Now that the Blackfin machine drivers have been updated to the
multicomponent support, update the resources to match.  The pin
settings are now a board issue and removed from the driver.
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Anomaly 05000480 on BF537 rev 0.0, 0.1, 0.2:
Multiple Simultaneous Urgent DMA Requests May Cause DMA System Instability

Suggested Workaround:
Program the DMA Traffic Control Period to a non-zero value.  This forces
the DMA block to group accesses together rather than allow arbitration for
each piece of data placed on the internal DMA bus.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the bfin_write() func needs proper type information in order to
expand into the right bfin_writeX() variant, preserve the addr's type
when setting up the local __addr.  Otherwise the helpers will detect
the variant based upon sizeof(void) which is almost never right.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

->read_proc interface is going away, switch to seq_file.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

->read_proc interface is going away, switch to seq_file.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Use tabs instead of spaces to indent.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

old cpu_xxx() APIs is planned to removed later. then, converted.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Every callter (except kthread_bind) should use proper
set_cpus_allowed_ptr() APIs.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

We plan to remove cpu_possible_map and cpu_present_map later and we
have proper init_cpu_possible() and init_cpu_present() APIs.

Therefore this patch rewrites platform_init_cpus and platform_prepare_cpus
by their APIs.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Both the BF548-EZKIT and the BF561-EZKIT use top boot flashes, so now
that Das U-Boot uses the last small sector for its environment, update
their nor layout in the kernel accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Turns out the documentation is wrong and doing "RAISE 1" does not result
in a software reset, only a core reset.  So when the on-chip rom has a
functioning reset helper, use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These boards don't have AD1980 modules, and that device is deprecated,
so don't bother building it up by default anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the value of these MMRs aren't changing, store the value in a local
variable and work off of that.  This avoids multiple MMR reads which are
implicitly forced by the volatile markings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The BF537 SIC combines the gpio port H mask A interrupts with the
emac rx interrupt, so we need to demux this in software.

It also combines the gpio port H mask B and the emac tx interrupts,
and the watchdog and port F mask B interrupts, but since we don't
support mask B yet, just add the defines for now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The search logic in the gpio demux walks all possible gpio blocks starting
at the specified pin.  The trouble on bf537 parts when we demux the port
F and port G mask A interrupts is that we also demux port H mask A ints.
Most of the time this isn't an issue as people don't usually use port H,
but might as well avoid it when possible.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This functionality was merged into the common bfin_pm_standby_ctrl func
some time ago, so punt these now unused funcs and data, and localize the
wake funcs that aren't needed externally anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The SIC interrupt line muxing that the bf537 does is specific to this
CPU (thankfully), so rip it out of the common code and move it to a
bf537-specific file.  This tidies up the common code significantly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These are only used in a few internal Blackfin places, so move the irq
prototypes out of the global header and into the internal irq one.  No
functional changes other than shuffling locales.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Prefer MMR named checks over part-specific lists, condense duplicated
code across different #ifdef branches, simplify CONFIG_PM ifdefs, and
drop unused kgdb header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These are in linux/ptrace.h, so no need for us to duplicate them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Make sure we mark cache flushing as unsafe to kgdb in SMP mode so that
kgdb doesn't flush things incorrectly on us.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Not sure when we stopped using this field, but nothing in the tree uses
this now, so punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

After some cache setup reordering changesets, the blackfin_cpudata init
was left behind.  While cpu0's data was correct, cpu1's data was not.
Not that big of a deal as these are only used in the cpuinfo output, but
should still be fixed.  So move the setup of these fields to the common
cache setup function to avoid this happening again in the future.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The smp flush lines are too long and have too many newlines, so scale
them back to match the other lines.

The %p modifier shows "(null)" for 0, so use %08x instead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Build the sound pieces that the board actually has into the kernel, and
punt older devices that we discourage.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This brings the parts in line with newer ones, and makes things easier
to read at a glance.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These files had a lot of whitespace damage, mostly due to copying and
pasting original files that had damage.

The BF561 header also had a lot of unused CONFIG_DEF_xxx defines, so
punt them all.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Start a new common IRQ header and move all of the CEC pieces there.  This
lets the individual part headers worry just about its SIC defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Seems the ipipe code just copied & pasted the existing irq lookup logic,
so pull the logic out of do_irq() and into a local helper, and convert
the two users over to that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The local ivg structs need not be exported, so mark them as static.
Further, the "num_spurious" variable is only incremented and never
actually read anywhere, so punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the on-chip L1 regions are not cacheable, there is no point in
trying to flush/invalidate them.  Plus, older Blackfin parts like to
trigger an exception (like BF533-0.3).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

* 'for-linus/2640/i2c' of git://git.fluff.org/bjdooks/linux: (21 commits)
  mach-ux500: set proper I2C platform data from MOP500s
  i2c-nomadik: break out single messsage transmission
  i2c-nomadik: reset the hw after status check
  i2c-nomadik: remove the unnecessary delay
  i2c-nomadik: change the TX and RX threshold
  i2c-nomadik: add code to retry on timeout failure
  i2c-nomadik: use pm_runtime API
  i2c-nomadik: print abort cause only on abort tag
  i2c-nomadik: correct adapter timeout initialization
  i2c-nomadik: remove the redundant error message
  i2c-nomadik: corrrect returned error numbers
  i2c-nomadik: fix speed enumerator
  i2c-nomadik: make i2c timeout specific per i2c bus
  i2c-nomadik: add regulator support
  i2c: i2c-sh_mobile bus speed platform data V2
  i2c: i2c-sh_mobile clock string removal
  i2c-eg20t: Support new device ML7223 IOH
  i2c: tegra: Add de-bounce cycles.
  i2c: tegra: fix repeated start handling
  i2c: tegra: recover from spurious interrupt storm
  ...

Merge branches 'for-2639/i2c-eg20t', 'for-2639/i2c-shmobile', 'for-2639/i2c-tegra' and 'for-2639/i2c-nomadik2' into for-linus/2640/i2c

This specifies the new per-platform timeout per I2C bus and
switches the I2C buses to fast mode, and increase the FIFO
depth to 8 for reads and writes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Reduce code size in the message transfer function by factoring out
a single-message transfer function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

In case of I2C timeout, reset the HW only after the HW status
is read, otherwise the staus will be lost.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>