Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We need to check only if the WM8350 is master and only when starting
the stream so if either is not true then we can skip the check.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This adds a new control named 'Master Playback Switch' for cs4270
codecs. It is implemented using the new SOC_DOUBLE_EXT macro to catch
the put function and store the information about manually set mute
controls from userspace. When a manual mute is set, we don't want the
soc core to un-mute the outputs.

Renamed cs4270_mute() to cs4270_dai_mute() to avoid confusion.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The control modifies the MUTE register, hence the polarity must be
inverted.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make sure we get the DAI operations initialised.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Say what invalid values we're seeing when we see an invalid value and
ensure that errors are displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

It's expected behaviour for the CODEC header to provide them but the
WM8350 doesn't due to having all the registers together under drivers/mfd.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There is only one LRCLK pin on each interface.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The S3C64xx IIS code had a number of problems with device registration.
The hardware has two IIS ports of which the driver supported only one
at once via a single exported DAI, attempting to identify the DAI to
use based on the dev->id of the ASoC platform device.  As well as
limiting the driver to only supporting one IIS port at once this also
meant that the ID of the soc-audio device (or in future the card device)
had to match the IIS ID.

Fix both problems by converting the driver to register the DAIs based on
probing of platform devices registered by the arch/arm code, using those
platform devices to interact with the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add a macro for double controls with special callback functions.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for the four channel TDM mode
on Beagle board.

Depending on the channel count, the interface needs to be
configured differently (I2S for stereo DSP_A for four channels)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Support for 4 channel TDM (SND_SOC_DAIFMT_DSP_A) for twl4030
codec.
The channel allocations are:
Playback:
TDM         i2s   TWL RX
Channel 1   Left  SDRL2
Channel 3   Right SDRR2
Channel 2   --    SDRL1
Channel 4   --    SDRR1

Capture:
TDM         i2s   TWL TX
Channel 1   Left  TXL1
Channel 3   Right TXR1
Channel 2   --    TXL2
Channel 4   --    TXR2
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

It relies on EXPORT_SYMBOL_GPL() symbols.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The original idea came from pHilipp, and this makes the code looks
more consistent.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The SSP DMA parameters can actually be easily generated at run-time since
they are almost similar except for the FIFO width and direction. Another
benefit is the re-use of information from 'struct ssp_device', like SSDR
physical FIFO address and DRCMR register index for both directions.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: pHilipp Zabel <philipp.zabel@gmail.com>

Add DAPMs for VDL(Voice Down Link) path. To support VDL path, we have
to change DAPMs of outputs(Earpiece, PreDrive Left/Right, Headset
Left/Right, Carkit Left/Right) from mux to mixer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is now handled by symmetric_rates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Save a little extra power by enabling the DC servo offset correction
for the output channels only when the relevant channels are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Modify the default startup sequence in the chip to set the DC servo
dither level for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

CLK_DSP provides a master clock for the DAC and ADC related functionality
on the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.

Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.

Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add checking in hw_params and prepare to detect bufferless pcms(i.e. BT
<--> codec).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The driver is out of sync with the core functions it is using.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This will form a basis for further power check refactoring: the overall
goal of these changes is to allow us to check power separately to
applying it, allowing improvements in the power sequencing algorithms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add Voice DAI to support the PCM voice interface of the twl4030 codec.

The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.

The PCM voice interface has two modes
 - PCM mode1 : This uses the normal FS polarity and the rising edge of
               the clock signal.
 - PCM mode2 : This uses the FS polarity inverted and the falling edge
               of the clock signal.

If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>