Current API between qed and protocol modules allows passing an
additional private string - but it doesn't get utilized by qed
anywhere.

Clarify the API by removing it and renaming it 'set_name'.

CC: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace meaningless logged print ('Ending successfully qede probe')
with a single-liner containing interesting information about probed
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass additional information about package installed on persistent memory
so that protocol drivers would be able to log it.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we're closing the parser searching for RDMA when stoping the
fastpath, we need to re-enable it when starting the fastpath once again.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Today, driver has a synchronization point while closing
the device which synchronizes its slowpath interrupt line.
However, that's insufficient as that ISR would schedule the
slowpath-tasklet - so even after ISR is over it's possible the
handling of the interrupt has not completed.

By doing a disable/enable on the taskelt we guarantee that all
HW events that should no longer be genereated from that point
onward in the flow are truly behind us.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A0 never went public, so no need to protect against it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The parameter reflects the number of physical ports connected to a single
engine, not all.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case nvram layout of board is incorrect, board may exhibit peculiar
oddities. Log such a rare event.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flows configuring tunnel ports in HW use the main_ptt which should
be reserved for core-functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Solves the following warning in qede -
 - Several cases of missing cpu_to_le16() conversions
 - Adds 'static' to one function declaration
 - Removes dcbnl operation that's currently getting populated twice
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This field is sizeof of corresponding kmem_cache so it can't be negative.

Space will be saved after 32-bit kmem_cache_create() patch.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This field is sizeof of corresponding kmem_cache so it can't be negative.

Prepare for 32-bit kmem_cache_create().
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of busy poll, napi_complete_done returns false and does not
dequeue napi. In this case do not unmask the intr. We are guaranteed
napi is called again. This reduces unnecessary iowrites.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user instructs to remove all filters from chain, we cannot destroy
the chain as other actions may hold a reference. Also the put in errout
would try to destroy it again. So instead, just walk the chain and remove
all existing filters.

Fixes: 5bc17018 ("net: sched: introduce multichain support for filters")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

*p_filter_chain is rcu-dereferenced on reader path. So here in writer,
property assign the pointer.

Fixes: 2190d1d0 ("net: sched: introduce helpers to work with filter chains")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull pstore fix from Kees Cook:
 "Marta noticed another misbehavior in EFI pstore, which this fixes.

  Hopefully this is the last of the v4.12 fixes for pstore!"

* tag 'pstore-v4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  efi-pstore: Fix write/erase id tracking

Pull ACPI fixes from Rafael Wysocki:
 "These revert a 4.11 change that turned out to be problematic and add a
  .gitignore file.

  Specifics:

   - Revert a 4.11 commit related to the ACPI-based handling of laptop
     lids that made changes incompatible with existing user space stacks
     and broke things there (Lv Zheng).

   - Add .gitignore to the ACPI tools directory (Prarit Bhargava)"

* tag 'acpi-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPI / button: Remove lid_init_state=method mode"
  tools/power/acpi: Add .gitignore file

Pull power management fixes from Rafael Wysocki:
 "These fix RTC wakeup from suspend-to-idle broken recently, fix CPU
  idleness detection condition in the schedutil cpufreq governor, fix a
  cpufreq driver build failure, fix an error code path in the power
  capping framework, clean up the hibernate core and update the
  intel_pstate documentation.

  Specifics:

   - Fix RTC wakeup from suspend-to-idle broken by the recent rework of
     ACPI wakeup handling (Rafael Wysocki).

   - Update intel_pstate driver documentation to reflect the current
     code and explain how it works in more detail (Rafael Wysocki).

   - Fix an issue related to CPU idleness detection on systems with
     shared cpufreq policies in the schedutil governor (Juri Lelli).

   - Fix a possible build issue in the dbx500 cpufreq driver (Arnd
     Bergmann).

   - Fix a function in the power capping framework core to return an
     error code instead of 0 when there's an error (Dan Carpenter).

   - Clean up variable definition in the hibernation core (Pushkar
     Jambhlekar)"

* tag 'pm-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: dbx500: add a Kconfig symbol
  PM / hibernate: Declare variables as static
  PowerCap: Fix an error code in powercap_register_zone()
  RTC: rtc-cmos: Fix wakeup from suspend-to-idle
  PM / wakeup: Fix up wakeup_source_report_event()
  cpufreq: intel_pstate: Document the current behavior and user interface
  cpufreq: schedutil: use now as reference when aggregating shared policy requests

We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Fixes: 9d640843 ("i2c: designware: don't infer timings described by ACPI from clock rate")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Prior to the pstore interface refactoring, the "id" generated during
a backend pstore_write() was only retained by the internal pstore
inode tracking list. Additionally the "part" was ignored, so EFI
would encode this in the id. This corrects the misunderstandings
and correctly sets "id" during pstore_write(), and uses "part"
directly during pstore_erase().
Reported-by: Marta Lofstedt <marta.lofstedt@intel.com>
Fixes: 76cc9580 ("pstore: Replace arguments for write() API")
Fixes: a61072aa ("pstore: Replace arguments for erase() API")
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Marta Lofstedt <marta.lofstedt@intel.com>

Vivien Didelot says:

====================
net: dsa: distribute switch events

DSA is by nature the support for a switch fabric, which can be composed
of a single, or multiple interconnected Ethernet switch chips.

The current DSA core behavior is to identify the slave port targeted by
a request (e.g. adding a VLAN entry), and program the switch chip to
which it belongs accordingly.

This is problematic in a multi-chip environment, since all chips of a
fabric must be aware of most configuration changes. Here are some
concrete examples in a 3-chip environment:

         [CPU].................... (mdio)
    (eth0) |   :       :          :
          _|_____    _______    _______
         [__sw0__]--[__sw1__]--[__sw2__]
          |  |  |    |  |  |    |  |  |
          v  v  v    v  v  v    v  v  v
          p1 p2 p3   p4 p5 p6   p7 p8 p9

If you add a VLAN entry on p7, sw2 gets programmed, but frames won't
reach the CPU interface in a VLAN filtered setup. sw0 and sw1 also need
to be programmed. The same problem comes with MAC addresses (FDB, MDB),
or ageing time changes for instance.

This patch series uses the notification chain introduced for bridging,
to notify not only bridge, but switchdev attributes and objects events
to all switch chips of the fabric.

An ugly debug message printing the ignored event and switch info in the
code handling the switch VLAN events would give us:

    # bridge vlan add dev p7 vid 42
    sw0: ignoring DSA_NOTIFIER_VLAN_ADD for sw2 (prepare phase)
    sw1: ignoring DSA_NOTIFIER_VLAN_ADD for sw2 (prepare phase)
    sw0: ignoring DSA_NOTIFIER_VLAN_ADD for sw2 (commit phase)
    sw1: ignoring DSA_NOTIFIER_VLAN_ADD for sw2 (commit phase)

To achieve that, patches 1-8 change the scope of the bridge and
switchdev callbacks from the DSA slave device to the generic DSA port,
so that the port-wide API can be used later for switch ports not exposed
to userspace, such as CPU and DSA links.

Patches 9-15 move the DSA port specific functions in a new port.c file.

Patches 16-20 introduce new events to notify the fabric about switchdev
attributes and objects manipulation.

This patch series only adds the plumbing to support a distributed
configuration, but for the moment, each switch chip ignores events from
other chips of the fabric, to keep the current behavior.

The next patch series will add support for cross-chip configuration of
bridge ageing time, VLAN and MAC address databases operations, etc.
====================
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two new DSA_NOTIFIER_VLAN_ADD and DSA_NOTIFIER_VLAN_DEL events to
notify not only a single switch, but all switches of a the fabric when
an VLAN entry is added or removed.

For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two new DSA_NOTIFIER_MDB_ADD and DSA_NOTIFIER_MDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an MDB entry is added or removed.

For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two new DSA_NOTIFIER_FDB_ADD and DSA_NOTIFIER_FDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an FDB entry is added or removed.

For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch keeps the port-wide ageing time handling code in
dsa_port_ageing_time, pushes the requested ageing time value in a new
switch fabric notification, and moves the switch-wide ageing time
handling code in dsa_switch_ageing_time.

This has the effect that now not only the switch that the target port
belongs to can be programmed, but all switches composing the switch
fabric. For the moment, keep the current behavior and ignore other
switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DSA notifier events and info structure definitions are not meant for
DSA drivers and users, but only used internally by the DSA core files.

Move them from the public net/dsa.h file to the private dsa_priv.h file.

Also use this opportunity to turn the events into an anonymous enum,
because we don't care about the values, and this will prevent future
conflicts when adding (and sorting) new events.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the DSA port code which handles VLAN objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the DSA port code which handles MDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the DSA port code which handles FDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the DSA port code which sets a port ageing time in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the DSA port code which sets VLAN filtering on a port in port.c,
where it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the DSA port code which bridges a port in port.c, where it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new port.c file to hold all DSA port-wide logic. This patch moves
in the code which sets a port state.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the scope of the switchdev bridge ageing time attribute setter
from the DSA slave device to the generic DSA port, so that the future
port-wide API can also be used for other port types, such as CPU and DSA
links.

Also ds->ports is now a contiguous array of dsa_port structures, thus
their addresses cannot be NULL. Remove the useless check in
dsa_fastest_ageing_time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the scope of the switchdev VLAN filtering attribute setter from
the DSA slave device to the generic DSA port, so that the future
port-wide API can also be used for other port types, such as CPU and DSA
links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the scope of the switchdev VLAN object handlers from the DSA
slave device to the generic DSA port, so that the future port-wide API
can also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the scope of the switchdev MDB object handlers from the DSA slave
device to the generic DSA port, so that the future port-wide API can
also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the scope of the switchdev FDB object handlers from the DSA slave
device to the generic DSA port, so that the future port-wide API can
also be used for other port types, such as CPU and DSA links.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>