Makes it easier to find all occurences requesting CONF_MODE_B.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch is similar to that for bfin-uart hardware flow control.
Sport emulated serial device may be probed earlier before GPIOLIB is initialized.
Requesting and configuring CTS GPIO PIN fails in that early stage.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Replace local_irq_disable by local_irq_save.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Blackfin hardware CTS control generate interrupt for both CTS on and off.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Serial device may be probed earlier before GPIOLIB is initialized. Requesting and
configuring CTS GPIO PIN fails in that early stage. Do it when the serial device
really starts up.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

N_HDLC can spoil tty->flags because use not atomic operations on tty->flags.
I use n_hdlc line discipline and it happens.
Signed-off-by: Ilya Zykov <ilya@ilyx.ru>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch converts the drivers in drivers/tty/serial/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch converts the drivers in drivers/parport/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Derrick J. Brashear <shadow@dementia.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.

The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
	.driver = {
-		.bus = &spi_bus_type,
	},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The semantics of UPF_IIR_ONCE (once per serial irq) are only guaranteed
if the kt irq is not shared (once per serial isr in the shared case ==
potentially unwanted reads of the IIR).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Workaround dropped notifications in the iir register.  Prevent reads
coincident with new interrupt notifications by reading the iir at most
once per interrupt.
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

There is no need to call uart_write_wakeup after each character send.
Once at the end of the write sequence is enough.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The function check_modem_status returns an int currently it
is stored in a char.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* git://github.com/rustyrussell/linux:
  virtio-pci: make reset operation safer
  virtio-mmio: Correct the name of the guest features selector
  virtio: add HAS_IOMEM dependency to MMIO platform bus driver

virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.

Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.

This conflicts with how drivers use reset, which is typically:
	reset
	unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.

Fix by flushing out the write, and flushing pending interrupts.

This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Guest features selector spelling mistake.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Fix this compile error on s390:

  CC [M]  drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'

Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
  libata: fix build without BMDMA
  [libata] ahci_platform: fix DT probing

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
  PCI: pciehp: wait 100 ms after Link Training check
  PCI: pciehp: wait 1000 ms before Link Training check
  PCI: pciehp: Retrieve link speed after link is trained
  PCI: Let PCI_PRI depend on PCI
  PCI: Fix compile errors with PCI_ATS and !PCI_IOV
  PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Extend array bounds for all filename chars
  eCryptfs: Flush file in vma close
  eCryptfs: Prevent file create race condition

From mhalcrow's original commit message:

    Characters with ASCII values greater than the size of
    filename_rev_map[] are valid filename characters.
    ecryptfs_decode_from_filename() will access kernel memory beyond
    that array, and ecryptfs_parse_tag_70_packet() will then decrypt
    those characters. The attacker, using the FNEK of the crafted file,
    can then re-encrypt the characters to reveal the kernel memory past
    the end of the filename_rev_map[] array. I expect low security
    impact since this array is statically allocated in the text area,
    and the amount of memory past the array that is accessible is
    limited by the largest possible ASCII filename character.

This patch solves the issue reported by mhalcrow but with an
implementation suggested by Linus to simply extend the length of
filename_rev_map[] to 256. Characters greater than 0x7A are mapped to
0x00, which is how invalid characters less than 0x7A were previously
being handled.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Michael Halcrow <mhalcrow@google.com>
Cc: stable@kernel.org

Dirty pages weren't being written back when an mmap'ed eCryptfs file was
closed before the mapping was unmapped. Since f_ops->flush() is not
called by the munmap() path, the lower file was simply being released.
This patch flushes the eCryptfs file in the vm_ops->close() path.

https://launchpad.net/bugs/870326Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org [2.6.39+]

The file creation path prematurely called d_instantiate() and
unlock_new_inode() before the eCryptfs inode info was fully
allocated and initialized and before the eCryptfs metadata was written
to the lower file.

This could result in race conditions in subsequent file and inode
operations leading to unexpected error conditions or a null pointer
dereference while attempting to use the unallocated memory.

https://launchpad.net/bugs/813146Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Check parent options for iterated tests

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Make i2cdev_notifier_call static
  i2c: Delete ANY_I2C_BUS
  i2c: Fix device name for 10-bit slave address
  i2c-algo-bit: Generate correct i2c address sequence for 10-bit target

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: TPS65910: Fix VDD1/2 voltage selector count

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
  drm: integer overflow in drm_mode_dirtyfb_ioctl()
  drivers/gpu/vga/vgaarb.c: add missing kfree
  drm/radeon/kms/atom: unify i2c gpio table handling
  drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
  ttm: Don't return the bo reserved on error path
  drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
  drm/i915: Fix inconsistent backlight level during disabled
  drm, i915: Fix memory leak in i915_gem_busy_ioctl().
  drm/i915: Use DPCD value for max DP lanes.
  drm/i915: Initiate DP link training only on the lanes we'll be using
  drm/i915: Remove trailing white space
  drm/i915: Try harder during dp pattern 1 link training
  drm/i915: Make DP prepare/commit consistent with DP dpms
  drm/i915: Let panel power sequencing hardware do its job
  drm/i915: Treat PCH eDP like DP in most places
  drm/i915: Remove link_status field from intel_dp structure
  drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
  drm/i915: Module parameters using '-1' as default must be signed type
  drm/i915: Turn on another required clock gating bit on gen6.
  drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
  ...

Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.

Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain

With above expr, number of voltages that can be selected is
step value count * gain count

constant for gain count will be called VDD1_2_NUM_VOLT_COARSE

existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning

drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Last piece of code using ANY_I2C_BUS was deleted almost 2 years ago,
so ANY_I2C_BUS can go away as well.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>

The wrong bits were put on the wire, fix that.

This fixes kernel bug #42562.
Signed-off-by: Sheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>

There is a potential integer overflow in drm_mode_dirtyfb_ioctl()
if userspace passes in a large num_clips.  The call to kmalloc would
allocate a small buffer, and the call to fb->funcs->dirty may result
in a memory corruption.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

This reverts commit dc937280.

As requested by Ben Herrenschmidt:
  "This breaks some powerpc platforms at least.  The practice of having
   a node provide an explicit "interrupt-parent" property pointing to
   itself is an old trick that we've used in the past to allow a
   device-node to have interrupts routed to different controllers.

   In that case, the node also contains an interrupt-map, so the node is
   its own parent, the interrupt resolution hits the map, which then can
   route each individual interrupt to a different parent."

Grant says:
  "Ah, nuts, yes that is broken then.  Yes, please revert the commit and
   Rob & I will come up with a better solution.

   Rob, I think it can be done by explicitly checking for np ==
   desc->interrupt_parent in of_irq_init() instead of relying on
   of_irq_find_parent() returning NULL."
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  mount_subtree() pointless use-after-free
  iio: fix a leak due to improper use of anon_inode_getfd()
  microblaze: bury asm/namei.h