As documented in RFC4861 (Neighbor Discovery for IP version 6) 7.2.6.,
unsolicited neighbour advertisements should be sent to the all-nodes
multicast address.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

cdc_eem frames might need to contain 802.1Q VLAN Ethernet frames.
URB/skb sizing from usbnet will default to the hard_mtu,
so account for the VLAN header by expanding that via hard_header_len
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checking skb->len against ETH_FRAME_LEN assumes a 1514
ethernet frame size. With an 802.1Q VLAN header, ethernet
frame length can now be 1518. Validate frame length against that.
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

INGPADBOUNDARY_MASK is already shifted. No need to shift it again. On reloading
a driver it was resulting in a bad SGE FL MTU sizes [1536, 9088] error. This
only causes an issue on systems that have L1 cache size of 32B, 128B, 512B,
2048B or 4096B.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It doesn't make much sense to enable ISDN services if you don't
intend to connect to a network. Therefore insisting that ISDN
depends on NETDEVICES seems logical. We can then remove any
guards mentioning NETDEVICES inside all subordinate drivers.

This also has the nice side-effect of fixing the warning below
when ISDN_I4L && !CONFIG_NETDEVICES at compile time.

This patch fixes:
drivers/isdn/i4l/isdn_common.c: In function ‘isdn_ioctl’:
drivers/isdn/i4l/isdn_common.c:1278:8: warning: unused variable ‘s’ [-Wunused-variable]

Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not assume reserve fields to be don't cares as fields may change.
Clearing data structures before using.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a NULL dereference, the following patch is causing oops
in normal trafic condition:

commit c0de08d0
Author: Eric Leblond <eric@regit.org>
Date:   Thu Aug 16 22:02:58 2012 +0000

    af_packet: don't emit packet on orig fanout group

This buggy patch was a feature fix and has reached most stable
branches.

When skb->sk is NULL and when packet fanout is used, there is a
crash in match_fanout_group where skb->sk is accessed.
This patch fixes the issue by returning false as soon as the
socket is NULL: this correspond to the wanted behavior because
the kernel as to resend the skb to all the listening socket in
this case.
Signed-off-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the max packet size for some class (configured through tc) is
violated by the actual size of the packets of that class, then QFQ
would not schedule classes correctly, and the data structures
implementing the bucket lists may get corrupted. This problem occurs
with TSO/GSO even if the max packet size is set to the MTU, and is,
e.g., the cause of the failure reported in [1]. Two patches have been
proposed to solve this problem in [2], one of them is a preliminary
version of this patch.

This patch addresses the above issues by: 1) setting QFQ parameters to
proper values for supporting TSO/GSO (in particular, setting the
maximum possible packet size to 64KB), 2) automatically increasing the
max packet size for a class, lmax, when a packet with a larger size
than the current value of lmax arrives.

The drawback of the first point is that the maximum weight for a class
is now limited to 4096, which is equal to 1/16 of the maximum weight
sum.

Finally, this patch also forcibly caps the timestamps of a class if
they are too high to be stored in the bucket list. This capping, taken
from QFQ+ [3], handles the unfrequent case described in the comment to
the function slot_insert.

[1] http://marc.info/?l=linux-netdev&m=134968777902077&w=2
[2] http://marc.info/?l=linux-netdev&m=135096573507936&w=2
[3] http://marc.info/?l=linux-netdev&m=134902691421670&w=2Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Tested-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We've observed that in case if UDP diag module is not
supported in kernel the netlink returns NLMSG_DONE without
notifying a caller that handler is missed.

This patch makes __inet_diag_dump to return error code instead.

So as example it become possible to detect such situation
and handle it gracefully on userspace level.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: David Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct spelling typo in bnx2x driver
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

f7b29271 introduced tx checksum offload support for smsc95xx,
and enabled it by default. This feature doesn't take
endianness into account, so causes most tx to fail on
those platforms.

This patch fixes the problem fully by adding the missing
conversion.

An alternate workaround is to disable TX checksum offload
on those platforms. The cpu impact of this feature is very low.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the dflt fdb dump handler to use RTM_NEWNEIGH to
be compatible with bridge dump routines.

The dump reply from the network driver handlers should
match the reply from bridge handler. The fact they were
not in the ixgbe case was effectively a bug. This patch
resolves it.

Applications that were not checking the nlmsg type will
continue to work. And now applications that do check
the type will work as expected.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the adjfreq callback description to include a note that the
delta in ppb is always relative to the base frequency, and not to the current
frequency of the hardware clock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: stable@vger.kernel.org [v3.5+]
CC: Richard Cochran <richard.cochran@gmail.com>
CC: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RTL_GIGA_MAC_VER_35 includes no multicast hardware filter.
Signed-off-by: Nathan Walp <faceprint@faceprint.com>
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This regression was spotted between Debian squeeze and Debian wheezy
kernels (respectively based on 2.6.32 and 3.2). More info about
Wake-on-LAN issues with Realtek's 816x chipsets can be found in the
following thread: http://marc.info/?t=132079219400004

Probable regression from d4ed95d7;
more chipsets are likely affected.

Tested on top of a 3.2.23 kernel.
Reported-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Tested-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Hinted-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some driver uses tasklet_disable in device remove/close process,
tasklet_disable will inc tasklet->count and return. If the tasklet
is not handled yet because some softirq pressure, the tasklet will
placed on the tasklet_vec, never have a chance to excute. This might
lead to ksoftirqd heavy loaded, wakeup with pending_softirq, but
tasklet is disabled. tasklet_kill should be used in this case.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

If tasklet_disable() is called before related tasklet handled,
tasklet_kill will never be finished. tasklet_kill is enough.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "First post-Sandy pull request"

 1) Fix antenna gain handling and initialization of chan->max_reg_power
    in wireless, from Felix Fietkau.

 2) Fix nexthop handling in H.232 conntrack helper, from Julian
    Anastasov.

 3) Only process 80211 mesh config header in certain kinds of frames,
    from Javier Cardona.

 4) 80211 management frame header length needs to be validated, from
    Johannes Berg.

 5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.

 6) Test for permanent state correctly in VXLAN driver, from Stephen
    Hemminger.

 7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.

 8) Fix off by one errors in bonding, from Nikolay ALeksandrov.

 9) Fix divide by zero in TCP-Illinois congestion control.  From Jesper
    Dangaard Brouer.

10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
    sizeof of a sizeof, so you can size your size" Fix from Julian
    Anastasov.

11) Several drivers do mdiobus_free without first doing an
    mdiobus_unregister leading to stray pointer references.  Fix from
    Peter Senna Tschudin.

12) Fix OOPS in l2tp_eth_create() error path, it's another danling
    pointer kinda situation.  Fix from Tom Parkin.

13) Hardware driven by the vmxnet driver can't handle larger than 16K
    fragments, so split them up when necessary.  From Eric Dumazet.

14) Handle zero length data length in tcp_send_rcvq() properly.  Fix
    from Pavel Emelyanov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
  tcp-repair: Handle zero-length data put in rcv queue
  vmxnet3: must split too big fragments
  l2tp: fix oops in l2tp_eth_create() error path
  cxgb4: Fix unable to get UP event from the LLD
  drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
  drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
  bnx2x: fix HW initialization using fw 7.8.x
  tcp: Fix double sizeof in new tcp_metrics code
  net: fix divide by zero in tcp algorithm illinois
  net: sctp: Fix typo in net/sctp
  bonding: fix second off-by-one error
  bonding: fix off-by-one error
  bnx2x: Disable FCoE for 57840 since not yet supported by FW
  bnx2x: Fix no link on 577xx 10G-baseT
  bnx2x: Fix unrecognized SFP+ module after driver is loaded
  bnx2x: Fix potential incorrect link speed provision
  bnx2x: Restore global registers back to default.
  bnx2x: Fix link down in 57712 following LFA
  bnx2x: Fix 57810 1G-KR link against certain switches.
  ixgbe: PTP get_ts_info missing software support
  ...

When sending data into a tcp socket in repair state we should check
for the amount of data being 0 explicitly. Otherwise we'll have an skb
with seq == end_seq in rcv queue, but tcp doesn't expect this to happen
(in particular a warn_on in tcp_recvmsg shoots).
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Reported-by: Giorgos Mavrikas <gmavrikas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3 has a 16Kbytes limit per tx descriptor, that happened to work
as long as we provided PAGE_SIZE fragments.

Our stack can now build larger fragments, so we need to split them to
the 16kbytes boundary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: jongman heo <jongman.heo@samsung.com>
Tested-by: jongman heo <jongman.heo@samsung.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When creating an L2TPv3 Ethernet session, if register_netdev() should fail for
any reason (for example, automatic naming for "l2tpeth%d" interfaces hits the
32k-interface limit), the netdev is freed in the error path.  However, the
l2tp_eth_sess structure's dev pointer is left uncleared, and this results in
l2tp_eth_delete() then attempting to unregister the same netdev later in the
session teardown.  This results in an oops.

To avoid this, clear the session dev pointer in the error path.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on commit b27393ae

Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.

The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
  ... when != mdiobus_unregister(E);

+ mdiobus_unregister(E);
  mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on commit b27393ae

Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.

The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
  ... when != mdiobus_unregister(E);

+ mdiobus_unregister(E);
  mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull power management update from Rafael J. Wysocki:
 "Change the email address of the powernow-k8 maintainer."

* tag 'pm-for-3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq / powernow-k8: Change maintainer's email address

Pull input subsystem fixes from Dmitry Torokhov:
 "Just a few driver fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: tsc40 - remove wrong announcement of pressure support
  Input: lpc32xx-keys - select INPUT_MATRIXKMAP
  Input: pxa27x_keypad - clear pending interrupts on keypad config
  Input: wacom - correct bad Cintiq 24HD check
  Input: wacom - add INPUT_PROP_DIRECT flag to Cintiq 24HD
  Input: egalax_ts - get gpio from devicetree

Pull more scsi target fixes from Nicholas Bellinger:
 "This series is a second round of target fixes for v3.7-rc4 that have
  come into target-devel over the last days, and are important enough to
  be applied ASAP.

  All are being CC'ed to stable.  The most important two are:

   - target: Re-add explict zeroing of INQUIRY bounce buffer memory to
     fix a regression for handling zero-length payloads, a bug that went
     during v3.7-rc1, and hit >= v3.6.3 stable.  (nab + paolo)

   - iscsi-target: Fix a long-standing missed R2T wakeup race in TX
     thread processing when using a single queue slot.  (Roland)

  Thanks to Roland & PureStorage team for helping to track down this
  long standing race with iscsi-target single queue slot operation.

  Also, the tcm_fc(FCoE) regression bug that was observed recently with
  -rc2 code has also been resolved with the cancel_delayed_work() return
  bugfix (commit c0158ca6: "workqueue: cancel_delayed_work() should
  return %false if work item is idle") now in -rc3.  Thanks again to Yi
  Zou, MDR, Robert Love @ Intel for helping to track this down."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
  iscsi-target: Fix missed wakeup race in TX thread
  target: Avoid integer overflow in se_dev_align_max_sectors()
  target: Don't return success from module_init() if setup fails
  target: Re-add explict zeroing of INQUIRY bounce buffer memory

Pull hwmon fixes from Guenter Roeck:
 "An e-mail address update, and fix a compile error on SPARC"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: Only include of_match_table with CONFIG_OF_GPIO
  hwmon, fam15h_power: Change email address, MAINTAINERS entry

Pull FRV fixes from David Howells:
 "A collection of small fixes for the FRV architecture."

* tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv:
  frv: fix the broken preempt
  frv: switch to saner kernel_execve() semantics
  FRV: Fix the new-style kernel_thread() stuff
  FRV: Fix the preemption handling
  FRV: gcc-4.1.2 also inlines weak functions
  FRV: Don't objcopy the GNU build_id note
  FRV: Add missing linux/export.h #inclusions

Merge tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bugfixes from Konrad Rzeszutek Wilk:
 - Use appropriate macros instead of hand-rolling our own (ARM).
 - Fixes if FB/KBD closed unexpectedly.
 - Fix memory leak in /dev/gntdev ioctl calls.
 - Fix overflow check in xenbus_file_write.
 - Document cleanup.
 - Performance optimization when migrating guests.

* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/mmu: Use Xen specific TLB flush instead of the generic one.
  xen/arm: use the __HVC macro
  xen/xenbus: fix overflow check in xenbus_file_write()
  xen-kbdfront: handle backend CLOSED without CLOSING
  xen-fbfront: handle backend CLOSED without CLOSING
  xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
  x86: remove obsolete comment from asm/xen/hypervisor.h

This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
  patches that use this   - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Just get %icc2 into the state we would have after local_irq_disable()
and physical IRQ having happened since then.  Then we can simply
use preempt_schedule_irq() and be done with the whole mess.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The kernel_thread() changes for FRV don't work, and FRV fails to boot,
starting with:

	commit 02ce496f
	Author: Al Viro <viro@zeniv.linux.org.uk>
	Date:   Tue Sep 18 22:18:51 2012 -0400
	Subject: frv: split ret_from_fork, simplify kernel_thread() a lot

The problem is that the userspace registers are completely cleared when a
kernel thread is created and all subsequent user threads are then copied from
that.  Unfortunately, however, the TBR and PSR registers are restored from the
pt_regs and the values they should be set to are clobbered by the memset.

Instead, copy across the old user registers as normal, and then merely alter
GR8 and GR9 in it if we're going to execute a kernel thread.
Signed-off-by: David Howells <dhowells@redhat.com>

Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is
incorrectly loaded into the threadinfo flags rather than the threadinfo
preemption count.

Unfortunately, the code cannot be simply converted to use
preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to
cut down on the cost of actually disabling interrupts and thus
local_irq_enable() doesn't actually enable interrupts.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Al Viro <viro@ZenIV.linux.org.uk>

gcc-4.1.2 inlines weak functions, which causes FRV to fail when the dummy
thread_info_cache_init() gets inlined into start_kernel().
Signed-off-by: David Howells <dhowells@redhat.com>

Don't let objcopy transfer the GNU build_id note into the loadable image as it
is located at address 0 and the image ends up >3G in size.
Signed-off-by: David Howells <dhowells@redhat.com>

Add missing linux/export.h #inclusions to the FRV arch.
Signed-off-by: David Howells <dhowells@redhat.com>

Pull Xtensa fixes from Chris Zankel:
 "Some important bug fixes.

  With the change to uapi, there was a bug introduced that results in an
  empty syscall table (mult-inclusion bug).  Switching to the generic
  thread/execve allowed us to fix a bug we had in vfork()."

* tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux:
  xtensa: switch to generic sys_execve()
  xtensa: switch to generic kernel_execve()
  xtensa: switch to generic kernel_thread()
  xtensa: reset windowbase/windowstart when cloning the VM
  xtensa: use physical addresses for bus addresses
  xtensa: allow multi-inclusion for uapi/unistd.h