Use dev_info to log link up/down messages.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The out of tree driver and the in kernel driver should use the same
interrupt handling logic for mailbox interrupts.  The difference in
the handlers was causing dissimilar behavior between the two drivers
complicating debug and trouble shooting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map.  To do this I have expanded the work done in the main loop by
pushing first into tx_buffer.  This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor.  The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo.  By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.

To do this I also needed to change the logic and/or drop some flags.  I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do.  Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb.  Instead we can just check the bitflag in the skb.

In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway.  Instead of doing that we can just
use context 0 for all descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads.  Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

IEEE DCBx has a mechanism to change the default user priority. In
the normal case the OS can handle this via cgroups, iptables, socket,
options etc.

With SR-IOV and direct assigned VF devices the default priority
needs to be set by the PF device so the inserted VLAN tag is
correct.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is already checked by the caller (tunnel64_rcv) and brings ipip6_rcv
in line with ipip_rcv.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check message length before accessing "target" field,
as we do for other types.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because of rt->n removal, we do not need neigh argument any more.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are copying data into 16 char arrays.  They all specify that the
first string can't be more than 11 characters but once you add on the
"-rx-" and the NUL character there isn't space for the %d.

The first string is probably never going to be 11 characters, but if it
is then let's truncate the string instead of corrupting memory.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ioremap returns 'void __iomem *' type.

Fix the following build warnings:

drivers/net/ethernet/smsc/smc911x.c:2079:14: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2079:14:    expected unsigned int *addr
drivers/net/ethernet/smsc/smc911x.c:2079:14:    got void [noderef] <asn:2>*
drivers/net/ethernet/smsc/smc911x.c:2086:18: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2086:18:    expected void [noderef] <asn:2>*base
drivers/net/ethernet/smsc/smc911x.c:2086:18:    got unsigned int *addr
drivers/net/ethernet/smsc/smc911x.c:2091:25: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/smsc/smc911x.c:2091:25:    expected void volatile [noderef] <asn:2>*addr
drivers/net/ethernet/smsc/smc911x.c:2091:25:    got unsigned int *addr
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In two places, tmp is initialized implicitly by being passed as a
pointer during a function call.  However, this is not obvious to the
compiler, which logs a warning.
Signed-off-by: Simon Que <sque@chromium.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

When there is heavy transmission traffic in the CPDMA, then Rx descriptors
memory is also utilized as tx desc memory looses all rx descriptors and the
driver stops working then.

This patch adds boundary for tx and rx descriptors in bd ram dividing the
descriptor memory to ensure that during heavy transmission tx doesn't use
rx descriptors.

This patch is already applied to davinci_emac driver, since CPSW and
davici_dmac shares the same CPDMA, moving the boundry seperation from
Davinci EMAC driver to CPDMA driver which was done in the following
commit

commit 86d8c07f
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date:   Tue Jan 3 05:27:47 2012 +0000

    net/davinci: do not use all descriptors for tx packets

    The driver uses a shared pool for both rx and tx descriptors.
    During open it queues fixed number of 128 descriptors for receive
    packets. For each received packet it tries to queue another
    descriptor. If this fails the descriptor is lost for rx.
    The driver has no limitation on tx descriptors to use, so it
    can happen during a nmap / ping -f attack that the driver
    allocates all descriptors for tx and looses all rx descriptors.
    The driver stops working then.
    To fix this limit the number of tx descriptors used to half of
    the descriptors available, the rx path uses the other half.

    Tested on a custom board using nmap / ping -f to the board from
    two different hosts.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle the reception of uncompressed packets (dispatch type = IPv6).
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor the handing of the skb's to the individual lowpan devices into a
function.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The limition of imx6 internal bus cause fec can't achieve 1G perfomance.
There will be many packages lost because FIFO over run.

This patch enable pause frame flow control.

Before this patch
iperf -s -i 1
TCP window size: 85.3 KByte (default)
------------------------------------------------------------
[  4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49773
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0- 1.0 sec  6.35 MBytes  53.3 Mbits/sec
[  4]  1.0- 2.0 sec  3.39 MBytes  28.5 Mbits/sec
[  4]  2.0- 3.0 sec  2.63 MBytes  22.1 Mbits/sec
[  4]  3.0- 4.0 sec  1.10 MBytes  9.23 Mbits/sec

ifconfig
   RX packets:46195 errors:1859 dropped:1 overruns:1859 frame:1859

After this patch
iperf -s -i 1

[  4] local 10.192.242.153 port 5001 connected with 10.192.242.94 port 49757
[ ID] Interval       Transfer     Bandwidth
[  4]  0.0- 1.0 sec  49.8 MBytes   418 Mbits/sec
[  4]  1.0- 2.0 sec  50.1 MBytes   420 Mbits/sec
[  4]  2.0- 3.0 sec  47.5 MBytes   399 Mbits/sec
[  4]  3.0- 4.0 sec  45.9 MBytes   385 Mbits/sec
[  4]  4.0- 5.0 sec  44.8 MBytes   376 Mbits/sec

ifconfig
   RX packets:2348454 errors:0 dropped:16 overruns:0 frame:0
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ASIX AX88772B started to pack data even more tightly. Packets and the ASIX packet
header may now cross URB boundaries. To handle this we have to introduce
some state between individual calls to asix_rx_fixup().
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device comes up with a MAC address of all zeros. We need to read the
initial device MAC from EEPROM so it can be set properly later.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to e1000e and igb.  Most notably is the
added timestamp support in e1000e and additional software timestamp
support in igb.  As well as, the added thermal data support and SR-IOV
configuration support in igb.

v2- dropped the following patches from the previous 14 patch series
because changes were requested from the community:
  e1000e: add support for IEEE-1588 PTP
  igb: Report L4 Rx hash via skb->l4_rxhash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than use an extra #define for something that already exists, use the
kernel #define for the PTP port.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

To prevent a race condition where an skb has been saved to return the Tx
timestamp later and the driver is removed, add a check to determine if we
have an skb stored and, if so, free it.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a check against possible Rx timestamp freezing in the hardware via
watchdog mechanism. This situation can occur when an Rx timestamp has been
latched, but the packet has been dropped because the Rx ring is full.

Whenever a packet comes in that should be timestamped, the Rx timestamp
gets latched into the hardware registers and we will store the jiffy value
in the rx_ring. The watchdog will keep track of his own jiffy timer
whenever there is no valid timestamp in the registers.

If the watchdog detects a valid timestamp in the registers, meaning that no
Rx packet has consumed it yet, it will check which time is most recent: the
last time in the watchdog or any time in the rx_rings. If the most recent
"event" was more than 5 seconds ago, it will flush the Rx timestamp and
print a warning message to the syslog.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When transmitting a packet that must return a Tx timestamp, a work item
gets scheduled to poll for the Tx timestamp being completed in hardware.
Add a timeout on this work item of 15 seconds from when the driver gets the
skb, after which it will stop polling. Report via stats and system log if
this occurs.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable SW timestamping for situations where the user may prefer it over HW
timestamping or there may not be HW timestamping.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of our adapters have internal sensors that report thermal data.  This
patch enables reporting of that data via sysfs.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of our devices have internal sensors for reporting thermal data.
This patch creates the interface to the sensors for exporting via sysfs.
Subsequent patch will actually export the data.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of our adapters have sensors on them accessible via i2c and a private
interface.  This patch implements the kernel interface for i2c to those sensors.
Subsequent patches will provide functions to export that data.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set.  Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the standard #defines for PCIe Capability ASPM fields.

Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits.  PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: e1000-devel@lists.sourceforge.net
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If neigh is not found, create new one.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For RTF_GATEWAY route, return rt->rt6i_gateway.
Otherwise, return 2nd argument (destination address).

This will be used by following patches which remove rt->n
dependency patches in ip6_dst_lookup_tail() and ip6_finish_output2().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function, which looks up neighbour entry for an IPv6 address
without touching refcnt, will be used for patches to remove
dependency on rt->n (neighbour entry in rt6_info).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>