Signed-off-by: Jaroslav Kysela <perex@suse.cz>

STAC922x provides the capture boost level up to 4, but actually it
works only up to 2.  Since the range of the mixer is automatically
defined from amp-capability bits, we need to override the value
beforehand.  snd_hda_override_amp_caps() is introduced for this
purpose.
The function patch_stac922x() calls this for NID 0x12 (Mux Capture
Volume).  This should fix another recording problem on Intel Macs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

The recent fix for STAC92xx surround outputs broke the input pin
setting for shared line-in and mic jacks.  This patch fixes the
breakage.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

Fix pin default configs for speaker associations and sequence
for Gateway MX6453 machine with STAC925x codecs.
Signed-off-by: Steve Longerbeam <stevel@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

This patch adds the MSI K9N Ultra system to the realtek patch.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

Tested and verified in #alsa/Freenode on Tuesday, May 29, 2007.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: crimsun@Box.ncat.edu
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

Add a quirk for MSI S420 (based on a guess work).
From: Baruch Even <baruch@ev-en.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

This should fix a spinlock lockup bug on the s3c24xx arch.
From: Zoltan Devai <zdevai@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

Commit f32610ed added ALC660VD support, but
this caused a 2.6.21 regression for some users. The ASUS M2V device is
now detected as ALC660VD rather than ALC660/861 but the PCI quirk was not
carried over.
This patch allows affected users to use audio again.
http://bugzilla.kernel.org/show_bug.cgi?id=8273
https://bugs.gentoo.org/show_bug.cgi?id=178243Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

Reported by Eric Sesterhenn.
Fix the wrong checks of extra voice pointer, which may cause NULL
dereferences.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

This patch adds support for the ASUS A8J Series 56k Modem (Motorola SM56)
Signed-off-by: Christian Rothlaender <christian@rothlaender.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

This patch fixes an automute code issue for systems that do not rely
on eapd support.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

This patch adds more Dell systems and a Panasonic laptop with
STAC9200 codecs.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

This patch adds support for the Gateway NX860 system.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>

It should be pass "newsize" to vmtruncate function to modify the
inode->i_size, while the old size is passed to vmtruncate.

This bug was caught by LTP truncate test case on Blackfin platform.
After it was fixed, the LTP truncate test case passed.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The current code is leaking a reference to dreq->kref when the calls to
nfs_direct_read_schedule() and nfs_direct_write_schedule() return an
error.
This patch moves the call to kref_put() from nfs_direct_wait() back into
nfs_direct_read() and nfs_direct_write() (which are the functions that
actually took the reference in the first place) fixing the leak.

Thanks to Denis V. Lunev for spotting the bug and proposing the original
fix.
Acked-by: Denis V. Lunev <dlunev@gmail.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>

ugh, this function gets called by our unwinder. recursive backtrace for
the win... bisection to find this one was "fun."
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some of the new syscalls require supporting TIF_RESTORE_SIGMASK.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove 2 functions private to the alpha implemetation,
in favor of similar functions in <linux/log2.h>.

Provide a more efficient version of the fls64 function
for pre-ev67 alphas.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] Fix some section mismatch warnings
  [ARM] 4417/1: Serial: Fix AMBA drivers locking
  [ARM] 4394/1: ARMv7: Add the TLB range operations
  [ARM] 4410/1: Remove extern declarations in coyote/ixdpg425-pci.c
  [ARM] 4416/1: NWFPE: fix undeclared symbols
  [ARM] 4415/1: AML5900: fix sparse warnings from map_io
  [ARM] 4414/1: S3C2443: sparse fix for clock.c
  [ARM] 4412/1: S3C2412: reset errata fix
  [ARM] 4411/1: KS8695: Another serial driver fix
  [ARM] oprofile: avoid lockdep warnings on mpcore oprofile init
  [ARM] Fix stacktrace FP range checking
  [ARM] use __used attribute
  [ARM] enable arbitary speed tty ioctls and split input/output speed
  [ARM] remove unused header file: arch/arm/mach-s3c2410/bast.h
  [ARM] 4406/1: Trivial NSLU2 / NAS-100D header & setup code cleanup
  [ARM] 4405/1: NSLU2, DSM-G600 frequency fixup code
  [ARM] 4404/1: Trivial IXP42x Kconfig cleanup
  [ARM] 4403/1: Make the PXA-I2C driver work with lockdep validator
  [ARM] 4402/1: S3C2443: Add physical address of HSMMC controller
  [ARM] 4401/1: S3C2443: Add definitions for port GPIOJ

The following patch fixes these section mismatch warnings:

WARNING: arch/arm/mach-at91/built-in.o(.text+0xdf4): Section mismatch: reference to .init.data:dk_nand_partition (between 'nand_partitions' and 'at91_leds_event')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (between 'nand_partitions' and 'ads7843_pendown_state')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xbdc): Section mismatch: reference to .init.data:ek_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-at91/built-in.o(.text+0xc28): Section mismatch: reference to .init.data:kb9202_nand_partition (after 'nand_partitions')
WARNING: arch/arm/mach-footbridge/built-in.o(.text+0xaa4): Section mismatch: reference to .init.data:cats_pci (between 'cats_pci_init' and 'ebsa285_leds_event')WARNING: arch/arm/mach-ixp2000/built-in.o(.text+0xb54): Section mismatch: reference to .init.text:ixp2000_init_irq (between 'ixdp2x00_init_irq' and 'ixdp2x00_irq_handler')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x670): Section mismatch: reference to .init.text:ixp23xx_pci_common_init (between 'ixp23xx_pci_slave_init' and 'ixp23xx_pci_scan_bus')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x890): Section mismatch: reference to .init.text:ixp23xx_init_irq (between 'ixdp2351_init_irq' and 'roadrunner_pci_preinit')
WARNING: arch/arm/mach-ixp23xx/built-in.o(.text+0x9a8): Section mismatch: reference to .init.text:ixp23xx_pci_preinit (after 'roadrunner_pci_preinit')
WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x80): Section mismatch: reference to .init.text:imx_set_mmc_info (between '__ksymtab_imx_set_mmc_info' and '__ksymtab_set_imx_fb_info')
WARNING: arch/arm/mach-imx/built-in.o(__ksymtab+0x88): Section mismatch: reference to .init.text:set_imx_fb_info (after '__ksymtab_set_imx_fb_info')
WARNING: arch/arm/mach-sa1100/built-in.o(.text+0x1930): Section mismatch: reference to .init.data:neponset_port_fns (between 'neponset_probe' and 'assabet_leds_event')
WARNING: drivers/built-in.o(.text+0x3f100): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x3f1c8): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x4f988): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
WARNING: drivers/built-in.o(.text+0x4fa50): Section mismatch: reference to .init.text:ps2_clear_input (between 'ps2_probe' and 'ps2_cmd_aborted')
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  ehea: Fixed multi queue RX bug
  sky2: enable IRQ on duplex renegotiation
  e1000: restore netif_poll_enable call but make sure IRQs are off
  defxx: Fix the handling of ioremap() failures
  sky2: program proper register for fiber PHY
  sky2: checksum offload plus vlan bug
  sky2: dont set bogus bit in PHY register
  [PATCH] hostap: Allocate enough tailroom for TKIP
  [PATCH] softmac: alloc_ieee80211() NULL check
  [PATCH] ieee80211: fix incomplete error message
  [PATCH] prism54: fix monitor mode oops

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] Write at EOF may not update filesize correctly.

Must access the respective queue's dummy netdev instead of the port's netdev.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Don't want IRQ on FIFO error because there is nothing useful to do with it.
But do want IRQ on duplex change.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This restores the previously removed netif_poll_enable call in e1000_open.
It's needed on all but the first call to e1000_open for a NIC as
e1000_close always calls netif_poll_disable.

netif_poll_enable can only be called safely if no polls have been
scheduled.  This should be the case as long as we don't enter our IRQ
handler.

In order to guarantee this we explicitly disable IRQs as early as possible
when we're probing the NIC.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Kok, Auke" <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

 If ioremap_nocache() is unfortunate enough to fail, the error code is not
set correctly leading to a false success from dfx_register().  This change
fixes the problem.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Driver was reading value from one register, setting bit and then
writing the wrong register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Driver was not correctly setting up transmit descriptor when doing
VLAN tag insertion with checksum offload.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This code inherited from the sk98lin driver is incorrect on the Yukon2.
The GPHY_CTRL register values are specific to the internal PHY of the chip
and the values used were leftovers.
Driver was setting bit 13 which is now the INT polarity for the PHY!
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes

The -rt patch triggered a lockdep warning in the amba serial drivers, which never
shows up on UP kernels. On SMP systems this would trigger as well.

Release the port lock before calling tty_flip_buffer_push() and reacquire it after
the call. This matches the code in the 8250 serial driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We are currently using the ARMv6 operations but need to duplicate some
of the code because of the introduction of the new CPU barrier
instructions in ARMv7.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch removes apparently unnecessary extern declarations in
coyote-pci.c and ixdpg425-pci.c within arch/arm/mach-ixp4xx and
has been compile-tested without producing warnings or errors.

Kernel coding style forbids the use of extern declarations within .c
files.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix the undeclared symbols sparse is warning about.

arch/arm/nwfpe/softfloat.c:1727:7: warning: symbol 'float64_to_uint32' was not declared. Should it be static?
arch/arm/nwfpe/softfloat.c:1753:7: warning: symbol 'float64_to_uint32_round_to_zero' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The map_io function does not need to be exported
from this file, and therefore should be declared
static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix sparse warnings in the arch/arm/mach-s3c2443/clock.c,
including an bug in initialising the cf clock initialiser
where two values are being set for the ctrlbit.

arch/arm/mach-s3c2443/clock.c:397:12: warning: symbol 'clk_usb_bus_host' was not declared. Should it be static?
arch/arm/mach-s3c2443/clock.c:760:4: error: Initializer entry defined twice
arch/arm/mach-s3c2443/clock.c:761:4:   also defined here
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The S3C2412 has an reset-errata where the clock
may cause a glitch switching back to EXTCLK. We
force a switch to EXTCLK before writing the
reset register to force use of the CLKCON sync
logic to properly switch.

Fix problem reported by Matthieu Castet.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix a error reported by newer versions of GCC.
error: static declaration of 'ks8695_reg' follows non-static declaration
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix lockdep warnings, caused by 'set_affinity' being called without
the correct locks taken and local interrupts disabled:

=================================
[ INFO: inconsistent lock state ]
2.6.22-rc2 #1
---------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
swapper/1 [HC0[0]:SC0[0]:HE1:SE1] takes:
(irq_controller_lock){++..}, at: [<c002be50>] gic_set_cpu+0x60/0xa0
{in-hardirq-W} state was registered at:
 [<c005d9a8>] lock_acquire+0x58/0x6c
 [<c0233068>] _spin_lock+0x40/0x50
 [<c002c020>] gic_mask_irq+0x2c/0x6c
 [<c0069c64>] handle_level_irq+0x11c/0x14c
 [<c0020060>] asm_do_IRQ+0x60/0x84
 [<c0020d2c>] __irq_svc+0x4c/0xc0
 [<c000ed84>] __alloc_bootmem_nopanic+0x74/0x88
 [<c000edb0>] __alloc_bootmem+0x18/0x3c
 [<c000fa00>] alloc_large_system_hash+0x16c/0x200
 [<c00108dc>] inode_init_early+0x5c/0xa4
 [<c00106dc>] vfs_caches_init_early+0x24/0xa0
 [<c0008e54>] start_kernel+0x220/0x2fc
 [<00008078>] 0x8078
irq event stamp: 88438
hardirqs last  enabled at (88438): [<c0020dc0>] preempt_return+0x20/0x2c
hardirqs last disabled at (88436): [<c00417bc>] __do_softirq+0xb0/0x138
softirqs last  enabled at (88437): [<c0041810>] __do_softirq+0x104/0x138
softirqs last disabled at (88428): [<c0041d9c>] irq_exit+0x68/0x7c

other info that might help us debug this:
no locks held by swapper/1.

stack backtrace:
[<c0025ecc>] (dump_stack+0x0/0x14) from [<c005b1e4>] (print_usage_bug+0x138/0x168)
[<c005b0ac>] (print_usage_bug+0x0/0x168) from [<c005be80>] (mark_lock+0x484/0x6a0)
[<c005b9fc>] (mark_lock+0x0/0x6a0) from [<c005cc48>] (__lock_acquire+0x3c0/0x10c8)
[<c005c888>] (__lock_acquire+0x0/0x10c8) from [<c005d9a8>] (lock_acquire+0x58/0x6c)
[<c005d950>] (lock_acquire+0x0/0x6c) from [<c0233068>] (_spin_lock+0x40/0x50)
[<c0233028>] (_spin_lock+0x0/0x50) from [<c002be50>] (gic_set_cpu+0x60/0xa0)
[<c002bdf0>] (gic_set_cpu+0x0/0xa0) from [<c01b04cc>] (em_route_irq+0x38/0x40)
[<c01b0494>] (em_route_irq+0x0/0x40) from [<c01b04ec>] (em_setup+0x18/0xa4)
[<c01b04d4>] (em_setup+0x0/0xa4) from [<c001570c>] (oprofile_arch_init+0x24/0xe8)
[<c00156e8>] (oprofile_arch_init+0x0/0xe8) from [<c0015640>] (oprofile_init+0x1c/0x64)
[<c0015624>] (oprofile_init+0x0/0x64) from [<c0008a20>] (kernel_init+0x154/0x368)
[<c00088cc>] (kernel_init+0x0/0x368) from [<c003ef34>] (do_exit+0x0/0x904)
oprofile: using arm/mpcore
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>