Xin Long says:

====================
sctp: a bunch of fixes for prsctp polices

This patchset is to fix 2 issues for prsctp polices:

  1. patch 1 and 2 fix "netperf-Throughput_Mbps -37.2% regression" issue
     when overloading the CPU.

  2. patch 3 fix "prsctp polices should check both sides' prsctp_capable,
     instead of only local side".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now before using prsctp polices, sctp uses asoc->prsctp_enable to
check if prsctp is enabled. However asoc->prsctp_enable is set only
means local host support prsctp, sctp should not abandon packet if
peer host doesn't enable prsctp.

So this patch is to use asoc->peer.prsctp_capable to check if prsctp
is enabled on both side, instead of asoc->prsctp_enable, as asoc's
peer.prsctp_capable is set only when local and peer both enable prsctp.

Fixes: a6c2f792 ("sctp: implement prsctp TTL policy")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now sctp uses chunk->prsctp_param to save the prsctp param for all the
prsctp polices, we didn't need to introduce prsctp_param to sctp_chunk.
We can just use chunk->sinfo.sinfo_timetolive for RTX and BUF polices,
and reuse msg->expires_at for TTL policy, as the prsctp polices and old
expires policy are mutual exclusive.

This patch is to remove prsctp_param from sctp_chunk, and reuse msg's
expires_at for TTL and chunk's sinfo.sinfo_timetolive for RTX and BUF
polices.

Note that sctp can't use chunk's sinfo.sinfo_timetolive for TTL policy,
as it needs a u64 variables to save the expires_at time.

This one also fixes the "netperf-Throughput_Mbps -37.2% regression"
issue.

Fixes: a6c2f792 ("sctp: implement prsctp TTL policy")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now pahole sctp_chunk, it has 2 memory holes:
   struct sctp_chunk {
	struct list_head           list;
	atomic_t                   refcnt;
	/* XXX 4 bytes hole, try to pack */
	...
	long unsigned int          prsctp_param;
	int                        sent_count;
	/* XXX 4 bytes hole, try to pack */

This patch is to move up sent_count to fill the 1st one and eliminate
the 2nd one.

It's not just another struct compaction, it also fixes the "netperf-
Throughput_Mbps -37.2% regression" issue when overloading the CPU.

Fixes: a6c2f792 ("sctp: implement prsctp TTL policy")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While the driver is probing the adapter, an error may occur before the
netdev structure is allocated and attached to pci_dev. In this case,
not only netdev isn't available, but the tg3 private structure is also
not available as it is just math from the NULL pointer, so dereferences
must be skipped.

The following trace is seen when the error is triggered:

  [1.402247] Unable to handle kernel paging request for data at address 0x00001a99
  [1.402410] Faulting instruction address: 0xc0000000007e33f8
  [1.402450] Oops: Kernel access of bad area, sig: 11 [#1]
  [1.402481] SMP NR_CPUS=2048 NUMA PowerNV
  [1.402513] Modules linked in:
  [1.402545] CPU: 0 PID: 651 Comm: eehd Not tainted 4.4.0-36-generic #55-Ubuntu
  [1.402591] task: c000001fe4e42a20 ti: c000001fe4e88000 task.ti: c000001fe4e88000
  [1.402742] NIP: c0000000007e33f8 LR: c0000000007e3164 CTR: c000000000595ea0
  [1.402787] REGS: c000001fe4e8b790 TRAP: 0300   Not tainted  (4.4.0-36-generic)
  [1.402832] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE>  CR: 28000422  XER: 20000000
  [1.403058] CFAR: c000000000008468 DAR: 0000000000001a99 DSISR: 42000000 SOFTE: 1
  GPR00: c0000000007e3164 c000001fe4e8ba10 c0000000015c5e00 0000000000000000
  GPR04: 0000000000000001 0000000000000000 0000000000000039 0000000000000299
  GPR08: 0000000000000000 0000000000000001 c000001fe4e88000 0000000000000006
  GPR12: 0000000000000000 c00000000fb40000 c0000000000e6558 c000003ca1bffd00
  GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
  GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000000d52768
  GPR24: c000000000d52740 0000000000000100 c000003ca1b52000 0000000000000002
  GPR28: 0000000000000900 0000000000000000 c00000000152a0c0 c000003ca1b52000
  [1.404226] NIP [c0000000007e33f8] tg3_io_error_detected+0x308/0x340
  [1.404265] LR [c0000000007e3164] tg3_io_error_detected+0x74/0x340

This patch avoids the NULL pointer dereference by moving the access after
the netdev NULL pointer check on tg3_io_error_detected(). Also, we add a
check for netdev being NULL on tg3_io_resume() [suggested by Michael Chan].

Fixes: 0486a063 ("tg3: prevent ifup/ifdown during PCI error recovery")
Fixes: dfc8f370 ("net/tg3: Release IRQs on permanent error")
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yotam Gigi says:

====================
Fix tc-ife bugs

This patch-set contains two bugfixes in the tc-ife action, one fixing some
random behaviour in encode side, and one fixing the decode side packet
parsing logic.

v2->v3
 - Fix the encode side instead of the decode side
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On ife encode side, the action stores the different tlvs inside the ife
header, where each tlv length field should refer to the length of the
whole tlv (without additional padding) and not just the data length.

On ife decode side, the action iterates over the tlvs in the ife header
and parses them one by one, where in each iteration the current pointer is
advanced according to the tlv size.

Before, the encoding encoded only the data length inside the tlv, which led
to false parsing of ife the header. In addition, due to the fact that the
loop counter was unsigned, it could lead to infinite parsing loop.

This fix changes the loop counter to be signed and fixes the encoding to
take into account the tlv type and size.

Fixes: 28a10c42 ("net sched: fix encoding to use real length")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On ife encode side, external mac header is copied from the original packet
and may be overridden if the user requests. Before, the mac header copy
was done from memory region that might not be accessible anymore, as
skb_cow_head might free it and copy the packet. This led to random values
in the external mac header once the values were not set by user.

This fix takes the internal mac header from the packet, after the call to
skb_cow_head.

Fixes: ef6980b6 ("net sched: introduce IFE action")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a pending socket is marked as rejected, we will decrease the
sk_ack_backlog twice. So don't decrement it for rejected sockets
in vsock_pending_work().

Testing of the rejected socket path was done through code
modifications.
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Aditya Sarwade <asarwade@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 62469c76 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:

PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)

This was previously fixed by commit 5dbebbb4 ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.

Without commit 62469c76 we would have the following scenario after
an ifconfig down then up sequence:

- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
  initialized *before* we get to initialize the UniMAC, this is
  critical to ensure the PHY is in a correct state, priv->phydev is
  valid, this code executes fine

- second time from bcmgenet_mii_probe(), through the normal
  phy_init_hw() call (which arguably could be optimized out)

Everything is fine in that case. With commit 62469c76, we would have
the following scenario to happen after an ifconfig down then up
sequence:

- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
  NULL

- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
  bcmgenet_power_up() to initialize the internal PHY, the NULL check
  becomes true, so we do not reset the PHY, yet we keep going on and
  initialize the UniMAC, causing MAC activity to occur

- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
  too late, the PHY is botched, and causes the above bogus pings/packets
  transmission/reception to occur
Reported-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Nelson says:

====================
net: fec: updates to align IP header

This patch series is the outcome of investigation into very high
numbers of alignment faults on kernel 4.1.33 from the linux-fslc
tree:
    https://github.com/freescale/linux-fslc/tree/4.1-1.0.x-imx

The first two patches remove support for the receive accelerator (RACC) from
the i.MX25 and i.MX27 SoCs which don't support the function.

The third patch enables hardware alignment of the ethernet packet payload
(and especially the IP header) to prevent alignment faults in the IP stack.

Testing on i.MX6UL on the 4.1.33 kernel showed that this patch removed
on the order of 70k alignment faults during a 100MiB transfer using
wget.

Testing on an i.MX6Q (SABRE Lite) board on net-next (4.8.0-rc7) showed
a much more modest improvement from 10's of faults, and it's not clear
why that's the case.
====================
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.

Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:

	~/$ cat /proc/cpu/alignment
	User:		0
	System:		72645 (inet_gro_receive+0x104/0x27c)
	Skipped:	0
	Half:		0
	Word:		0
	DWord:		0
	Multi:		72645
	User faults:	3 (fixup+warn)

This patch was suggested by Andrew Lunn in this message to linux-netdev:
	http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2

and adapted from a patch by Russell King from 2014:
	http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8aSigned-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.

	http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdfSigned-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.

http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdfSigned-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the commit below the ipmr/ip6mr rtnl_unicast() code uses the portid
instead of the previous dst_pid which was copied from in_skb's portid.
Since the skb is new the portid is 0 at that point so the packets are sent
to the kernel and we get scheduling while atomic or a deadlock (depending
on where it happens) by trying to acquire rtnl two times.
Also since this is RTM_GETROUTE, it can be triggered by a normal user.

Here's the sleeping while atomic trace:
[ 7858.212557] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
[ 7858.212748] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 7858.212881] 2 locks held by swapper/0/0:
[ 7858.213013]  #0:  (((&mrt->ipmr_expire_timer))){+.-...}, at: [<ffffffff810fbbf5>] call_timer_fn+0x5/0x350
[ 7858.213422]  #1:  (mfc_unres_lock){+.....}, at: [<ffffffff8161e005>] ipmr_expire_process+0x25/0x130
[ 7858.213807] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.0-rc7+ #179
[ 7858.213934] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 7858.214108]  0000000000000000 ffff88005b403c50 ffffffff813a7804 0000000000000000
[ 7858.214412]  ffffffff81a1338e ffff88005b403c78 ffffffff810a4a72 ffffffff81a1338e
[ 7858.214716]  000000000000026c 0000000000000000 ffff88005b403ca8 ffffffff810a4b9f
[ 7858.215251] Call Trace:
[ 7858.215412]  <IRQ>  [<ffffffff813a7804>] dump_stack+0x85/0xc1
[ 7858.215662]  [<ffffffff810a4a72>] ___might_sleep+0x192/0x250
[ 7858.215868]  [<ffffffff810a4b9f>] __might_sleep+0x6f/0x100
[ 7858.216072]  [<ffffffff8165bea3>] mutex_lock_nested+0x33/0x4d0
[ 7858.216279]  [<ffffffff815a7a5f>] ? netlink_lookup+0x25f/0x460
[ 7858.216487]  [<ffffffff8157474b>] rtnetlink_rcv+0x1b/0x40
[ 7858.216687]  [<ffffffff815a9a0c>] netlink_unicast+0x19c/0x260
[ 7858.216900]  [<ffffffff81573c70>] rtnl_unicast+0x20/0x30
[ 7858.217128]  [<ffffffff8161cd39>] ipmr_destroy_unres+0xa9/0xf0
[ 7858.217351]  [<ffffffff8161e06f>] ipmr_expire_process+0x8f/0x130
[ 7858.217581]  [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180
[ 7858.217785]  [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180
[ 7858.217990]  [<ffffffff810fbc95>] call_timer_fn+0xa5/0x350
[ 7858.218192]  [<ffffffff810fbbf5>] ? call_timer_fn+0x5/0x350
[ 7858.218415]  [<ffffffff8161dfe0>] ? ipmr_net_init+0x180/0x180
[ 7858.218656]  [<ffffffff810fde10>] run_timer_softirq+0x260/0x640
[ 7858.218865]  [<ffffffff8166379b>] ? __do_softirq+0xbb/0x54f
[ 7858.219068]  [<ffffffff816637c8>] __do_softirq+0xe8/0x54f
[ 7858.219269]  [<ffffffff8107a948>] irq_exit+0xb8/0xc0
[ 7858.219463]  [<ffffffff81663452>] smp_apic_timer_interrupt+0x42/0x50
[ 7858.219678]  [<ffffffff816625bc>] apic_timer_interrupt+0x8c/0xa0
[ 7858.219897]  <EOI>  [<ffffffff81055f16>] ? native_safe_halt+0x6/0x10
[ 7858.220165]  [<ffffffff810d64dd>] ? trace_hardirqs_on+0xd/0x10
[ 7858.220373]  [<ffffffff810298e3>] default_idle+0x23/0x190
[ 7858.220574]  [<ffffffff8102a20f>] arch_cpu_idle+0xf/0x20
[ 7858.220790]  [<ffffffff810c9f8c>] default_idle_call+0x4c/0x60
[ 7858.221016]  [<ffffffff810ca33b>] cpu_startup_entry+0x39b/0x4d0
[ 7858.221257]  [<ffffffff8164f995>] rest_init+0x135/0x140
[ 7858.221469]  [<ffffffff81f83014>] start_kernel+0x50e/0x51b
[ 7858.221670]  [<ffffffff81f82120>] ? early_idt_handler_array+0x120/0x120
[ 7858.221894]  [<ffffffff81f8243f>] x86_64_start_reservations+0x2a/0x2c
[ 7858.222113]  [<ffffffff81f8257c>] x86_64_start_kernel+0x13b/0x14a

Fixes: 2942e900 ("[RTNETLINK]: Use rtnl_unicast() for rtnetlink unicasts")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to commit 3be07244 ("ip6_gre: fix flowi6_proto value in
xmit path"), set flowi6_proto to IPPROTO_GRE for output route lookup.

Up until now, ip6gre_xmit_other() has set flowi6_proto to a bogus value.
This affected output route lookup for packets sent on an ip6gretap device
in cases where routing was dependent on the value of flowi6_proto.

Since the correct proto is already set in the tunnel flowi6 template via
commit 252f3f5a ("ip6_gre: Set flowi6_proto as IPPROTO_GRE in xmit
path."), simply delete the line setting the incorrect flowi6_proto value.
Suggested-by: Jiri Benc <jbenc@redhat.com>
Fixes: c12b395a ("gre: Support GRE over IPv6")
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If DBGUNDO() is enabled (FASTRETRANS_DEBUG > 1), a compile
error will happen, since inet6_sk(sk)->daddr became sk->sk_v6_daddr

Fixes: efe4208f ("ipv6: make lookups simpler and faster")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With TCP MTU probing enabled and offload TX checksumming disabled,
tcp_mtu_probe() calculated the wrong checksum when a fragment being copied
into the probe's SKB had an odd length. This was caused by the direct use
of skb_copy_and_csum_bits() to calculate the checksum, as it pads the
fragment being copied, if needed. When this fragment was not the last, a
subsequent call used the previous checksum without considering this
padding.

The effect was a stale connection in one way, as even retransmissions
wouldn't solve the problem, because the checksum was never recalculated for
the full SKB length.
Signed-off-by: Douglas Caetano dos Santos <douglascs@taghos.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.8-20160922' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-09-22

this is a pull request of one patch for the upcoming linux-4.8 release.

The patch by Sergei Miroshnichenko fixes a potential deadlock in the generic
CAN device code that cann occour after a bus-off.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Fixes: 2ccccf5f ("net_sched: update hierarchical backlog too")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull media fixes from Mauro Carvalho Chehab:

 - several fixes for new drivers added for Kernel 4.8 addition (cec
   core, pulse8 cec driver and Mediatek vcodec)

 - a regression fix for cx23885 and saa7134 drivers

 - an important fix for rcar-fcp, making rcar_fcp_enable() return 0 on
   success

* tag 'media/v4.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (25 commits)
  [media] cx23885/saa7134: assign q->dev to the PCI device
  [media] rcar-fcp: Make sure rcar_fcp_enable() returns 0 on success
  [media] cec: fix ioctl return code when not registered
  [media] cec: don't Feature Abort broadcast msgs when unregistered
  [media] vcodec:mediatek: Refine VP8 encoder driver
  [media] vcodec:mediatek: Refine H264 encoder driver
  [media] vcodec:mediatek: change H264 profile default to profile high
  [media] vcodec:mediatek: Add timestamp and timecode copy for V4L2 Encoder
  [media] vcodec:mediatek: Fix visible_height larger than coded_height issue in s_fmt_out
  [media] vcodec:mediatek: Fix fops_vcodec_release flow for V4L2 Encoder
  [media] vcodec:mediatek:code refine for v4l2 Encoder driver
  [media] cec-funcs.h: add missing vendor-specific messages
  [media] cec-edid: check for IEEE identifier
  [media] pulse8-cec: fix error handling
  [media] pulse8-cec: set correct Signal Free Time
  [media] mtk-vcodec: add HAS_DMA dependency
  [media] cec: ignore messages when log_addr_mask == 0
  [media] cec: add item to TODO
  [media] cec: set unclaimed addresses to CEC_LOG_ADDR_INVALID
  [media] cec: add CEC_LOG_ADDRS_FL_ALLOW_UNREG_FALLBACK flag
  ...

Pull networking fixes from David Miller:
 "Mostly small bits scattered all over the place, which is usually how
  things go this late in the -rc series.

   1) Proper driver init device resets in bnx2, from Baoquan He.

   2) Fix accounting overflow in __tcp_retransmit_skb(),
      sk_forward_alloc, and ip_idents_reserve, from Eric Dumazet.

   3) Fix crash in bna driver ethtool stats handling, from Ivan Vecera.

   4) Missing check of skb_linearize() return value in mac80211, from
      Johannes Berg.

   5) Endianness fix in nf_table_trace dumps, from Liping Zhang.

   6) SSN comparison fix in SCTP, from Marcelo Ricardo Leitner.

   7) Update DSA and b44 MAINTAINERS entries.

   8) Make input path of vti6 driver work again, from Nicolas Dichtel.

   9) Off-by-one in mlx4, from Sebastian Ott.

  10) Fix fallback route lookup handling in ipv6, from Vincent Bernat.

  11) Fix stack corruption on probe in qed driver, from Yuval Mintz.

  12) PHY init fixes in r8152 from Hayes Wang.

  13) Missing SKB free in irda_accept error path, from Phil Turnbull"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
  tcp: properly account Fast Open SYN-ACK retrans
  tcp: fix under-accounting retransmit SNMP counters
  MAINTAINERS: Update b44 maintainer.
  net: get rid of an signed integer overflow in ip_idents_reserve()
  net/mlx4_core: Fix to clean devlink resources
  net: can: ifi: Configure transmitter delay
  vti6: fix input path
  ipmr, ip6mr: return lastuse relative to now
  r8152: disable ALDPS and EEE before setting PHY
  r8152: remove r8153_enable_eee
  r8152: move PHY settings to hw_phy_cfg
  r8152: move enabling PHY
  r8152: move some functions
  cxgb4/cxgb4vf: Allocate more queues for 25G and 100G adapter
  qed: Fix stack corruption on probe
  MAINTAINERS: Add an entry for the core network DSA code
  net: ipv6: fallback to full lookup if table lookup is unsuitable
  net/mlx5: E-Switch, Handle mode change failures
  net/mlx5: E-Switch, Fix error flow in the SRIOV e-switch init code
  net/mlx5: Fix flow counter bulk command out mailbox allocation
  ...

A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].

To resolve this issue, the restart_timer is replaced by a delayed
work.

[1] https://github.com/victronenergy/venus/issues/24Signed-off-by: Sergei Miroshnichenko <sergeimir@emcraft.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since the TFO socket is accepted right off SYN-data, the socket
owner can call getsockopt(TCP_INFO) to collect ongoing SYN-ACK
retransmission or timeout stats (i.e., tcpi_total_retrans,
tcpi_retransmits). Currently those stats are only updated
upon handshake completes. This patch fixes it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes these under-accounting SNMP rtx stats
LINUX_MIB_TCPFORWARDRETRANS
LINUX_MIB_TCPFASTRETRANS
LINUX_MIB_TCPSLOWSTARTRETRANS
when retransmitting TSO packets

Fixes: 10d3be56 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2016-09-21

1) Propagate errors on security context allocation.
   From Mathias Krause.

2) Fix inbound policy checks for inter address family tunnels.
   From Thomas Zeitlhofer.

3) Fix an old memory leak on aead algorithm usage.
   From Ilan Tayari.

4) A recent patch fixed a possible NULL pointer dereference
   but broke the vti6 input path.
   Fix from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.8-20160921' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-09-21

this is another pull request of one patch for the upcoming linux-4.8 release.

Marek Vasut fixes the CAN-FD bit rate switch in the ifi driver by configuring
the transmitter delay.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Taking over as maintainer since Gary Zambrano is no longer working
for Broadcom.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko reported an UBSAN warning happening in ip_idents_reserve()

[] UBSAN: Undefined behaviour in ./arch/x86/include/asm/atomic.h:156:11
[] signed integer overflow:
[] -2117905507 + -695755206 cannot be represented in type 'int'

Since we do not have uatomic_add_return() yet, use atomic_cmpxchg()
so that the arithmetics can be done using unsigned int.

Fixes: 04ca6973 ("ip: make IP identifiers less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans devlink resources by calling devlink_port_unregister()
to avoid the following issues:

- Kernel panic when triggering reset flow.
- Memory leak due to unfreed resources in mlx4_init_port_info().

Fixes: 09d4d087 ("mlx4: Implement devlink interface")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-09-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.8

iwlwifi

* fix to prevent firmware crash when sending off-channel frames
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since commit 1625f452, vti6 is broken, all input packets are dropped
(LINUX_MIB_XFRMINNOSTATES is incremented).

XFRM_TUNNEL_SKB_CB(skb)->tunnel.ip6 is set by vti6_rcv() before calling
xfrm6_rcv()/xfrm6_rcv_spi(), thus we cannot set to NULL that value in
xfrm6_rcv_spi().

A new function xfrm6_rcv_tnl() that enables to pass a value to
xfrm6_rcv_spi() is added, so that xfrm6_rcv() is not touched (this function
is used in several handlers).

CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Fixes: 1625f452 ("net/xfrm_input: fix possible NULL deref of tunnel.ip6->parms.i_key")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

When I introduced the lastuse member I made a subtle error because it was
returned as an absolute value but that is meaningless to user-space as it
doesn't allow to see how old exactly an entry is. Let's make it similar to
how the bridge returns such values and make it relative to "now" (jiffies).
This allows us to show the actual age of the entries and is much more
useful (e.g. user-space daemons can age out entries, iproute2 can display
the lastuse properly).

Fixes: 43b9e127 ("net: ipmr/ip6mr: add support for keeping an entry age")
Reported-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: correct the flow of PHY

First, to enable the PHY as early as possible. Some settings may fail if the
PHY is power down.

Move the other PHY settings to hw_phy_cfg() to make sure the order is correct.

Finally, disable ALDPS and EEE before updating the PHY for RTL8153.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove r8153_enable_eee().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the PHY relative settings together to hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move enabling PHY to init(), otherwise some other settings may fail.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>