Pull parisc update from Helge Deller:
 - a bugfix for sticon (parisc text console driver) to not crash the
   64bit kernel on machines with more than 4GB RAM
 - added kernel audit support
 - made udelay() implementation SMP-safe
 - "make install" now does not depend on vmlinux
 - added defconfigs for 32- and 64-kernels

* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add generic 32- and 64-bit defconfigs
  parisc: sticon - unbreak on 64bit kernel
  parisc: signal fixup - SIGBUS vs. SIGSEGV
  parisc: implement full version of access_ok()
  parisc: correctly display number of active CPUs
  parisc: do not count IPI calls twice
  parisc: make udelay() SMP-safe
  parisc: remove duplicate define
  parisc: make "make install" not depend on vmlinux
  parisc: add kernel audit feature
  parisc: provide macro to create exception table entries

Pull ARM SoC DT updates from Olof Johansson:
 "Most of this branch consists of updates, additions and general churn
  of the device tree source files in the kernel (arch/arm/boot/dts).
  Besides that, there are a few things to point out:

   - Lots of platform conversion on OMAP2+, with removal of old board
     files for various platforms.
   - Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
     well
   - Some updates to pinctrl and other subsystems.  Most of these are
     for DT-enablement of the various platforms and acks have been
     collected"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
  ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
  ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
  ARM: dts: bcm281xx: Add card detect GPIO
  ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
  ARM: bcm281xx: Add device node for the GPIO controller
  ARM: mvebu: Add Netgear ReadyNAS 104 board
  ARM: tegra: fix Tegra114 IOMMU register address
  ARM: kirkwood: add support for OpenBlocks A7 platform
  ARM: dts: omap4-panda: add DPI pinmuxing
  ARM: dts: AM33xx: Add RNG node
  ARM: dts: AM33XX: Add hwspinlock node
  ARM: dts: OMAP5: Add hwspinlock node
  ARM: dts: OMAP4: Add hwspinlock node
  ARM: dts: use 'status' property for PCIe nodes
  ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
  ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
  ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
  ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
  ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  ...

Pull ARM driver updates from Olof Johansson:
 "Updates of SoC-near drivers and other driver updates that makes more
  sense to take through our tree.  In this case it's involved:

   - Some Davinci driver updates that has required corresponding
     platform code changes (gpio mostly)
   - CCI bindings and a few driver updates
   - Marvell mvebu patches for PCI MSI support (could have gone through
     the PCI tree for this release, but they were acked by Bjorn for
     3.12 so we kept them through arm-soc).
   - Marvell dove switch-over to DT-based PCIe configuration
   - Misc updates for Samsung platform dmaengine drivers"

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
  ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
  dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
  ARM: S3C24XX: Fix possible dma selection warning
  PCI: mvebu: make local functions static
  PCI: mvebu: add I/O access wrappers
  PCI: mvebu: Dynamically detect if the PEX link is up to enable hot plug
  ARM: mvebu: fix gated clock documentation
  ARM: dove: remove legacy pcie and clock init
  ARM: dove: switch to DT probed mbus address windows
  ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
  ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
  dmaengine: add driver for Samsung s3c24xx SoCs
  ARM: S3C24XX: number the dma clocks
  PCI: mvebu: add support for Marvell Dove SoCs
  PCI: mvebu: add support for reset on GPIO
  PCI: mvebu: remove subsys_initcall
  PCI: mvebu: increment nports only for registered ports
  PCI: mvebu: move clock enable before register access
  PCI: mvebu: add support for MSI
  irqchip: armada-370-xp: implement MSI support
  ...

Pull ARM SoC board updates from Olof Johansson:
 "Board-related updates.  This branch is getting smaller and smaller,
  which is the whole idea so that's reassuring.

  Right now by far most of the code is related to shmobile updates, and
  they are now switching over to removal of board code and migration to
  multiplatform, so we'll see their board code base shrink in the near
  future too, I hope.

  In addition to that is some defconfig updates, some display updates
  for OMAP and a bit of new board support for Rockchip boards"

* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (56 commits)
  ARM: rockchip: add support for rk3188 and Radxa Rock board
  ARM: rockchip: add dts for bqcurie2 tablet
  ARM: rockchip: enable arm-global-timer
  ARM: rockchip: move shared dt properties to common source file
  ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
  ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
  ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
  ARM: OMAP2+: drm: Don't build device for DMM
  ARM: tegra: defconfig updates
  RX-51: Add support for OMAP3 ROM Random Number Generator
  ARM: OMAP3: RX-51: ARM errata 430973 workaround
  ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
  ARM: shmobile: marzen: enable INTC IRQ
  ARM: shmobile: bockw: add SMSC support on reference
  ARM: shmobile: Use SMP on Koelsch
  ARM: shmobile: Remove KZM9D reference DTS
  ARM: shmobile: Let KZM9D multiplatform boot with KZM9D DTB
  ARM: shmobile: Remove non-multiplatform KZM9D reference support
  ARM: shmobile: Use KZM9D without reference for multiplatform
  ARM: shmobile: Sync KZM9D DTS with KZM9D reference DTS
  ...

Pull ARM SoC platform changes from Olof Johansson:
 "New and updated SoC support.  Among the things new for this release
  are:

   - More support for the AM33xx platforms from TI
   - Tegra 124 support, and some updates to older tegra families as well
   - imx cleanups and updates across the board
   - A rename of Broadcom's Mobile platforms which were introduced as
     ARCH_BCM, and turned out to be too broad a name.  New name is
     ARCH_BCM_MOBILE.
   - A whole bunch of updates and fixes for integrator, making the
     platform code more modern and switches over to DT-only booting.
   - Support for two new Renesas shmobile chipsets.  Next up for them is
     more work on consolidation instead of introduction of new
     non-multiplatform SoCs, we're all looking forward to that!
   - Misc cleanups for older Samsung platforms, some Allwinner updates,
     etc"

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
  ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
  ARM: bcm_defconfig: Run "make savedefconfig"
  ARM: bcm281xx: Add ARCH Timers to config
  rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
  ARM: vexpress: Enable platform-specific options in defconfig
  ARM: vexpress: Make defconfig work again
  ARM: sunxi: remove .init_time hooks
  ARM: imx: enable suspend for imx6sl
  ARM: imx: ensure dsm_request signal is not asserted when setting LPM
  ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
  ARM: imx6q: move low-power code out of clock driver
  ARM: imx: drop extern with function prototypes in common.h
  ARM: imx: reset core along with enable/disable operation
  ARM: imx: do not return from imx_cpu_die() call
  ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
  ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
  ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
  ARM: imx: replace imx6q_restart() with mxc_restart()
  ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
  ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
  ...

Pull ARM SoC cleanups from Olof Johansson:
 "This branch contains code cleanups, moves and removals for 3.13.

  Qualcomm msm targets had a bunch of code removal for legacy non-DT
  platforms.  Nomadik saw more device tree conversions and cleanup of
  old code.  Tegra has some code refactoring, etc.

  One longish patch series from Sebastian Hasselbarth changes the
  init_time hooks and tries to use a generic implementation for most
  platforms, since they were all doing more or less the same things.

  Finally the "shark" platform is removed in this release.  It's been
  abandoned for a while and nobody seems to care enough to keep it
  around.  If someone comes along and wants to resurrect it, the removal
  can easily be reverted and code brought back.

  Beyond this, mostly a bunch of removals of stale content across the
  board, etc"

* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
  ARM: gemini: convert to GENERIC_CLOCKEVENTS
  ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
  ARM: OMAP3: control: add API for setting IVA bootmode
  ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
  ARM: OMAP3: McBSP: do not access CM register directly
  ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
  ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
  MAINTAINERS: Add patterns for DTS files for AT91
  ARM: at91: remove init_machine() as default is suitable
  ARM: at91/dt: split sama5d3 peripheral definitions
  ARM: at91/dt: split sam9x5 peripheral definitions
  ARM: Remove temporary sched_clock.h header
  ARM: clps711x: Use linux/sched_clock.h
  MAINTAINERS: Add DTS files to patterns for Samsung platform
  ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
  ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
  clk: nomadik: fix missing __init on nomadik_src_init
  ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
  ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
  ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
  ...

Pull ARM SoC low-priority fixes from Olof Johansson:
 "A set of fixes for various platforms that weren't considered bad
  enough to include in 3.12 (nor -stable).  Mostly simple typo fixes,
  etc"

* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP2+: irq, AM33XX add missing register check
  ARM: OMAP2+: wakeupgen: AM43x adaptation
  ARM: OMAP1: Fix a bunch of GPIO related section warnings after initdata got corrected
  ARM: dts: fix PL330 MDMA1 address in DT for Universal C210 board
  ARM: dts: Work around lack of cpufreq regulator lookup for exynos4210-origen and trats boards
  ARM: dts: Fix typo earlyprintk in exynos5440-sd5v1 and ssdk5440 boards
  ARM: dts: Correct typo in use of samsung,pin-drv for exynos5250
  ARM: rockchip: remove obsolete rockchip,config properties
  ARM: rockchip: fix wrong use of non-existent CONFIG_LOCAL_TIMERS
  ARM: mach-omap1: Fix omap1510_fpga_init_irq() implicit declarations.
  ARM: OMAP1: fix incorrect placement of __initdata tag
  ARM: OMAP: remove deprecated IRQF_DISABLED
  ARM: OMAP2+: throw the die id into the entropy pool

Pull ARM64 update from Catalin Marinas:
 "Main features:
   - Ticket-based spinlock implementation and lockless lockref support
   - Big endian support
   - CPU hotplug support, currently for PSCI (Power State Coordination
     Interface) capable firmware
   - Virtual address space extended to 42-bit in the 64K page
     configuration (maximum VA space with 2 levels of page tables)
   - Compat (AArch32) kuser helpers updated to ARMv8 (make use of
     load-acquire/store-release instructions)
   - Code cleanup, defconfig update and minor fixes"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: (43 commits)
  ARM64: /proc/interrupts: display IPIs of online CPUs only
  arm64: locks: Remove CONFIG_GENERIC_LOCKBREAK
  arm64: KVM: vgic: byteswap GICv2 access on world switch if BE
  arm64: KVM: initialize HYP mode following the kernel endianness
  arm64: compat: Clear the IT state independent of the 32-bit ARM or Thumb-2 mode
  arm64: Use 42-bit address space with 64K pages
  arm64: module: ensure instruction is little-endian before manipulation
  arm64: defconfig: Enable CONFIG_PREEMPT by default
  arm64: fix access to preempt_count from assembly code
  arm64: move enabling of GIC before CPUs are set online
  arm64: use generic RW_DATA_SECTION macro in linker script
  arm64: Slightly improve the warning on CPU0 enable-method
  ARM64: simplify cpu_read_bootcpu_ops using OF/DT helper
  ARM64: DT: define ARM64 specific arch_match_cpu_phys_id
  arm64: allow ioremap_cache() to use existing RAM mappings
  arm64: update 32-bit kuser helpers to ARMv8
  arm64: perf: fix event number mask
  arm64: kconfig: allow CPU_BIG_ENDIAN to be selected
  arm64: Fix the endianness of arch_spinlock_t
  arm64: big-endian: write CPU holding pen address as LE
  ...

Pull gfs2 updates from Steven Whitehouse:
 "The main feature of interest this time is quota updates.  There are
  some clean ups and some patches to use the new generic lru list code.

  There is still plenty of scope for some further changes in due course -
  faster lookups of quota structures is very much on the todo list.
  Also, a start has been made towards the more tricky issue of using the
  generic lru code with glocks, but that will have to be completed in a
  subsequent merge window.

  The other, more minor feature, is that there have been a number of
  performance patches which relate to block allocation.  In particular
  they will improve performance when the disk is nearly full"

* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
  GFS2: Use generic list_lru for quota
  GFS2: Rename quota qd_lru_lock qd_lock
  GFS2: Use reflink for quota data cache
  GFS2: Use lockref for glocks
  GFS2: Protect quota sync generation
  GFS2: Inline qd_trylock into gfs2_quota_unlock
  GFS2: Make two similar quota code fragments into a function
  GFS2: Remove obsolete quota tunable
  GFS2: Move gfs2_icbit_munge into quota.c
  GFS2: Speed up starting point selection for block allocation
  GFS2: Add allocation parameters structure
  GFS2: Clean up reservation removal
  GFS2: fix dentry leaks
  GFS2: new function gfs2_rbm_incr
  GFS2: Introduce rbm field bii
  GFS2: Do not reset flags on active reservations
  GFS2: introduce bi_blocks for optimization
  GFS2: optimize rbm_from_block wrt bi_start
  GFS2: d_splice_alias() can't return error

Merge tag 'ftrace-urgent-3.12-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull perf/ftrace fix from Steven Rostedt:
 "Dave Jones's trinity program was able to enable the function tracer
  from a normal user account via the perf syscall "perf_event_open()".
  When I was able to reproduce it with trinity, I was able to track down
  exactly how it happened.

  I discovered that the check for whether the function tracepoint should
  be activated or not was using the "perf_paranoid_kernel()" check which
  by default, lets the user continue.  The user should not by default be
  able to enable function tracing.

  The fix is to use "perf_paranoid_tracepoint_raw()" which will not let
  the user enable function tracing.  This is a security fix as normal
  users should never be allowed to enable the function tracer"

* tag 'ftrace-urgent-3.12-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  perf/ftrace: Fix paranoid level for enabling function tracer

Pull MIPS updates from Ralf Baechle:
 - Some minor work bringing the Cobalt MIPS platforms in line with other
   MIPS platforms
 - Make vmlinux.32 and vmlinux.64 build messages less verbose
 - Always register the R4k clocksource when selected, the clock source's
   rating will decide if this or another clock source is actually going
   to be used
 - Drop support for the Cisco (formerly Scientific Atlanta) PowerTV
   platform.  There appears to be nobody left who cares and the USB
   driver went stale while waiting for years to be merged
 - Some cleanup of Loongson 2 related #ifdefery
 - Various minor cleanups
 - Major rework on all things related to tracing / ptrace on MIPS,
   including switching the MIPS ELF core dumper to regsets, enabling the
   entries for SIGSYS in struct siginfo for MIPS, enabling ftrace
   syscall trace points
 - Some more work to bring DECstation support code in line with other
   more modern code
 - Report the name of the detected CPU, not just its CP0 PrID value
 - Some more BCM 47xx and atheros ath79xx work
 - Support for compressed kernels using the XZ compression scheme

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (53 commits)
  MIPS: remove duplicate define
  MIPS: Random whitespace clean-ups
  MIPS: traps: Reformat notify_die invocations to 80 columns.
  MIPS: Print correct PC in trace dump after NMI exception
  MIPS: kernel: cpu-probe: Report CPU id during probe
  MIPS: Remove unused defines in piix4.h
  MIPS: Get rid of hard-coded values for Malta PIIX4 fixups
  MIPS: Always register R4K clock when selected
  MIPS: Loongson: Get rid of Loongson 2 #ifdefery all over arch/mips.
  MIPS: cacheops.h: Increase indentation by one tab.
  MIPS: Remove bogus BUG_ON()
  MIPS: PowerTV: Remove support code.
  MIPS: ftrace: Add support for syscall tracepoints.
  MIPS: ptrace: Switch syscall reporting to tracehook_report_syscall_entry().
  MIPS: Move audit_arch() helper function to __syscall_get_arch().
  MIPS: Enable HAVE_ARCH_TRACEHOOK.
  MIPS: Switch ELF core dumper to use regsets.
  MIPS: Implement task_user_regset_view.
  MIPS: ptrace: Use tracehook helpers.
  MIPS: O32 / 32-bit: Always copy 4 stack arguments.
  ...

Pull s390 updates from Martin Schwidefsky:
 "The bulk of the patches for the 3.13 merge window.

  Heiko spent quite a bit of work to improve the code generation for the
  kernel.  That includes the exploitation of the interlocked-access
  facility for the atomics and bitops implementation and the improvement
  for the -march and -mtune compiler settings.

  Another important change is the removal of the user_mode=home option,
  user processes now always run in primary space.  The storage keys are
  not initialized at system startup any more, with that the storage key
  removal work is complete.  For the PCI support the hibernation hooks
  have been implemented.

  And as usual cleanup and fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (62 commits)
  s390/scm_blk: fix endless loop for requests != REQ_TYPE_FS
  s390/mm,tlb: correct tlb flush on page table upgrade
  s390/mm: page_table_realloc returns failure
  s390: allow to set gcc -mtune flag
  s390/percpu: remove this_cpu_xor() implementation
  s390/vtime: correct idle time calculation
  s390/time: fix get_tod_clock_ext inline assembly
  tty/hvc_iucv: remove redundant NULL check
  s390/dasd: Write to profile data area only if it is available
  s390: convert use of typedef ctl_table to struct ctl_table
  s390/pci: cleanup function information block
  s390/pci: remove CONFIG_PCI_DEBUG dependancy
  s390/pci: message cleanup
  Update default configuration
  s390: add a couple of useful defconfigs
  s390/percpu: make use of interlocked-access facility 1 instructions
  s390/percpu: use generic percpu ops for CONFIG_32BIT
  s390/compat: make psw32_user_bits a constant value again
  s390: fix handling of runtime instrumentation psw bit
  s390: fix save and restore of the floating-point-control register
  ...

New defconfigs which should be able to boot on any 32/64bit machine.
Many drivers are selected to be compiled-in to avoid the need for an
additional initrd and still being able to boot.
Signed-off-by: Helge Deller <deller@gmx.de>

STI text console (sticon) was broken on 64bit machines with more than
4GB RAM and this lead in some cases to a kernel crash.

Since sticon uses the 32bit STI API it needs to keep pointers to memory
below 4GB. But on a 64bit kernel some memory regions (e.g. the kernel
stack) might be above 4GB which then may crash the kernel in the STI
functions.

Additionally sticon didn't selected the built-in framebuffer fonts by
default. This is now fixed.

On a side-note: Theoretically we could enhance the sticon driver to
use the 64bit STI API. But - beside the fact that some machines don't
provide a 64bit STI ROM - this would just add complexity.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.8+

Clean up code to send correct signal on invalid memory accesses:
Send SIGBUS instead of SIGSEGV for memory accesses outside of mmap'ed
areas

This fixes the mmap13 testcase from the Linux Test Project.
Signed-off-by: Helge Deller <deller@gmx.de>

Up to now PA-RISC could live with a trivial version of access_ok().
Our fault handlers can correctly handle fault cases.

But testcases showed that we need a better access check else we won't
always return correct errno failure codes to userspace.

Problem showed up during 32bit userspace tests in which writev() used a
32bit memory area and length which would then wrap around on 64bit
kernel.
Signed-off-by: Helge Deller <deller@gmx.de>

In case we fail to power up other CPUs in a SMP system, the kernel
currently shows a wrong number of online CPUs. This change makes the
output more verbose on how many of the CPUs are online. Example:

CPU(s): 1 out of 2 PA8800 (Mako) at 900.000000 MHz online.
Signed-off-by: Helge Deller <deller@gmx.de>

The number of IPI calls is already visible as per-cpu IPI irq counters
in/proc/cpuinfo, so let's drop this additional counting.

This partly reverts:
cd85d551 parisc: more irq statistics in /proc/interrupts
Signed-off-by: Helge Deller <deller@gmx.de>

Each CPU has it's own Control Register 16 (CR16) which is used as time source
for the udelay() function. But since the CR16 registers across different CPUs
are not synced, we need to recalculate the loop count if we get switched away
to ensure that we really delay as much time as requested.
Signed-off-by: Helge Deller <deller@gmx.de>

This patch removes a duplicate define from
arch/parisc/math-emu/float.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Helge Deller <deller@gmx.de>

Install targets (install, zinstall, uinstall) on parisc have a
dependency to vmlinux. This may cause parts of the kernel to be rebuilt
during installation. We must avoid this since this may run as root.
Install targets "ABSOLUTELY MUST NOT MODIFY THE SOURCE TREE." as Linus
emphasized this in:

http://lkml.org/lkml/2013/7/10/600

So on parisc and maybe other archs we need the same as for x86:

1648e4f8 x86, kbuild: make "make install" not depend on vmlinux

This parisc patch was inspired by:

19514fc6 arm, kbuild: make "make install" not depend on vmlinux
Signed-off-by: Helge Deller <deller@gmx.de>

Implement missing functions for parisc to provide kernel audit feature.
Signed-off-by: Helge Deller <deller@gmx.de>

Provide a macro ASM_EXCEPTIONTABLE_ENTRY() to create exception table
entries and convert all open-coded places to use that macro.

This patch is a first step toward creating a exception table which only
holds 32bit pointers even on a 64bit kernel. That way in my own kernel
I was able to reduce the in-kernel exception table from 44kB to 22kB.
Signed-off-by: Helge Deller <deller@gmx.de>

Pull CIFS updates from Steve French:
 "Includes a couple of fixes, plus changes to make multiplex identifiers
  easier to read and correlate with network traces, and a set of
  enhancements for SMB3 dialect.  Also adds support for per-file
  compression for both cifs and smb2/smb3 ("chattr +c filename).

  Should have at least one other merge request ready by next week with
  some new SMB3 security features and copy offload support"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  Query network adapter info at mount time for debugging
  Fix unused variable warning when CIFS POSIX disabled
  Allow setting per-file compression via CIFS protocol
  Query File System Alignment
  Query device characteristics at mount time from server on SMB2/3 not just on cifs mounts
  cifs: Send a logoff request before removing a smb session
  cifs: Make big endian multiplex ID sequences monotonic on the wire
  cifs: Remove redundant multiplex identifier check from check_smb_hdr()
  Query file system attributes from server on SMB2, not just cifs, mounts
  Allow setting per-file compression via SMB2/3
  Fix corrupt SMB2 ioctl requests

Pull NFS client updates from Trond Myklebust:
 "Highlights include:

   - Changes to the RPC socket code to allow NFSv4 to turn off
     timeout+retry:
      * Detect TCP connection breakage through the "keepalive" mechanism
   - Add client side support for NFSv4.x migration (Chuck Lever)
   - Add support for multiple security flavour arguments to the "sec="
     mount option (Dros Adamson)
   - fs-cache bugfixes from David Howells:
     * Fix an issue whereby caching can be enabled on a file that is
       open for writing
   - More NFSv4 open code stable bugfixes
   - Various Labeled NFS (selinux) bugfixes, including one stable fix
   - Fix buffer overflow checking in the RPCSEC_GSS upcall encoding"

* tag 'nfs-for-3.13-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (68 commits)
  NFSv4.2: Remove redundant checks in nfs_setsecurity+nfs4_label_init_security
  NFSv4: Sanity check the server reply in _nfs4_server_capabilities
  NFSv4.2: encode_readdir - only ask for labels when doing readdirplus
  nfs: set security label when revalidating inode
  NFSv4.2: Fix a mismatch between Linux labeled NFS and the NFSv4.2 spec
  NFS: Fix a missing initialisation when reading the SELinux label
  nfs: fix oops when trying to set SELinux label
  nfs: fix inverted test for delegation in nfs4_reclaim_open_state
  SUNRPC: Cleanup xs_destroy()
  SUNRPC: close a rare race in xs_tcp_setup_socket.
  SUNRPC: remove duplicated include from clnt.c
  nfs: use IS_ROOT not DCACHE_DISCONNECTED
  SUNRPC: Fix buffer overflow checking in gss_encode_v0_msg/gss_encode_v1_msg
  SUNRPC: gss_alloc_msg - choose _either_ a v0 message or a v1 message
  SUNRPC: remove an unnecessary if statement
  nfs: Use PTR_ERR_OR_ZERO in 'nfs/nfs4super.c'
  nfs: Use PTR_ERR_OR_ZERO in 'nfs41_callback_up' function
  nfs: Remove useless 'error' assignment
  sunrpc: comment typo fix
  SUNRPC: Add correct rcu_dereference annotation in rpc_clnt_set_transport
  ...

The non-IPI interrupts are displayed only for the online cpus from
show_interrupts in kernel/irq/proc.c before calling arch_show_interrupts().
As a result, the column headers and the IPI count don't match if any
CPU is offline.

This patch fixes show_ipi_list to display IPIs for online CPUs only.
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This reverts commit cb26a311.

It mysteriously causes NetworkManager to not find the wireless device
for me.  As far as I can tell, Tejun *meant* for this commit to not make
any semantic changes, but there clearly are some.  So revert it, taking
into account some of the calling convention changes that happened in
this area in subsequent commits.

Cc: Tejun Heo <tj@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull staging driver update from Greg KH:
 "Here's the big drivers/staging/ update for 3.13-rc1.

  Nothing major here, just a _ton_ of fixes and cleanups, mostly driven
  by the new round of OPW applicants, but also there are lots of other
  people doing staging tree cleanups these days in order to help get the
  drivers into mergable shape.

  We also merge, and then revert, the ktap code, as Ingo and the other
  perf/ftrace developers feel it should go into the "real" part of the
  kernel with only a bit more work, so no need to put it in staging for
  now.

  All of this has been in linux-next for a while with no reported
  issues"

* tag 'staging-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1045 commits)
  staging: drm/imx: fix return value check in ipu_add_subdevice_pdata()
  Staging: zram: Fix access of NULL pointer
  Staging: zram: Fix variable dereferenced before check
  Staging: rtl8187se: space prohibited before semicolon in r8185b_init.c
  Staging: rtl8187se: fix space prohibited after that open parenthesis '(' in r8185b_init.c
  Staging: rtl8187se: fix braces {} are not necessary for single statement blocks in r8185b_init.c
  Staging: rtl8187se: fix trailing whitespace in r8185b_init.c
  Staging: rtl8187se: fix please, no space before tabs in r8185b_init.c
  drivers/staging/nvec/Kconfig: remove trailing whitespace
  Staging: dwc2: Fix variable dereferenced before check
  Staging: xgifb: fix braces {} are not necessary for any arm of this statement
  staging: rtl8192e: remove unneeded semicolons
  staging: rtl8192e: use true and false for bool variables
  staging: ft1000: return values corrected in scram_start_dwnld
  staging: ft1000: change values of status return variable in write_dpram32_and_check
  staging: bcm: Remove unnecessary pointer casting
  imx-drm: ipuv3-crtc: Invert IPU DI0 clock polarity
  staging: r8188eu: Fix sparse warnings in rtl_p2p.c
  staging: r8188eu: Fix sparse warnings in rtw_mlme_ext.c
  staging: r8188eu: Fix sparse warnings in rtl8188e.cmd.c
  ...

Pull tty/serial driver updates from Greg KH:
 "Here's the big tty/serial driver update for 3.13-rc1.

  There's some more minor n_tty work here, but nothing like previous
  kernel releases.  Also some new driver ids, driver updates for new
  hardware, and other small things.

  All of this has been in linux-next for a while with no issues"

* tag 'tty-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
  serial: omap: fix missing comma
  serial: sh-sci: Enable the driver on all ARM platforms
  serial: mfd: Staticize local symbols
  serial: omap: fix a few checkpatch warnings
  serial: omap: improve RS-485 performance
  mrst_max3110: fix unbalanced IRQ issue during resume
  serial: omap: Add support for optional wake-up
  serial: sirf: remove duplicate defines
  tty: xuartps: Fix build error when COMMON_CLK is not set
  tty: xuartps: Fix build error due to missing forward declaration
  tty: xuartps: Fix "may be used uninitialized" build warning
  serial: 8250_pci: add Pericom PCIe Serial board Support (12d8:7952/4/8) - Chip PI7C9X7952/4/8
  tty: xuartps: Update copyright information
  tty: xuartps: Implement suspend/resume callbacks
  tty: xuartps: Dynamically adjust to input frequency changes
  tty: xuartps: Updating set_baud_rate()
  tty: xuartps: Force enable the UART in xuartps_console_write
  tty: xuartps: support 64 byte FIFO size
  tty: xuartps: Add polled mode support for xuartps
  tty: xuartps: Implement BREAK detection, add SYSRQ support
  ...

Merge tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core / sysfs patches from Greg KH:
 "Here's the big driver core / sysfs update for 3.13-rc1.

  There's lots of dev_groups updates for different subsystems, as they
  all get slowly migrated over to the safe versions of the attribute
  groups (removing userspace races with the creation of the sysfs
  files.) Also in here are some kobject updates, devres expansions, and
  the first round of Tejun's sysfs reworking to enable it to be used by
  other subsystems as a backend for an in-kernel filesystem.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (83 commits)
  sysfs: rename sysfs_assoc_lock and explain what it's about
  sysfs: use generic_file_llseek() for sysfs_file_operations
  sysfs: return correct error code on unimplemented mmap()
  mdio_bus: convert bus code to use dev_groups
  device: Make dev_WARN/dev_WARN_ONCE print device as well as driver name
  sysfs: separate out dup filename warning into a separate function
  sysfs: move sysfs_hash_and_remove() to fs/sysfs/dir.c
  sysfs: remove unused sysfs_get_dentry() prototype
  sysfs: honor bin_attr.attr.ignore_lockdep
  sysfs: merge sysfs_elem_bin_attr into sysfs_elem_attr
  devres: restore zeroing behavior of devres_alloc()
  sysfs: fix sysfs_write_file for bin file
  input: gameport: convert bus code to use dev_groups
  input: serio: remove bus usage of dev_attrs
  input: serio: use DEVICE_ATTR_RO()
  i2o: convert bus code to use dev_groups
  memstick: convert bus code to use dev_groups
  tifm: convert bus code to use dev_groups
  virtio: convert bus code to use dev_groups
  ipack: convert bus code to use dev_groups
  ...

Pull char/misc patches from Greg KH:
 "Here's the big char/misc driver patchset for 3.13-rc1.

  Lots of stuff in here, including some new drivers for Intel's "MIC"
  co-processor devices, and a new eeprom driver.  Other things include
  the driver attribute cleanups, extcon driver updates, hyperv updates,
  and a raft of other miscellaneous driver fixes.

  All of these have been in linux-next for a while"

* tag 'char-misc-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (121 commits)
  misc: mic: Fixes for randconfig build errors and warnings.
  tifm: fix error return code in tifm_7xx1_probe()
  w1-gpio: Use devm_* functions
  w1-gpio: Detect of_gpio_error for first gpio
  uio: Pass pointers to virt_to_page(), not integers
  uio: fix memory leak
  misc/at24: avoid infinite loop on write()
  misc/93xx46: avoid infinite loop on write()
  misc: atmel_pwm: add deferred-probing support
  mei: wd: host_init propagate error codes from called functions
  mei: replace stray pr_debug with dev_dbg
  mei: bus: propagate error code returned by mei_me_cl_by_id
  mei: mei_cl_link remove duplicated check for open_handle_count
  mei: print correct device state during unexpected reset
  mei: nfc: fix memory leak in error path
  lkdtm: add tests for additional page permissions
  lkdtm: adjust recursion size to avoid warnings
  lkdtm: isolate stack corruption test
  mei: move host_clients_map cleanup to device init
  mei: me: downgrade two errors to debug level
  ...

Pull USB driver update from Greg KH:
 "Here's the big USB driver update for 3.13-rc1.

  It includes the usual xhci changes, EHCI updates to get the scheduling
  of USB transactions working better, and a raft of gadget and musb
  updates as well.

  All of this has been in linux-next for a while with no reported
  issues"

* tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (305 commits)
  USB: Maintainers change for usb serial drivers
  usb: usbtest: support container id descriptor test
  usb: usbtest: support superspeed device capbility descriptor test
  usb: usbtest: support usb2 extension descriptor test
  usb: chipidea: only get vbus regulator for non-peripheral mode
  USB: ehci-atmel: add usb_clk for transition to CCF
  usb: cdc-wdm: ignore speed change notifications
  USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
  usbatm: Fix dynamic_debug / ratelimited atm_dbg and atm_rldbg macros
  printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
  usb: usbtest: support bos descriptor test for usb 3.0
  USB: phy: samsung: Support multiple PHYs of same type
  usb: wusbcore: change WA_SEGS_MAX to a legal value
  usb: wusbcore: add a quirk for Alereon HWA device isoc behavior
  usb: wusbcore: combine multiple isoc frames in a single transfer request.
  usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
  usb: chipidea: host: more enhancement when ci->hcd is NULL
  usb: ohci: remove ep93xx bus glue platform driver
  usb: usbtest: fix checkpatch warning as sizeof code style
  UWB: clean up attribute use by using ATTRIBUTE_GROUPS()
  ...

The current default perf paranoid level is "1" which has
"perf_paranoid_kernel()" return false, and giving any operations that
use it, access to normal users. Unfortunately, this includes function
tracing and normal users should not be allowed to enable function
tracing by default.

The proper level is defined at "-1" (full perf access), which
"perf_paranoid_tracepoint_raw()" will only give access to. Use that
check instead for enabling function tracing.
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: stable@vger.kernel.org # 3.4+
CVE: CVE-2013-2930
Fixes: ced39002 ("ftrace, perf: Add support to use function tracepoint in perf")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

This patch removes a duplicate define from
arch/mips/boot/ecoff.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6081/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The while loop only peeks at the top request in the queue but does
not yet consume it. Since we only handle fs requests, we need to
dequeue and complete all other request command types with error
just in case we would ever receive such an unforeseen request.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Commit 52ea2a56 (arm64: locks: introduce ticket-based spinlock
implementation) introduces the arch_spin_is_contended() function making
CONFIG_GENERIC_LOCKBREAK unnecessary.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>

Ensure that accesses to the GICH_* registers are byteswapped
when the kernel is compiled as big-endian.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Force SCTLR_EL2.EE to 1 if the kernel is compiled as BE.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ARM architecture reference specifies that the IT state bits in the
PSR must be all zeros in ARM mode or behavior is unspecified. If an ARM
function is registered as a signal handler, and that signal is delivered
inside a block of instructions following an IT instruction, some of the
instructions at the beginning of the signal handler may be skipped if
the IT state bits of the Program Status Register are not cleared by the
kernel.
Signed-off-by: T.J. Purtell <tj@mobisocial.us>
[catalin.marinas@arm.com: code comment and commit log updated]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch expands the VA_BITS to 42 when the 64K page configuration is
enabled allowing 2TB kernel linear mapping. Linux still uses 2 levels of
page tables in this configuration with pgd now being a full page.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>