Saeed Mahameed says:

====================
mlx5-updates-2020-03-17

1) Compiler warnings and cleanup for the connection tracking series
2) Bug fixes for the connection tracking series
3) Fix devlink port register sequence
4) Last five patches in the series, By Eli cohen
   Add the support for forwarding traffic between two eswitch uplink
   representors (Hairpin for eswitch), using mlx5 termination tables
   to change the direction of a packet in hw from RX to TX pipeline.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

At least some integrated PHY's in RTL8168/RTL8125 chip versions support
downshift, and the actual link speed can be read from a vendor-specific
register. Info about this register was provided by Realtek.
More details about downshift configuration (e.g. number of attempts)
aren't available, therefore the downshift tunable is not implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit referenced below, hw_stats_type of an entry is set for every
entry that corresponds to a pedit action. However, the assignment is only
done after the entry pointer is bumped, and therefore could overwrite
memory outside of the entries array.

The reason for this positioning may have been that the current entry's
hw_stats_type is already set above, before the action-type dispatch.
However, if there are no more actions, the assignment is wrong. And if
there are, the next round of the for_each_action loop will make the
assignment before the action-type dispatch anyway.

Therefore fix this issue by simply reordering the two lines.

Fixes: 74522e7b ("net: sched: set the hw_stats_type in pedit loop")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum_cnt: Expose counter resources

Jiri says:

Capacity and utilization of existing flow and RIF counters are currently
unavailable to be seen by the user. Use the existing devlink resources
API to expose the information:

$ sudo devlink resource show pci/0000:00:10.0 -v
pci/0000:00:10.0:
  name kvd resource_path /kvd size 524288 unit entry dpipe_tables none
  name span_agents resource_path /span_agents size 8 occ 0 unit entry dpipe_tables none
  name counters resource_path /counters size 79872 occ 44 unit entry dpipe_tables none
    resources:
      name flow resource_path /counters/flow size 61440 occ 4 unit entry dpipe_tables none
      name rif resource_path /counters/rif size 18432 occ 40 unit entry dpipe_tables none
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tests for mlxsw hw_stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement occupancy counting for counters and expose over devlink
resource API.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put all init operations related to subpools into
mlxsw_sp_counter_sub_pools_init().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the validation of subpools configuration, to avoid possible over
commitment to resource registration. Add WARN_ON to indicate bug
in the code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement devlink resources support for counter pools. Move the subpool
sizes calculations into the new resources register function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new field to subpool struct that would indicate which
resource id should be used to query the entry size for
the subpool from the device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the global static array of subpools is used. Make it
per-instance as multiple instances of the mlxsw driver can have
different values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the change that made the code to query counter bank size from device
instead of using hard-coded value, the number of available counters
changed for Spectrum-2. Adjust the limit in the selftests.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bank size is different between Spectrum versions. Also it is
a resource that can be queried. So instead of hard coding the value in
code, query it from the firmware.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chelsio NICs have 3 filter regions, in following order of priority:
1. High Priority (HPFILTER) region (Highest Priority).
2. HASH region.
3. Normal FILTER region (Lowest Priority).

Currently, there's a 1-to-1 mapping between the prio value passed
by TC and the filter region index. However, it's possible to have
multiple TC rules with the same prio value. In this case, if a region
is exhausted, no attempt is made to try inserting the rule in the
next available region.

So, rework and remove the 1-to-1 mapping. Instead, dynamically select
the region to insert the filter rule, as long as the new rule's prio
value doesn't conflict with existing rules across all the 3 regions.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts the following commits:

  8537f786 ("netfilter: Introduce egress hook")
  5418d388 ("netfilter: Generalize ingress hook")
  b030f194 ("netfilter: Rename ingress hook include file")

>From the discussion in [0], the author's main motivation to add a hook
in fast path is for an out of tree kernel module, which is a red flag
to begin with. Other mentioned potential use cases like NAT{64,46}
is on future extensions w/o concrete code in the tree yet. Revert as
suggested [1] given the weak justification to add more hooks to critical
fast-path.

  [0] https://lore.kernel.org/netdev/cover.1583927267.git.lukas@wunner.de/
  [1] https://lore.kernel.org/netdev/20200318.011152.72770718915606186.davem@davemloft.net/Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Miller <davem@davemloft.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Nacked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2020-03-18

please apply the following patch series for qeth to netdev's net-next
tree.

This consists of three parts:
1) support for __GFP_MEMALLOC,
2) several ethtool enhancements (.set_channels, SW Timestamping),
3) the usual cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To check whether a netdevice has already been registered, look at
NETREG_REGISTERED to replace some hacks I added a while ago.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth_do_ioctl() is only reached through our own net_device_ops, so we
can trust that dev->ml_priv still contains what we put there earlier.

qeth_bridgeport_an_set() is an internal function that doesn't require
such sanity checks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Data addresses in the AOB are absolute, and need to be translated before
being fed into kmem_cache_free(). Currently this phys_to_virt() is a no-op.
Also see commit 2db01da8 ("s390/qdio: fill SBALEs with absolute addresses").
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Versions are meaningless for an in-kernel driver.
Instead use the UTS_RELEASE that is set by ethtool_get_drvinfo().

Cc: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for SOF_TIMESTAMPING_TX_SOFTWARE.
No support for non-IQD devices, since they orphan the skb in their xmit
path.

To play nice with TX bulking, set the timestamp when the buffer that
contains the skb(s) is actually flushed out to HW.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For ucast traffic, qeth_iqd_select_queue() falls back to
netdev_pick_tx(). This will potentially use skb_tx_hash() to distribute
the flow over all active TX queues - so txq 0 is a valid selection, and
qeth_iqd_select_queue() needs to check for this and put it on some other
queue. As a result, the distribution for ucast flows is unbalanced and
hits QETH_IQD_MIN_UCAST_TXQ heavier than the other queues.

Open-coding a custom variant of skb_tx_hash() isn't an option, since
netdev_pick_tx() also gives us eg. access to XPS. But we can pull a
little trick: add a single TC class that excludes the mcast txq, and
thus encourage skb_tx_hash() to not pick the mcast txq.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the support for z/VM NICs, but we need to take extra care
about the dedicated mcast queue:

1. netdev_pick_tx() is unaware of this limitation and might select the
   mcast txq. Catch this.
2. require at least _two_ TX queues - one for ucast, one for mcast.
3. when reducing the number of TX queues, there's a potential race
   where netdev_cap_txqueue() over-rules the selected txq index and
   falls back to index 0. This would place ucast traffic on the mcast
   queue, and result in TX errors.
   So for IQD, reject a reduction while the interface is running.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for ETHTOOL_SCHANNELS to change the count of active
TX queues.

Since all TX queue structs are pre-allocated and -registered, we just
need to trivially adjust dev->real_num_tx_queues.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

z/VM NICs don't offer HW QoS for TX rings. So just use netdev_pick_tx()
to distribute the connections equally over all enabled TX queues.

We start with just 1 enabled TX queue (this matches the typical
configuration without prio-queueing). A follow-on patch will allow users
to enable additional TX queues.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When falling back to an allocation from the HW header cache, check if
the skb is eligible for using memory reserves.
This only makes a difference if the cache is empty and needs to be
refilled.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use dev_alloc_page() for backing the RX buffers with pages. This way we
pick up __GFP_MEMALLOC.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next:

1) Use nf_flow_offload_tuple() to fetch flow stats, from Paul Blakey.

2) Add new xt_IDLETIMER hard mode, from Manoj Basapathi.
   Follow up patch to clean up this new mode, from Dan Carpenter.

3) Add support for geneve tunnel options, from Xin Long.

4) Make sets built-in and remove modular infrastructure for sets,
   from Florian Westphal.

5) Remove unused TEMPLATE_NULLS_VAL, from Li RongQing.

6) Statify nft_pipapo_get, from Chen Wandun.

7) Use C99 flexible-array member, from Gustavo A. R. Silva.

8) More descriptive variable names for bitwise, from Jeremy Sowden.

9) Four patches to add tunnel device hardware offload to the flowtable
   infrastructure, from wenxu.

10) pipapo set supports for 8-bit grouping, from Stefano Brivio.

11) pipapo can switch between nibble and byte grouping, also from
    Stefano.

12) Add AVX2 vectorized version of pipapo, from Stefano Brivio.

13) Update pipapo to be use it for single ranges, from Stefano.

14) Add stateful expression support to elements via control plane,
    eg. counter per element.

15) Re-visit sysctls in unprivileged namespaces, from Florian Westphal.

15) Add new egress hook, from Lukas Wunner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 58b09919 ("mptcp: create msk early"), the
msk socket is already available at subflow_syn_recv_sock()
time. Let's move there the state update, to mirror more
closely the first subflow state.

The above will also help multiple subflow supports.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: add phylink support for PCS

This series adds support for IEEE 802.3 register set compliant PCS
for phylink.  In order to do this, we:

1. convert BUG_ON() in existing accessors to WARN_ON_ONCE() and return
   an error.
2. add accessors for modifying a MDIO device register, and use them in
   phylib, rather than duplicating the code from phylib.
3. add support for decoding the advertisement from clause 22 compatible
   register sets for clause 37 advertisements and SGMII advertisements.
4. add support for clause 45 register sets for 10GBASE-R PCS.

These have been tested on the LX2160A Clearfog-CX platform.

v2: eliminate use of BUG_ON() in the accessors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement helpers for PCS accessed via the MII bus using 802.3 clause
45 cycles for 10GBASE-R. Only link up/down is supported, 10G full
duplex is assumed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement helpers for PCS accessed via the MII bus using 802.3 clause
22 cycles, conforming to 802.3 clause 37 and Cisco SGMII specifications
for the advertisement word.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead.  Adapt
__phy_modify_changed() to use the new mdiobus level helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid using BUG_ON() in the mdiobus accessors, prefering instead to use
WARN_ON_ONCE() and returning an error.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: vlan options: add support for tunnel mapping

In order to bring the new vlan API on par with the old one and be able
to completely migrate to the new one we need to support vlan tunnel mapping
and statistics. This patch-set takes care of the former by making it a
vlan option. There are two notable issues to deal with:
 - vlan range to tunnel range mapping
   * The tunnel ids are globally unique for the vlan code and a vlan can
     be mapped to one tunnel, so the old API took care of ranges by
     taking the starting tunnel id value and incrementally mapping
     vlan id(i) -> tunnel id(i). This set takes the same approach and
     uses one new attribute - BRIDGE_VLANDB_ENTRY_TUNNEL_ID. If used
     with a vlan range then it's the starting tunnel id to map.

 - tunnel mapping removal
   * Since there are no reserved/special tunnel ids defined, we can't
     encode mapping removal within the new attribute, in order to be
     able to remove a mapping we add a vlan flag which makes the new
     tunnel option remove the mapping

The rest is pretty straight-forward, in fact we directly re-use the old
code for manipulating tunnels by just mapping the command (set/del). In
order to be able to keep detecting vlan ranges we check that the current
vlan has a tunnel and it's extending the current vlan range end's tunnel
id.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for manipulating vlan/tunnel mappings. The
tunnel ids are globally unique and are one per-vlan. There were two
trickier issues - first in order to support vlan ranges we have to
compute the current tunnel id in the following way:
 - base tunnel id (attr) + current vlan id - starting vlan id
This is in line how the old API does vlan/tunnel mapping with ranges. We
already have the vlan range present, so it's redundant to add another
attribute for the tunnel range end. It's simply base tunnel id + vlan
range. And second to support removing mappings we need an out-of-band way
to tell the option manipulating function because there are no
special/reserved tunnel id values, so we use a vlan flag to denote the
operation is tunnel mapping removal.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new option - BRIDGE_VLANDB_ENTRY_TUNNEL_ID which is used to dump
the tunnel id mapping. Since they're unique per vlan they can enter a
vlan range if they're consecutive, thus we can calculate the tunnel id
range map simply as: vlan range end id - vlan range start id. The
starting point is the tunnel id in BRIDGE_VLANDB_ENTRY_TUNNEL_ID. This
is similar to how the tunnel entries can be created in a range via the
old API (a vlan range maps to a tunnel range).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The vlan tunnel code changes vlan options, it shouldn't touch port or
bridge options so we can constify the port argument. This would later help
us to re-use these functions from the vlan options code.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is more appropriate name as it shows the intent of why we need to
check the options' state. It also allows us to give meaning to the two
arguments of the function: the first is the current vlan (v_curr) being
checked if it could enter the range ending in the second one (range_end).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: stmmac: 100GB Enterprise MAC support

Adds the support for Enterprise MAC IP version which allows operating
speeds up to 100GB.

Patch 1/4, adds the support in XPCS for XLGMII interface that is used in
this kind of Enterprise MAC IPs.

Patch 2/4, adds the XLGMII interface support in stmmac.

Patch 3/4, adds the HW specific support for Enterprise MAC.

We end in patch 4/4, by updating stmmac documentation to mention the
support for this new IP version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>