The message buffer RAM area is not a contiguous 1KB area but 2 partitions
of 512 bytes each. Till now, we used Message buffers with payload size 8
bytes, which translates to 32 MBs per partition and no spare space is left
in any partition.
However, in upcoming SOC LX2160A the message buffers can have payload size
64 bytes. This results in less than 32 MBs per partition and some empty
area is left at the end of each partition.This empty area should not be
accessed.
Therefore, split the Message Buffer RAM area into two partitions.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Till now the flexcan module supported 8 byte payload size as per CAN 2.0
specifications. But now upcoming flexcan module in NXP LX2160A SOC
supports CAN FD protocol too. The Message buffers need to be configured
to have payload size 64 bytes.

Therefore, added provision in the driver for payload size to be 64 bytes.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

rx offload depends on number of message buffers, which in turn depends
on messgae buffer size. with the upcoming LX2160A SOC the message buffer
size can be configured to 72 bytes if it were to be used in CAN FD mode.

The current mode in which the flexcan is being operated is known at the
time of flexcan_open() but not at the time of flexcan_probe().

Therefore, move the rx_offload_add() from flexcan_probe() to
flexcan_open(). correspondingly, move rx_offload_delete() from
flexcan_remove() to flexcan_close().
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Self reception disable bit needs to be cleared for loopback mode to work
in flexcan.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If wakeup is enabled, enter stop mode, else enter disabled mode. Self wake
can only work on stop mode.

Starting from IMX6, the flexcan stop mode control bits is SoC specific,
move it out of IP driver and parse it from devicetree.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The FlexCAN controller can parse the stop mode property to enable CAN
self wakeup feature.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

With the conversion of the flexcan driver to support both timestamp and
FIFO mode the setup of the MCR register ("enable fifo") has been moved.

This patch moves the comment too, in order to match the code again.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the following checkpatch warning:

| Macro argument 'x' may be better as '(x)' to avoid precedence issues

Fixes: cbffaf7a ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The patch fixes the indention by replacing space by tabs, as noted by
checkpatch:

| ERROR: code indent should use tabs where possible
| #980: FILE: drivers/net/can/flexcan.c:980:

Fixes: da49a807 ("can: flexcan: implement error passive state quirk")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the indentio nin flexcan_start_xmit() by alligning the
code to the opening parenthesis.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

flexcan is an IP module independent of the SOC architecture.
Therefore, enable it for all architectures.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds SPDX-License-Identifier to Kconfig and Makefile.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds support for ASEM opto-isolated dual channels
CAN raw device (http://www.asem.it)
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add support for can 2.0.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add compatible string and new attributes to support the Xilinx CAN
FD 2.0.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Trivial fix to spelling mistake in netdev_dbg error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Randy reported when CONFIG_PROC_FS is not enabled:
    ld: net/ipv4/af_inet.o: in function `inet_init':
    af_inet.c:(.init.text+0x42d): undefined reference to `raw_init'

Fix by moving the endif up to the end of the proc entries

Fixes: 6897445f ("net: provide a sysctl raw_l3mdev_accept for raw socket lookup with VRFs")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
bnx2x: Popoulate firmware versions in driver info query.

The patch series populates MBI and storm firware versions in the ethtool
driver info query.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch populates the Storm FW version in the ethtool driver query data.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch populates the MBI version in the ethtool driver query data.
Adding 'extended_dev_info_shared_cfg' structure describing the nvram
structure, this is required to access the mbi version string.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only one caller needs to pull TCP headers, so lets
move __skb_pull() to the caller side.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds OEM Mellanox commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.

ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for
getting mac address.
ncsi_rsp_handler_oem_mlx: This handles response received for all
mellanox OEM commands.
ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and
set it to device.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

writex() has implicit barriers, that's what makes it different from
writex_relaxed(). Therefore these calls to mmiowb() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Port 0/1 of HiP08 supports 10G and 25G. This patch adds a
change to configure NIC port speed same as that of  optical
module(SFP/QFSP). Driver gets the optical module speed and
sets NIC port speed accordingly.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nicolas Dichtel says:

====================
Ease to interpret net-nsid

The goal of this series is to ease the interpretation of nsid received in
netlink messages from other netns (when the user uses
NETLINK_F_LISTEN_ALL_NSID).

After this series, with a patched iproute2:

$ ip netns add foo
$ ip netns add bar
$ touch /var/run/netns/init_net
$ mount --bind /proc/1/ns/net /var/run/netns/init_net
$ ip netns set init_net 11
$ ip netns set foo 12
$ ip netns set bar 13
$ ip netns
init_net (id: 11)
bar (id: 13)
foo (id: 12)
$ ip -n foo netns set init_net 21
$ ip -n foo netns set foo 22
$ ip -n foo netns set bar 23
$ ip -n foo netns
init_net (id: 21)
bar (id: 23)
foo (id: 22)
$ ip -n bar netns set init_net 31
$ ip -n bar netns set foo 32
$ ip -n bar netns set bar 33
$ ip -n bar netns
init_net (id: 31)
bar (id: 33)
foo (id: 32)
$ ip netns list-id target-nsid 12
nsid 21 current-nsid 11 (iproute2 netns name: init_net)
nsid 22 current-nsid 12 (iproute2 netns name: foo)
nsid 23 current-nsid 13 (iproute2 netns name: bar)
$ ip -n bar netns list-id target-nsid 32 nsid 31
nsid 21 current-nsid 31 (iproute2 netns name: init_net)

v3 -> v4:
  - patch 5/5: fix imbalance lock in error path

v2 -> v3:
  - patch 5/5: account NETNSA_CURRENT_NSID in rtnl_net_get_size()

v1 -> v2:
  - patch 1/5: remove net from struct rtnl_net_dump_cb
  - patch 2/5: new in this version
  - patch 3/5: use a bool to know if rtnl_get_net_ns_capable() was called
  - patch 5/5: use struct net_fill_args
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Like the previous patch, the goal is to ease to convert nsids from one
netns to another netns.
A new attribute (NETNSA_CURRENT_NSID) is added to the kernel answer when
NETNSA_TARGET_NSID is provided, thus the user can easily convert nsids.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Combined with NETNSA_TARGET_NSID, it enables to "translate" a nsid from one
netns to a nsid of another netns.
This is useful when using NETLINK_F_LISTEN_ALL_NSID because it helps the
user to interpret a nsid received from an other netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like it was done for link and address, add the ability to perform get/dump
in another netns by specifying a target nsid attribute.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a preparatory work. To avoid having to much arguments for the
function rtnl_net_fill(), a new structure is defined.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This argument is not used anymore.

Fixes: cab3c8ec ("netns: always provide the id to rtnl_net_fill()")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed* enhancements series

The patch series add few enhancements to qed/qede drivers.

Changes from previous versions:
-------------------------------
v3: Revert v2 changes as the other paths (i.e. ptp) access the same data in
    atomic context.
v2: Use __set_bit()/__clear_bit() where data access doesn't need to be
    atomic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds driver support for MBI image update through MFW.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of internal reload (e.g., mtu change), there could be a race
between link-up notification from mfw and the driver unload processing. In
such case kernel assumes the link is up and starts using the queues which
leads to the server crash.

Send link notification to the kernel only when driver has already requested
MFW for the link.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The values represented by qede->flags is being used in mixed ways:
  1. As 'value' at some places e.g., QEDE_FLAGS_IS_VF usage
  2. As bit-mask(value) at some places e.g., QEDE_FLAGS_PTP_TX_IN_PRORGESS
     usage.
This implementation pose problems in future when we want to add more flag
values e.g., overlap of the values, overflow of 64-bit storage.

Updated the implementation to go with approach (2) for qede->flags.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MFW sends UFP notifications mostly during the device init phase and PFs
might not be assigned with a name by this time. Hence capturing port-id in
the debug messages would help in finding which PF the ufp notification was
sent to.

Also, fixed a minor scemantic issue in a debug print.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
Add support for Aquantia AQtion USB to 5/2.5GbE devices

This patchset introduces support for new multigig ethernet to USB dongle,
developed jointly by Aquantia (Phy) and ASIX (USB MAC).

The driver has similar structure with other ASIX MAC drivers (AX88179), but
with a number of important differences:
- Driver supports both direct Phy and custom firmware interface for Phy
  programming. This is due to different firmware modules available with
  this product.
- Driver handles new 2.5G/5G link speed configuration and reporting.
- Device support all speeds from 100M up to 5G.
- Device supports MTU up to 16K.

Device supports various standard networking features, like
checksum offloads, vlan tagging/filtering, TSO.

The code of this driver is based on original ASIX sources and was extended
by Aquantia for 5G multigig support.

Patchset v2 includes following changes:
- Function variables declarions fixed to reverse xmass tree
- Improve patch layout structure
- Remove unnecessary curly braces in switch/case statements
- Use 'packed' attribute for HW structures only
- Use eth_mac_addr function in set_mac_addr callback
- Remove unnecessary 'memset' calls.
- Read MAC address from EEPROM function has now better name
- Use driver_priv field to store context. It avoids ugly cast.
- Set max_mtu field. Remove check for MTU size
- Rewrite read/write functions. Add helpers for read/write 16/32 bit values
- Use mask and shifts instead of bitfields to support BE platforms.
- Use stack allocated buffer for configuring mcast filters
- Use AUTONEG_ENABLE when go to suspend state
- Pad out wol_cfg field from context structure. Use stack allocated instead
- Remove driver version
- Check field 'duplex' in set_link_ksetting callback as well
- Use already created defines in usb matching macro
- Rename phy_ops struct to phy_cfg
- Use ether_addr_copy for copying mac address
- Add fall-through comment in switch/case for avoid checkpatch warning
- Remove match for CDC ether device
- Add ASIX's HW id-s to match this driver
- Add all HW id-s with which driver can work to blacklist of cdc_ether driver

Patchset v3 includes following changes:
- Use linkmode_copy instead of bitmap_copy
- Remove Direct PHY access code since production HW will not have this
    mode anymore
- Fix line over 80 symbols and alignments in cdc_ether patch
- Add match for ECM configuration
    On start our HW reports both ECM and vendor configs.
    Linux prefers to use ECM driver and chooses active configuration
    which is for ecm driver (not for vendor specific).
    We need to match this configuration and forcibly switch configuration
    to vendor specific.

Patchset v4 includes following changes:
- Set gso_max_size.
- Optimize accessing to descriptors
- Use SKB_TRUESIZE macro.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added Aquantia and ASIX device IDs to prevent loading cdc_ether for
these devices. Our firmware reports CDC configuration simultaneously
with vendor specific.
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It enables driver for ASIX products which are also based on
aqc111/112U chips.
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>