- 16 Apr, 2010 26 commits
-
-
Luis R. Rodriguez authored
Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
This allows us to add SREV checks on these helpers. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Luis R. Rodriguez authored
This add stubs for PHY support for the AR9003 hardware family. Signed-off-by:
-
Senthil Balasubramanian authored
Also, clean up and reorganize the AR9287 macro to have better ordering. We won't add the PCI ID to the supported device list until we have some functional code for it. Signed-off-by:
Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by:
-
Luis R. Rodriguez authored
The PLL control computation used to program the AR_RTC_PLL_CONTROL register varies between our harware so just add a private callback for it. AR9003 will use its own callback. Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
This is not required for the AR9003 family. Signed-off-by:
-
Luis R. Rodriguez authored
The PHY split is easier done in a few steps. First move the RF ops to the private ops and rename them accordingly. We split PHY stuff up first for the AR5008 and AR9002 families. There are some callbacks that AR9002 share with the AR5008 familiy so we set those first, if AR9002 has some different callbacks it will override them upon hardware init. Signed-off-by:
-
Luis R. Rodriguez authored
This is used only once by ath9k_hw_process_ini() to write an array of phy registers through REG_WRITE_ARRAY(), but we already call REG_WRITE_ARRAY() multiple times on the same caller so just remove this pointless wrapper. We'll eventually just move the ath9k_hw_process_ini() caller as an callback to abstract away between different hardware families. Although this change is subtle I should note that this does change the delay pattern on writing the next series of registers. REG_WRITE_ARRAY() uses a counter for each register write and does a udelay(1) every 64 writes. By removing this call it means that the counter is processed for all the iniBB_RfGain registers and is incremented on ath9k_hw_process_ini(), before this the after the call ath9k_hw_write_regs() was made the register counter was kept at the same index number prior to the call. Signed-off-by:
-
Luis R. Rodriguez authored
AR9003 does not have a reset control for AHB. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
This is not a stable code fix as this register is not used anywhere. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
AR9300 will be the first device supported of the AR9003 family. AR9300 1.0 hardware exists but it is not going to be sold anywhere so we completely skip its support. Signed-off-by:
-
Luis R. Rodriguez authored
ath9k supports the AR5008, AR9001 and AR9002 family of Atheros chipsets, all 802.11n. The new breed of 802.11n chips, the AR9003 family will be supported as well soon. To help with its support we're going to add a few callbacks for hardware routines which differ considerably instead of adding branch checks for the revision at runtime. Signed-off-by:
-
Dan Williams authored
Davinci platforms apparently need more time in-between helper firmware blocks. Even though this is an increased delay, we only take this hit once at initialization time. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Dan Williams authored
Consolidate a bunch of C&P code that waits for the firmware to be ready. Signed-off-by:
-
Larry Finger authored
In preparation for new rtl818x devices, move the existing rtl818x configuration into the rtl818x directory. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Acked-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by:
-
Grazvydas Ignotas authored
wl1251 is embedded chip that can be connected using SDIO bus, and is not an actual SDIO card. For this reason there is a need to pass some board specific data, like 'EEPROM is attached' flag or power control callback. However currently there is no way to pass this data through SDIO subsystem, so this patch registers dummy platform_device to allow that, until we have a better solution to this. Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Acked-by:
Kalle Valo <kvalo@adurom.com> Signed-off-by:
-
Christian Lamparter authored
This patch fixes a bug which was just recently introduced by ("p54pci: prevent stuck rx-ring on slow system"). make M=drivers/net/wireless/p54 C=2 CF=-D__CHECK_ENDIAN__ CHECK drivers/net/wireless/p54/p54pci.c drivers/net/wireless/p54/p54pci.c:143:11: warning: cast to restricted __le32 CC [M] drivers/net/wireless/p54/p54pci.o Reported-by:Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Xose Vazquez Perez authored
0x0e66,0x0009 HWUN2 Hawking Technologies Hi-Gain Wireless-150N USB Adapter w/ Upgradable Antenna 0x0e66,0x000b HWDN2 Hawking Technologies Hi-Gain USB Wireless-150N Dish Adapter 0x0e66,0x0013 Hawking Technologies Hi-Gain Wireless-N USB Adapter 0x0e66,0x0017 Hawking Wireless-N Network Adapter 0x0e66,0x0018 Hawking Wireless-N Network Adapter Hawking Technologies Technical Support guys say: All our N adapters use the same chipset. Ralink RT 2870 chipset. Signed-off-by:
Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Helmut Schaa authored
rt2800pci used the callback write_tx_desc to write the tx descriptor but also to update the txwi which is part of the dma mapped skb. Since the memory was already DMA mapped _before_ the call to write_tx_desc the device didn't get the txwi data at all or only sporadically. The call order is basically as follows (from rt2x00queue.c): 1) write_tx_data 2) rt2x00queue_map_txskb 3) write_tx_desc Hence, we shouldn't touch the skb in write_tx_desc anymore. To fix this issue create a new rt2800pci_write_tx_data callback and use it for updating the txwi _before_ the memory gets DMA mapped. The tx descriptor is still written (as before) in write_tx_desc. This patch allows basic TX on an rt305x soc device but I'm pretty sure that it will fix pci based cards as well. I can associate just fine with an AP now but I wasn't able to get a wpa secured connection working yet. Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
-
Helmut Schaa authored
Extend the write_tx_data callback with a txdesc parameter to allow access to the tx desciptor while preparing the tx data. Signed-off-by:
-
Nishant Sarmukadam authored
In a scenario, where a cfg80211 driver (station mode) does not send assoc request and assoc response IEs in cfg80211_connect_result after a successful association to an AP, cfg80211 sends IWEVASSOCREQIE and IWEVASSOCRESPIE to the user space application with NULL data. This can cause an issue at the event recipient. An example of this is when cfg80211 sends IWEVASSOCREQIE and IWEVASSOCRESPIE events with NULL event body to wpa_supplicant. The wpa_supplicant overwrites the assoc request and assoc response IEs for this station with NULL data. If the association is WPA/WPA2, the wpa_supplicant is not able to generate EAPOL handshake messages, since the IEs are NULL. With the patch, req_ie and resp_ie will be NULL by avoiding the assignment if the driver has not sent the IEs to cfg80211. The event sending code sends the events only if resp_ie and req_ie are not NULL. This will ensure that the events are not sent with NULL event body. Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Reviewed-by:
-
Grazvydas Ignotas authored
Some wl1251 hardware configurations (like in WG7210 module) have EEPROM attached where NVS data is kept, which includes MAC address. In such configurations, let's read default MAC address from EEPROM, instead of using random one. Signed-off-by:
-
- 14 Apr, 2010 9 commits
-
-
Xose Vazquez Perez authored
A very useful information was provided by Sitecom R&D guys: Please find the information regarding our latest Ralink adapters below; WL-302 - VID: 0x0DF6, PID: 0x002D - Ralink RT2771 WL-315 - VID: 0x0DF6, PID: 0x0039 - Ralink RT2770 WL-319 - VID: 0x182D, PID: 0x0037 - Ralink RT2860 WL-321 - VID: 0x0DF6, PID: 0x003B - Ralink RT2770 WL-324 - VID: 0x0DF6, PID: 0x003D - Ralink RT2870 WL-329 - VID: 0x0DF6, PID: 0x0041 - Ralink RT3572 WL-343 - VID: 0x0DF6, PID: 0x003E - Ralink RT3070 WL-344 - VID: 0x0DF6, PID: 0x0040 - Ralink RT3071 WL-345 - VID: 0x0DF6, PID: 0x0042 - Ralink RT3072 WL-608 - VID: 0x0DF6, PID: 0x003F - Ralink RT2070 Note: PID: 0x003C, 0x004A, and 0x004D: --these products do not exist; devices were never produced/shipped-- The WL-349v4 USB dongle (0x0df6,0x0050) will be shipped soon (it isn't available yet), and uses a Ralink RT3370 chipset. Signed-off-by:
-
Christian Lamparter authored
This patch adds the following 5 entries to the usbid device table: * Netgear WNA1000 * Proxim ORiNOCO Dual Band 802.11n USB Adapter * 3Com Dual Band 802.11n USB Adapter * H3C Dual Band 802.11n USB Adapter * WNC Generic 11n USB dongle CC: <stable@kernel.org> Signed-off-by:
-
Grazvydas Ignotas authored
If EEPROM is used, NVS data is now loaded but ignored. Stop loading it to avoid need of dummy NVS file for modules with EEPROM. Signed-off-by:
-
Ming Lei authored
This patch fixes two warnings below after unplugging ar9271 usb device: -one is a kernel warning[1] -another is a lockdep warning[2] The root reason is that __skb_queue_purge can't be executed in hardirq context, so the patch forks ath9k_skb_queue_purge(ath9k version of _skb_queue_purge), which frees skb with dev_kfree_skb_any which can be run in hardirq context safely, then prevent the lockdep warning and kernel warning after unplugging ar9271 usb device. [1] kernel warning [ 602.894005] ------------[ cut here ]------------ [ 602.894005] WARNING: at net/core/skbuff.c:398 skb_release_head_state+0x71/0x87() [ 602.894005] Hardware name: 6475EK2 [ 602.894005] Modules linked in: ath9k_htc ath9k ath9k_common ath9k_hw ath bridge stp llc sunrpc ipv6 cpufreq_ondemand acpi_cpufreq freq_table kvm_intel kvm arc4 ecb mac80211 snd_hda_codec_conexant snd_hda_intel snd_hda_codec snd_hwdep thinkpad_acpi snd_pcm snd_timer hwmon iTCO_wdt snd e1000e pcspkr i2c_i801 usbhid iTCO_vendor_support wmi cfg80211 yenta_socket rsrc_nonstatic pata_acpi snd_page_alloc soundcore uhci_hcd ohci_hcd ehci_hcd usbcore i915 drm_kms_helper drm i2c_algo_bit i2c_core video output [last unloaded: ath] [ 602.894005] Pid: 2506, comm: ping Tainted: G W 2.6.34-rc3-wl #20 [ 602.894005] Call Trace: [ 602.894005] <IRQ> [<ffffffff8104a41c>] warn_slowpath_common+0x7c/0x94 [ 602.894005] [<ffffffffa022f398>] ? __skb_queue_purge+0x43/0x4a [ath9k_htc] [ 602.894005] [<ffffffff8104a448>] warn_slowpath_null+0x14/0x16 [ 602.894005] [<ffffffff813269c1>] skb_release_head_state+0x71/0x87 [ 602.894005] [<ffffffff8132829a>] __kfree_skb+0x16/0x81 [ 602.894005] [<ffffffff813283b2>] kfree_skb+0x7e/0x86 [ 602.894005] [<ffffffffa022f398>] __skb_queue_purge+0x43/0x4a [ath9k_htc] [ 602.894005] [<ffffffffa022f560>] __hif_usb_tx+0x1c1/0x21b [ath9k_htc] [ 602.894005] [<ffffffffa022f73c>] hif_usb_tx_cb+0x12f/0x154 [ath9k_htc] [ 602.894005] [<ffffffffa00d2fbe>] usb_hcd_giveback_urb+0x91/0xc5 [usbcore] [ 602.894005] [<ffffffffa00f6c34>] ehci_urb_done+0x7a/0x8b [ehci_hcd] [ 602.894005] [<ffffffffa00f6f33>] qh_completions+0x2ee/0x376 [ehci_hcd] [ 602.894005] [<ffffffffa00f8ba5>] ehci_work+0x95/0x76e [ehci_hcd] [ 602.894005] [<ffffffffa00fa5ae>] ? ehci_irq+0x2f/0x1d4 [ehci_hcd] [ 602.894005] [<ffffffffa00fa725>] ehci_irq+0x1a6/0x1d4 [ehci_hcd] [ 602.894005] [<ffffffff810a6d18>] ? __rcu_process_callbacks+0x7a/0x2df [ 602.894005] [<ffffffff810a47a4>] ? handle_fasteoi_irq+0x22/0xd2 [ 602.894005] [<ffffffffa00d268d>] usb_hcd_irq+0x4a/0xa7 [usbcore] [ 602.894005] [<ffffffff810a2853>] handle_IRQ_event+0x77/0x14f [ 602.894005] [<ffffffff813285ce>] ? skb_release_data+0xc9/0xce [ 602.894005] [<ffffffff810a4814>] handle_fasteoi_irq+0x92/0xd2 [ 602.894005] [<ffffffff8100c4fb>] handle_irq+0x88/0x91 [ 602.894005] [<ffffffff8100baed>] do_IRQ+0x63/0xc9 [ 602.894005] [<ffffffff81354245>] ? ip_flush_pending_frames+0x4d/0x5c [ 602.894005] [<ffffffff813ba993>] ret_from_intr+0x0/0x16 [ 602.894005] <EOI> [<ffffffff811095fe>] ? __delete_object+0x5a/0xb1 [ 602.894005] [<ffffffff813ba5f5>] ? _raw_write_unlock_irqrestore+0x47/0x7e [ 602.894005] [<ffffffff813ba5fa>] ? _raw_write_unlock_irqrestore+0x4c/0x7e [ 602.894005] [<ffffffff811095fe>] __delete_object+0x5a/0xb1 [ 602.894005] [<ffffffff81109814>] delete_object_full+0x25/0x31 [ 602.894005] [<ffffffff813a60c0>] kmemleak_free+0x26/0x45 [ 602.894005] [<ffffffff810ff517>] kfree+0xaa/0x149 [ 602.894005] [<ffffffff81323fb7>] ? sock_def_write_space+0x84/0x89 [ 602.894005] [<ffffffff81354245>] ? ip_flush_pending_frames+0x4d/0x5c [ 602.894005] [<ffffffff813285ce>] skb_release_data+0xc9/0xce [ 602.894005] [<ffffffff813282a2>] __kfree_skb+0x1e/0x81 [ 602.894005] [<ffffffff813283b2>] kfree_skb+0x7e/0x86 [ 602.894005] [<ffffffff81354245>] ip_flush_pending_frames+0x4d/0x5c [ 602.894005] [<ffffffff81370c1f>] raw_sendmsg+0x653/0x709 [ 602.894005] [<ffffffff81379e31>] inet_sendmsg+0x54/0x5d [ 602.894005] [<ffffffff813207a2>] ? sock_recvmsg+0xc6/0xdf [ 602.894005] [<ffffffff813208c1>] sock_sendmsg+0xc0/0xd9 [ 602.894005] [<ffffffff810e13b4>] ? might_fault+0x68/0xb8 [ 602.894005] [<ffffffff810e13fd>] ? might_fault+0xb1/0xb8 [ 602.894005] [<ffffffff8132a1c3>] ? copy_from_user+0x2f/0x31 [ 602.894005] [<ffffffff8132a5b3>] ? verify_iovec+0x54/0x91 [ 602.894005] [<ffffffff81320d41>] sys_sendmsg+0x1da/0x241 [ 602.894005] [<ffffffff8103d327>] ? finish_task_switch+0x0/0xc9 [ 602.894005] [<ffffffff8103d327>] ? finish_task_switch+0x0/0xc9 [ 602.894005] [<ffffffff8107642e>] ? trace_hardirqs_on_caller+0x16/0x150 [ 602.894005] [<ffffffff813ba27d>] ? _raw_spin_unlock_irq+0x56/0x63 [ 602.894005] [<ffffffff8103d3cb>] ? finish_task_switch+0xa4/0xc9 [ 602.894005] [<ffffffff8103d327>] ? finish_task_switch+0x0/0xc9 [ 602.894005] [<ffffffff810357fe>] ? need_resched+0x23/0x2d [ 602.894005] [<ffffffff8107642e>] ? trace_hardirqs_on_caller+0x16/0x150 [ 602.894005] [<ffffffff813b9750>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 602.894005] [<ffffffff81009c02>] system_call_fastpath+0x16/0x1b [ 602.894005] ---[ end trace 91ba2d8dc7826839 ]--- [2] lockdep warning [ 169.363215] ====================================================== [ 169.365390] [ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ] [ 169.366334] 2.6.34-rc3-wl #20 [ 169.366872] ------------------------------------------------------ [ 169.366872] khubd/78 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 169.366872] (clock-AF_INET){++.?..}, at: [<ffffffff81323f51>] sock_def_write_space+0x1e/0x89 [ 169.366872] [ 169.366872] and this task is already holding: [ 169.366872] (&(&hif_dev->tx.tx_lock)->rlock){-.-...}, at: [<ffffffffa03715b0>] hif_usb_stop+0x24/0x53 [ath9k_htc] [ 169.366872] which would create a new lock dependency: [ 169.366872] (&(&hif_dev->tx.tx_lock)->rlock){-.-...} -> (clock-AF_INET){++.?..} [ 169.366872] [ 169.366872] but this new dependency connects a HARDIRQ-irq-safe lock: [ 169.366872] (&(&hif_dev->tx.tx_lock)->rlock){-.-...} [ 169.366872] ... which became HARDIRQ-irq-safe at: [ 169.366872] [<ffffffff810772d5>] __lock_acquire+0x2c6/0xd2b [ 169.366872] [<ffffffff8107866d>] lock_acquire+0xec/0x119 [ 169.366872] [<ffffffff813b99bb>] _raw_spin_lock+0x40/0x73 [ 169.366872] [<ffffffffa037163d>] hif_usb_tx_cb+0x5e/0x154 [ath9k_htc] [ 169.366872] [<ffffffffa00d2fbe>] usb_hcd_giveback_urb+0x91/0xc5 [usbcore] [ 169.366872] [<ffffffffa00f6c34>] ehci_urb_done+0x7a/0x8b [ehci_hcd] [ 169.366872] [<ffffffffa00f6f33>] qh_completions+0x2ee/0x376 [ehci_hcd] [ 169.366872] [<ffffffffa00f8ba5>] ehci_work+0x95/0x76e [ehci_hcd] [ 169.366872] [<ffffffffa00fa725>] ehci_irq+0x1a6/0x1d4 [ehci_hcd] [ 169.366872] [<ffffffffa00d268d>] usb_hcd_irq+0x4a/0xa7 [usbcore] [ 169.366872] [<ffffffff810a2853>] handle_IRQ_event+0x77/0x14f [ 169.366872] [<ffffffff810a4814>] handle_fasteoi_irq+0x92/0xd2 [ 169.366872] [<ffffffff8100c4fb>] handle_irq+0x88/0x91 [ 169.366872] [<ffffffff8100baed>] do_IRQ+0x63/0xc9 [ 169.366872] [<ffffffff813ba993>] ret_from_intr+0x0/0x16 [ 169.366872] [<ffffffff8130f6ee>] cpuidle_idle_call+0xa7/0x115 [ 169.366872] [<ffffffff81008c4f>] cpu_idle+0x68/0xc4 [ 169.366872] [<ffffffff813a41e0>] rest_init+0x104/0x10b [ 169.366872] [<ffffffff81899db3>] start_kernel+0x3f1/0x3fc [ 169.366872] [<ffffffff818992c8>] x86_64_start_reservations+0xb3/0xb7 [ 169.366872] [<ffffffff818993c4>] x86_64_start_kernel+0xf8/0x107 [ 169.366872] [ 169.366872] to a HARDIRQ-irq-unsafe lock: [ 169.366872] (clock-AF_INET){++.?..} [ 169.366872] ... which became HARDIRQ-irq-unsafe at: [ 169.366872] ... [<ffffffff81077349>] __lock_acquire+0x33a/0xd2b [ 169.366872] [<ffffffff8107866d>] lock_acquire+0xec/0x119 [ 169.366872] [<ffffffff813b9d07>] _raw_write_lock_bh+0x45/0x7a [ 169.366872] [<ffffffff8135cf14>] tcp_close+0x165/0x34d [ 169.366872] [<ffffffff8137aced>] inet_release+0x55/0x5c [ 169.366872] [<ffffffff81321350>] sock_release+0x1f/0x6e [ 169.366872] [<ffffffff813213c6>] sock_close+0x27/0x2b [ 169.366872] [<ffffffff8110dd45>] __fput+0x125/0x1ca [ 169.366872] [<ffffffff8110de04>] fput+0x1a/0x1c [ 169.366872] [<ffffffff8110adc9>] filp_close+0x68/0x72 [ 169.366872] [<ffffffff8110ae80>] sys_close+0xad/0xe7 [ 169.366872] [<ffffffff81009c02>] system_call_fastpath+0x16/0x1b (Trimmed at the "other info that might help us debug this" line in the interest of brevity... -- JWL) Signed-off-by:Ming Lei <tom.leiming@gmail.com> Acked-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Ming Lei authored
In ath9k-htc register out path, ath9k-htc will pass skb->data into usb hcd and usb hcd will do dma mapping and unmapping to the buffer pointed by skb->data, so we should pass a cache-line aligned address. This patch replace __dev_alloc_skb with alloc_skb to make skb->data pointed to a cacheline aligned address simply since ath9k-htc does not skb_push on the skb and pass it to mac80211, also use kfree_skb to free the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq context since skb->destructor is NULL always in the path). Signed-off-by:
-
Ming Lei authored
In ath9k-htc register in path, ath9k-htc will pass skb->data into usb hcd and usb hcd will do dma mapping and unmapping to the buffer pointed by skb->data, so we should pass a cache-line aligned address. This patch replace __dev_alloc_skb with alloc_skb to make skb->data pointed to a cacheline aligned address simply since ath9k-htc does not skb_push on the skb and pass it to mac80211, also use kfree_skb to free the skb allocated by alloc_skb(we can use kfree_skb safely in hardirq context since skb->destructor is NULL always in the path). Signed-off-by:
-
Ming Lei authored
In ath9k_hif_usb_alloc_rx_urbs, ath9k-htc will pass skb->data into usb hcd and usb hcd will do dma mapping and unmapping to the buffer pointed by skb->data, so we should pass a cache-line aligned address. This patch replace __dev_alloc_skb with alloc_skb to make skb->data pointed to a cacheline aligned address simply since ath9k-htc does not skb_push on the skb and pass it to mac80211, also use kfree_skb to free the skbs allocated by alloc_skb(we can use kfree_skb safely in hardirq context since skb->destructor is NULL always in the path). Signed-off-by:
-
Bruno Randolf authored
We get RXORN interrupts when all receive buffers are full. This is not necessarily a fatal situation. It can also happen when the bus is busy or the CPU is not fast enough to process all frames. Older chipsets apparently need a reset to come out of this situration, but on newer chips we can treat RXORN like RX, as going thru a full reset does more harm than good, there. The exact chip revisions which need a reset are unknown - this guess AR5K_SREV_AR5212 ("venice") is copied from the HAL. Inspired by openwrt 413-rxorn.patch: "treat rxorn like rx, reset after rxorn seems to do more harm than good" Signed-off-by:Bruno Randolf <br1@einfach.org> Signed-off-by:
-
Bruno Randolf authored
There was a confusion in the usage of the bits AR5K_STA_ID1_ACKCTS_6MB and AR5K_STA_ID1_BASE_RATE_11B. If they are set (1), we will get lower bitrates for ACK and CTS. Therefore ath5k_hw_set_ack_bitrate_high(ah, false) actually resulted in high bitrates, which i think is what we want anyways. Cleared the confusion and added some documentation. Signed-off-by:
-
- 12 Apr, 2010 5 commits
-
-
Gertjan van Wingerde authored
Add RT3390 specific register initializations to rt2x00, based on the latest Ralink rt3390 vendor driver. Untested as I don't actually own an RT3390 based device, but given experiences on rt3070/rt3071 very hopeful that this will actually work.. Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Gertjan van Wingerde authored
Add RT3090 specific register initializations to rt2x00, based on the latest Ralink rt3090 vendor driver. Untested as I don't actually own an RT3090 based device, but given experiences on rt3070/rt3071 very hopeful that this will actually work.. Signed-off-by:
-
Gertjan van Wingerde authored
Add RT3071 specific register initializations to rt2x00, based on the latest Ralink rt3070 vendor driver. With this patch my RT3071 based devices start showing a sign of life. Signed-off-by:
-
Gertjan van Wingerde authored
rt2x00 had preliminary support for RT3070 based devices, but the support was incomplete. Update the RT3070 register initialization to be similar to the latest Ralink vendor driver. With this patch my rt3070 based devices start showing a sign of life. Signed-off-by:
-
Gertjan van Wingerde authored
Align the rt2800 register initializations with the latest versions of the Ralink vendor driver. This patch is also preparation for the addition of support for RT3070 / RT3071 / RT3090 / RT3390 based devices. Signed-off-by:
-
