications to vhci driver") introduced configurable numbers of
controllers and ports, but we have a static port number maximum,
MAXNPORT. If exceeded, the idev array will be overflown. We fix
it by validating the nports to make sure the port number max is
not exceeded.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The usbip stack dynamically allocates the transfer_buffer and
setup_packet of each urb that got generated by the tcp to usb stub code.
As these pointers are always used only once we will set them to NULL
after use. This is done likewise to the free_urb code in vudc_dev.c.
This patch fixes double kfree situations where the usbip remote side
added the URB_FREE_BUFFER.

Cc: stable@vger.kernel.org
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The usbfs interface does not provide any way for the user to learn the
speed at which a device is connected.  The current API includes a
USBDEVFS_CONNECTINFO ioctl, but all it provides is the device's
address and a one-bit value indicating whether the connection is low
speed.  That may have sufficed in the era of USB-1.1, but it isn't
good enough today.

This patch introduces a new ioctl, USBDEVFS_GET_SPEED, which returns a
numeric value indicating the speed of the connection: unknown, low,
full, high, wireless, super, or super-plus.

Similar information (not exactly the same) is available through sysfs,
but it seems reasonable to provide the actual value in usbfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Reinhard Huck <reinhard.huck@thesycon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull key subsystem fixes from James Morris:
 "Here are a bunch of fixes for Linux keyrings, including:

   - Fix up the refcount handling now that key structs use the
     refcount_t type and the refcount_t ops don't allow a 0->1
     transition.

   - Fix a potential NULL deref after error in x509_cert_parse().

   - Don't put data for the crypto algorithms to use on the stack.

   - Fix the handling of a null payload being passed to add_key().

   - Fix incorrect cleanup an uninitialised key_preparsed_payload in
     key_update().

   - Explicit sanitisation of potentially secure data before freeing.

   - Fixes for the Diffie-Helman code"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (23 commits)
  KEYS: fix refcount_inc() on zero
  KEYS: Convert KEYCTL_DH_COMPUTE to use the crypto KPP API
  crypto : asymmetric_keys : verify_pefile:zero memory content before freeing
  KEYS: DH: add __user annotations to keyctl_kdf_params
  KEYS: DH: ensure the KDF counter is properly aligned
  KEYS: DH: don't feed uninitialized "otherinfo" into KDF
  KEYS: DH: forbid using digest_null as the KDF hash
  KEYS: sanitize key structs before freeing
  KEYS: trusted: sanitize all key material
  KEYS: encrypted: sanitize all key material
  KEYS: user_defined: sanitize key payloads
  KEYS: sanitize add_key() and keyctl() key payloads
  KEYS: fix freeing uninitialized memory in key_update()
  KEYS: fix dereferencing NULL payload with nonzero length
  KEYS: encrypted: use constant-time HMAC comparison
  KEYS: encrypted: fix race causing incorrect HMAC calculations
  KEYS: encrypted: fix buffer overread in valid_master_desc()
  KEYS: encrypted: avoid encrypting/decrypting stack buffers
  KEYS: put keyring if install_session_keyring_to_cred() fails
  KEYS: Delete an error message for a failed memory allocation in get_derived_key()
  ...

Commit abb2ea7d ("compiler, clang: suppress warning for unused
static inline functions") just caused more warnings due to re-defining
the 'inline' macro.

So undef it before re-defining it, and also add the 'notrace' attribute
like the gcc version that this is overriding does.

Maybe this makes clang happier.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull randomness fixes from Ted Ts'o:
 "Improve performance by using a lockless update mechanism suggested by
  Linus, and make sure we refresh per-CPU entropy returned get_random_*
  as soon as the CRNG is initialized"

* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: invalidate batched entropy after crng init
  random: use lockless method of accessing and updating f->reg_idx

Pull ext4 fixes from Ted Ts'o:
 "Fix various bug fixes in ext4 caused by races and memory allocation
  failures"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix fdatasync(2) after extent manipulation operations
  ext4: fix data corruption for mmap writes
  ext4: fix data corruption with EXT4_GET_BLOCKS_ZERO
  ext4: fix quota charging for shared xattr blocks
  ext4: remove redundant check for encrypted file on dio write path
  ext4: remove unused d_name argument from ext4_search_dir() et al.
  ext4: fix off-by-one error when writing back pages before dio read
  ext4: fix off-by-one on max nr_pages in ext4_find_unwritten_pgoff()
  ext4: keep existing extra fields when inode expands
  ext4: handle the rest of ext4_mb_load_buddy() ENOMEM errors
  ext4: fix off-by-in in loop termination in ext4_find_unwritten_pgoff()
  ext4: fix SEEK_HOLE
  jbd2: preserve original nofs flag during journal restart
  ext4: clear lockdep subtype for quota files on quota off

Pull GPIO fixes from Linus Walleij:
 "A few overdue GPIO patches for the v4.12 kernel.

   - Fix debounce logic on the Aspeed platform.

   - Fix the "virtual gpio" things on the Intel Crystal Cove.

   - Fix the blink counter selection on the MVEBU platform"

* tag 'gpio-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: mvebu: fix gpio bank registration when pwm is used
  gpio: mvebu: fix blink counter register selection
  MAINTAINERS: remove self from GPIO maintainers
  gpio: crystalcove: Do not write regular gpio registers for virtual GPIOs
  gpio: aspeed: Don't attempt to debounce if disabled

Pull char/misc driver fixes from Greg KH:
 "Here are some small driver fixes for 4.12-rc5. Nothing major here,
  just some small bugfixes found by people testing, and a MAINTAINERS
  file update for the genwqe driver.

  All have been in linux-next with no reported issues"

[ The cxl driver fix came in through the powerpc tree earlier ]

* tag 'char-misc-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  cxl: Avoid double free_irq() for psl,slice interrupts
  mei: make sysfs modalias format similar as uevent modalias
  drivers: char: mem: Fix wraparound check to allow mappings up to the end
  MAINTAINERS: Change maintainer of genwqe driver
  goldfish_pipe: use GFP_ATOMIC under spin lock
  firmware: vpd: do not leak kobjects
  firmware: vpd: avoid potential use-after-free when destroying section
  firmware: vpd: do not leave freed section attributes to the list