Document the settings exported by max77693 charger driver through sysfs
entries:
 - fast_charge_timer
 - top_off_threshold_current
 - top_off_timer
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Add new driver for Maxim 77693 switch-mode charger (part of max77693
MFD driver) providing power supply class information to userspace.

The charger has +20V tolerant input. Current input can be set from 0 to
2.58 A. The charger can deliver up to 2.1 A to the battery or 3.5 A to
the system (when supplying additional current from battery to system).

The driver is configured through DTS (battery and system related
settings) and sysfs entries (timers and top-off charging threshold).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Prepare for adding support for Maxim 77693 charger by adding necessary
new defines.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Document new device tree bindings for Maxim 77693 charger driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The driver mismatched 'num_supplicants' with 'num_supplies' of
power_supply structure.

It provided list of supplicants (power_supply.supplied_to) but did
not set the number of supplicants. Instead it set the num_supplies which
is used when iterating over number of supplies (power_supply.supplied_from).

As a result the list of supplicants was ignored by core because its size
was 0.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: d7bf353f ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Teach collie_battery driver to communicate to the kernel that it can
generate wakeup events. Handle enabling/disabling wakeup on battery full
event in suspend/resume callbacks.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

enable_irq_wakeup returns 0 in case it correctly enabled the IRQ to
generate the wakeup event (and thus resume should call disable_irq_wake).
Currently gpio-charger driver has this logic inverted. Correct that thus
correcting enable/disable_irq_wake() calls balance.

Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This patch adds device driver of Richtek PMIC.
The driver support battery fuel gauge. Fuel gauge calculates and determines the
battery state of charge (SOC) according to battery open circuit voltage (OCV).
Also, this driver provides battery average voltage, voltage and battery present
property.

Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Document the fact that the trigger signal is now optional, and describe
the behavior when this is used.

While at it, fix a typo, and paraphrase a sentence to be less platform
specific.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Currently the ltc2952 supports only one button sequence to initiate
powerdown. This is not always desirable, as even prolonged button
presses can happen in use.

Allow ltc2952 users to pick their own power down sequence, by making the
trigger input optional. Since this still means that the ltc2952 may
power down the platform if the power button is pressed for about 5
seconds, we still need to make sure to start the watchdog toggle to
prolong the system power for as long as we need it.

This will still allow the system to control power using the kill signal.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

In ltc2952_poweroff_handler it is theoretically possible that the timer
fails to start on first pass (button press), but succeeds in starting on
the second (button release). This will cause the button press to be
misinterpreted, and will incorrectly shut down the system. Because a
picture says more than a thousand words:

Expected behavior:
tmr:      ++++++++++
btn: -----__________-----

Faulty behavior:
tmr:                +++++
btn: -----__________-----

Legend:
+ timer runs
_ button pressed
- button depressed

To prevent this from happening, check the value of the gpio before
starting the timer. If the button is active, we should start the timer,
else we should stop it.

The situation described can now still occur if the polarity of the input
pin is set incorrectly, but that at least is predictable behavior and
can be detected during the first tests.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Disable the timers when ltc2952_poweroff is removed. We don't want to
risk calling functions on data that no longer exist.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The function pointers for the timers and pm_power_off are assigned with
C++ style
	foo = &func;

Let's change it instead to the more C style
	foo = func;
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

ltc2952_poweroff_handler uses gotos to return from the function. Since
we don't do cleanups exiting this function, just return IRQ_HANDLED on
the spot and be done with it.

While at it, remove the variable 'ret'. It was never used very much.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Documentation/SubmittingDrivers suggests these be implemented even when
they do nothing. On the other hand, the platform code calls these
functions 'legacy'. Suspend and resume operations should go into a
pm_ops structure, pointed at by the driver's pm field. This approach
would lead to a lot of boiler plate, while achieving nothing. Drop the
functions instead.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

As per Documentation/CodingStyle ch.4, we should keep global variables
to a mininum. Move the panic state into the driver data, regardless of
whether panic is a system state or not.

This removes the need for the custom _init and _exit functions, so
replace them with a call to the module_platform_driver() macro.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Documentation/CodingStyle ch.4 mentions in a side node that global
variables should only be used if you really need them. Reduce the use of
the global instance of ltc2952_poweroff so we may eventually remove it
entirely.

While at it, rename ltc2952_poweroff_data to ltc2952_poweroff, just to
save that little bit of typing.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

This reduces cleanup code and chance of errors.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

The three gpio's used by this driver are stored in an array of pointers.
This doesn't add much besides cleanups in a loop. In fact, it makes most
of the usage sites harder to read. Unroll the loop, and live with the
fact that cleanups become slightly larger.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Make use of the fact that we allocated resources can be automatically
deallocated. This reduces cleanup code and chance of errors. It also
removes the need for the virq member of the ltc2952_poweroff_data
struct.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Make use of the fact that the allocated resources can be automatically
deallocated. This reduces cleanup code and chance of leaks.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Augment the Versatile reset driver to also handle the core
module reset sequence used on the Integrator/AP and
Integrator/CP.

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Pull pin control fixes from Linus Walleij:
 "Here is a (hopefully final) slew of pin control fixes for the v3.19
  series.  The deadlock fix is kind of serious and tagged for stable,
  the rest is business as usual.

   - Fix two deadlocks around the pin control mutexes, a long-standing
     issue that manifest itself in plug/unplug of pin controllers.
     (Tagged for stable.)

   - Handle an error path with zero functions in the Qualcomm pin
     controller.

   - Drop a bogus second GPIO chip added in the Lantiq driver.

   - Fix sudden IRQ loss on Rockchip pin controllers.

   - Register the GIT tree in MAINTAINERS"

* tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: MAINTAINERS: add git tree reference
  pinctrl: qcom: Don't iterate past end of function array
  pinctrl: lantiq: remove bogus of_gpio_chip_add
  pinctrl: Fix two deadlocks
  pinctrl: rockchip: Avoid losing interrupts when supporting both edges

Pull networking fixes from David Miller:

 1) Socket addresses returned in the error queue need to be fully
    initialized before being passed on to userspace, fix from Willem de
    Bruijn.

 2) Interrupt handling fixes to davinci_emac driver from Tony Lindgren.

 3) Fix races between receive packet steering and cpu hotplug, from Eric
    Dumazet.

 4) Allowing netlink sockets to subscribe to unknown multicast groups
    leads to crashes, don't allow it.  From Johannes Berg.

 5) One to many socket races in SCTP fixed by Daniel Borkmann.

 6) Put in a guard against the mis-use of ipv6 atomic fragments, from
    Hagen Paul Pfeifer.

 7) Fix promisc mode and ethtool crashes in sh_eth driver, from Ben
    Hutchings.

 8) NULL deref and double kfree fix in sxgbe driver from Girish K.S and
    Byungho An.

 9) cfg80211 deadlock fix from Arik Nemtsov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
  s2io: use snprintf() as a safety feature
  r8152: remove sram_read
  r8152: remove generic_ocp_read before writing
  bgmac: activate irqs only if there is nothing to poll
  bgmac: register napi before the device
  sh_eth: Fix ethtool operation crash when net device is down
  sh_eth: Fix promiscuous mode on chips without TSU
  ipv6: stop sending PTB packets for MTU < 1280
  net: sctp: fix race for one-to-many sockets in sendmsg's auto associate
  genetlink: synchronize socket closing and family removal
  genetlink: disallow subscribing to unknown mcast groups
  genetlink: document parallel_ops
  net: rps: fix cpu unplug
  net: davinci_emac: Add support for emac on dm816x
  net: davinci_emac: Fix ioremap for devices with MDIO within the EMAC address space
  net: davinci_emac: Fix incomplete code for getting the phy from device tree
  net: davinci_emac: Free clock after checking the frequency
  net: davinci_emac: Fix runtime pm calls for davinci_emac
  net: davinci_emac: Fix hangs with interrupts
  ip: zero sockaddr returned on error queue
  ...

Pull crypto fix from Herbert Xu:
 "This fixes a regression that arose from the change to add a crypto
  prefix to module names which was done to prevent the loading of
  arbitrary modules through the Crypto API.

  In particular, a number of modules were missing the crypto prefix
  which meant that they could no longer be autoloaded"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: add missing crypto module aliases

"sp->desc[i]" has 25 characters.  "dev->name" has 15 characters.  If we
used all 15 characters then the sprintf() would overflow.

I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as
well, even though it can't overflow just to be consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: couldn't read OCP_SRAM_DATA

Read OCP_SRAM_DATA would read additional bytes and may let
the hw abnormal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hauke Mehrtens says:

====================
bgmac: some fixes to napi usage

I compared the napi documentation with the bgmac driver and found some
problems in that driver. These two patches should fix the problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
sh_eth fixes

I'm currently looking at Ethernet support on the R-Car H2 chip,
reviewing and testing the sh_eth driver.  Here are fixes for two fairly
obvious bugs in the driver; I will probably have some more later.

These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver connects and disconnects the PHY device whenever the
net device is brought up and down.  The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.

I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.

As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
  not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table).  However we do need
to turn the PRM (promiscuous) flag on and off for other chips.

- Remove the unlikely() from the TSU functions that we may safely
  call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
  it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
  would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduce the attack vector and stop generating IPv6 Fragment Header for
paths with an MTU smaller than the minimum required IPv6 MTU
size (1280 byte) - called atomic fragments.

See IETF I-D "Deprecating the Generation of IPv6 Atomic Fragments" [1]
for more information and how this "feature" can be misused.

[1] https://tools.ietf.org/html/draft-ietf-6man-deprecate-atomfrag-generation-00Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reference my pinctrl GIT tree @kernel.org
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Timur reports that this code crashes if nfunctions is 0. Fix the
loop iteration to only consider valid elements of the functions
array.
Reported-by: Timur Tabi <timur@codeaurora.org>
Cc: Pramod Gurav <pramod.gurav@smartplayin.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Andy Gross <agross@codeaurora.org>
Fixes: 32745581 "pinctrl: qcom: Add support for reset for apq8064"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull GPIO fixes from Linus Walleij:
 "Here is a set of fixes that mainly appeared when Johan Hovold started
  exercising the removal path of the GPIO library, dealing with
  hotplugging of GPIO controllers. Details from tag:

  A slew of fixes dealing with some irritating bugs (non-regressions)
  that have been around forever in the GPIO subsystem, most of them also
  tagged for stable:

   - A large slew of fixes from Johan Hovold who is finally testing and
     reviewing the removal path of the GPIO drivers.

   - Fix of_get_named_gpiod_flags() so it works as expected.

   - Fix an IRQ handling bug in the crystalcove driver"

* tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpiolib: of: Correct error handling in of_get_named_gpiod_flags
  gpio: sysfs: fix gpio attribute-creation race
  gpio: sysfs: fix gpio device-attribute leak
  gpio: sysfs: fix gpio-chip device-attribute leak
  gpio: unregister gpiochip device before removing it
  gpio: fix sleep-while-atomic in gpiochip_remove
  gpio: fix memory leak and sleep-while-atomic
  gpio: clean up gpiochip_add error handling
  gpio: fix gpio-chip list corruption
  gpio: fix memory and reference leaks in gpiochip_add error path
  gpio: crystalcove: use handle_nested_irq