In case of FLUSH operation, BAM copies INPUT EOT FLUSH (0x94)
instead of normal EOT (0x93) tag in input data stream when an
input EOT tag is received during flush operation. So only one tag
will be written instead of 2 separate tags.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The role of FLUSH and EOT tag is to flush already scheduled
descriptors in BAM HW in case of error. EOT is required only
when descriptors are scheduled in RX FIFO. If all the messages
are WRITE, then only FLUSH tag will be used.

A single BAM transfer can have multiple read and write messages.
The EOT and FLUSH tags should be scheduled at the end of BAM HW
descriptors. Since the READ and WRITE can be present in any order
so for some of the cases, these tags are not being written
correctly.

Following is one of the example

   READ, READ, READ, READ

Currently EOT and FLUSH tags are being written after each READ.
If QUP gets NACK for first READ itself, then flush will be
triggered. It will look for first FLUSH tag in TX FIFO and will
stop there so only descriptors for first READ descriptors be
flushed. All the scheduled descriptors should be cleared to
generate BAM DMA completion.

Now this patch is scheduling FLUSH and EOT only once after all the
descriptors. So, flush will clear all the scheduled descriptors and
BAM will generate the completion interrupt.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The rx_nents and tx_nents are redundant. rx_buf and tx_buf can
be used for total number of SG entries. Since rx_buf and tx_buf
give the impression that it is buffer instead of count so rename
it to tx_cnt and rx_cnt for giving it more meaningful variable
name.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

1. Assigns use_dma in qup_dev structure itself which will
   help in subsequent patches to determine the mode in IRQ handler.
2. Does minor code reorganization for loops to reduce the
   unnecessary comparison and assignment.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The QUP BSLP BAM generates the following error sometimes if the
current I2C DMA transfer fails and the flush operation has been
scheduled

    “bam-dma-engine 7884000.dma: Cannot free busy channel”

If any I2C error comes during BAM DMA transfer, then the QUP I2C
interrupt will be generated and the flush operation will be
carried out to make I2C consume all scheduled DMA transfer.
Currently, the same completion structure is being used for BAM
transfer which has already completed without reinit. It will make
flush operation wait_for_completion_timeout completed immediately
and will proceed for freeing the DMA resources where the
descriptors are still in process.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The file has been updated from 2016 to 2018 so fixed the
copyright years.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In case we receive NACK on DATA we shouldn't be resetting the controller,
rather we should issue STOP command. This will terminate the current
transaction and -EIO is returned.

While at that handle the SMBus Quick Command properly.
We shouldn't be setting the XLP9XX_I2C_CMD_READ/WRITE for such
transactions.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

I2C bus enters the STOP condition after the DATA_DONE interrupt is raised.
Essentially the driver should be checking the bus state before sending
any transaction. In case a transaction is initiated while the
bus is busy, the prior transaction's stop condition is not achieved.
Add the check to make sure the bus is not busy before every transaction.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Reviewed-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The hardware may not support SDA hold time configuration, but if it is
not set in the Device Tree either, there is no need to print a warning.
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Free Electrons is now Bootlin, change my email address accordingly
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The errata FE-8471889 description has been updated. There is still a
timing violation for repeated start. But the errata now states that it
was only the case for the Standard mode (100 kHz), in Fast mode (400 kHz)
there is no issue.

This patch limit the errata fix to the Standard mode.

It has been tesed successfully on the clearfog (Aramda 388 based board).
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Suspend functions seem to have been copied from i2c-cadence driver.
Rename the functions to match the rest of the driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

"These patches verify the device id of the PCA984x mux chips using
standardized (but rarely implemented) i2c device identification."

Make sure to not disallow the chips on adapters that are not capable
of reading the device id, but also make sure to check the device id
before writing to the chip.
Tested-by: Adrian Fiergolski <adrian.fiergolski@cern.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>

Can be used during probe to double check that the probed device is
what is expected.

Loosely based on code from Adrian Fiergolski <adrian.fiergolski@cern.ch>.
Tested-by: Adrian Fiergolski <adrian.fiergolski@cern.ch>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>

The buses should honor the firmware interface used to register the device,
but the I2C core reports a MODALIAS of the form i2c:<device> even for I2C
devices registered via OF.

This means that user-space will never get an OF stype uevent MODALIAS even
when the drivers modules contain aliases exported from both the I2C and OF
device ID tables. For example, an Atmel maXTouch Touchscreen registered by
a DT node with compatible "atmel,maxtouch" has the following module alias:

$ cat /sys/class/i2c-adapter/i2c-8/8-004b/modalias
i2c:maxtouch

So udev won't be able to auto-load a module for an OF-only device driver.
Many OF-only drivers duplicate the OF device ID table entries in an I2C ID
table only has a workaround for how the I2C core reports the module alias.

This patch changes the I2C core to report an OF related MODALIAS uevent if
the device was registered via OF. So for the previous example, after this
patch, the reported MODALIAS for the Atmel maXTouch will be the following:

$ cat /sys/class/i2c-adapter/i2c-8/8-004b/modalias
of:NtrackpadT<NULL>Catmel,maxtouch

NOTE: This patch may break out-of-tree drivers that were relying on this
      behavior, and only had an I2C device ID table even when the device
      was registered via OF. There are no remaining drivers in mainline
      that do this, but out-of-tree drivers have to be fixed and define
      a proper OF device ID table to have module auto-loading working.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Dmitry Mastykin <mastichi@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

ACPI_ERROR and ACPI_DEBUG_PRINT are not intended to be used by device
drivers. Use acpi_handle message logging functions instead.

As a nice side effect, it removes the following compiler warnings
which were printed when ACPI debug is disabled:

drivers/i2c/busses/i2c-scmi.c: In function "acpi_smbus_cmi_add_cap":
drivers/i2c/busses/i2c-scmi.c:328:39: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
drivers/i2c/busses/i2c-scmi.c:338:12: warning: suggest braces around empty body in an "else" statement [-Wempty-body]
Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Accesses to SB800_PIIX4_SMB_IDX can occur from multiple drivers.
One example for another driver is the sp5100_tco driver.

Use request_muxed_region() to ensure synchronization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The piix4 i2c driver is extremely slow. Replacing msleep()
with usleep_range() increases its speed substantially.
Use sleep ranges similar to those used in the i2c-801 driver
to keep things simple.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use Kernel coding style for better readability.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Peter Rosin <peda@axentia.se>

Document support for the IIC Bus Interface for DVFS (IIC for DVFS) in
the Renesas M3-N (r8a77965) SoC.

No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The pointer reg is assigned a value that is never read, it is later
overwritten with a new value, hence the redundant initialization can
be removed.

Cleans up clang warning:
drivers/i2c/busses/i2c-stm32f4.c:352:16: warning: Value stored to 'reg'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

HSI2C_MASTER_ST_LOSE state is not documented properly, extensive tests
show that hardware is usually able to recover from this state without
interrupting the transfer. Moreover documentation says that
such state can be caused by slave clock stretching, and should not be
treated as an error during transaction. The only place it indicates
an error is just before starting transaction. In such case bus recovery
procedure should be performed - master should pulse SCL line nine times
and then send STOP condition, it can be repeated until SDA goes high.
The procedure can be performed using manual commands HSI2C_CMD_READ_DATA
and HSI2C_CMD_SEND_STOP.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In case of transaction with I2C_M_RECV_LEN set, make sure the driver reads
the first byte and then updates the RX fifo with the expected length. Set
threshold to 1 byte so that driver gets an interrupt on receiving the first byte.
After which the transfer length is updated depending on the received length.
Also report SMBus block read functionality.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Fix the driver violation of the common practice to return
ENXIO error on a slave address NACK.
Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: George Cherian <george.cherian@cavium.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

R-Car D3 (R8A77995) SoC has a R-Car Gen3-compatible I2C controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

of_get_property() is a bit cumbersome to use. Replace it with the newer
of_property_read_u32() for more readable code.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The very same check is done when calling i2c_new_device(). Remove it
here to avoid code duplication.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

'result' is mostly used in the kernel as int for functions returning
errno on failure. Here it is a pointer to the client struct, so let's
call it this way (as the parent function does, too).
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When debugging a ref counting problem, I overlooked this snipplet a few
times. Might be taste, but I think the new location is visually easier
recognizable.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If we cannot create a device, this is an error, not a warning. Fix the
log level.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull Xtensa fixes from Max Filippov:
 "Two fixes for reserved memory/DMA buffers allocation in high memory on
  xtensa architecture

   - fix memory accounting when reserved memory is in high memory region

   - fix DMA allocation from high memory"

* tag 'xtensa-20180225' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: support DMA buffers in high memory
  xtensa: fix high memory/reserved memory collision

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes:

   - UAPI data type correction for hyperv

   - correct the cpu cores field in /proc/cpuinfo on CPU hotplug

   - return proper error code in the resctrl file system failure path to
     avoid silent subsequent failures

   - correct a subtle accounting issue in the new vector allocation code
     which went unnoticed for a while and caused suspend/resume
     failures"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations
  x86/topology: Fix function name in documentation
  x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system
  x86/apic/vector: Handle vector release on CPU unplug correctly
  genirq/matrix: Handle CPU offlining proper
  x86/headers/UAPI: Use __u64 instead of u64 in <uapi/asm/hyperv.h>

Pull perf fix from Thomas Gleixner:
 "A single commit which shuts up a bogus GCC-8 warning"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/oprofile: Fix bogus GCC-8 warning in nmi_setup()

Pull locking fixes from Thomas Gleixner:
 "Three patches to fix memory ordering issues on ALPHA and a comment to
  clarify the usage scope of a mutex internal function"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs
  locking/xchg/alpha: Clean up barrier usage by using smp_mb() in place of __ASM__MB
  locking/xchg/alpha: Add unconditional memory barrier to cmpxchg()
  locking/mutex: Add comment to __mutex_owner() to deter usage

Pull cleanup patchlet from Thomas Gleixner:
 "A single commit removing a bunch of bogus double semicolons all over
  the tree"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  treewide/trivial: Remove ';;$' typo noise

Pull NFS client bugfixes from Trond Myklebust:

 - fix a broken cast in nfs4_callback_recallany()

 - fix an Oops during NFSv4 migration events

 - make struct nlmclnt_fl_close_lock_ops static

* tag 'nfs-for-4.16-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: make struct nlmclnt_fl_close_lock_ops static
  nfs: system crashes after NFS4ERR_MOVED recovery
  NFSv4: Fix broken cast in nfs4_callback_recallany()

Pull powerpc fixes from Michael Ellerman:

 - Add handling for a missing instruction in our 32-bit BPF JIT so that
   it can be used for seccomp filtering.

 - Add a missing NULL pointer check before a function call in new EEH
   code.

 - Fix an error path in the new ocxl driver to correctly return EFAULT.

 - The support for the new ibm,drc-info device tree property turns out
   to need several fixes, so for now we just stop advertising to
   firmware that we support it until the bugs can be ironed out.

 - One fix for the new drmem code which was incorrectly modifying the
   device tree in place.

 - Finally two fixes for the RFI flush support, so that firmware can
   advertise to us that it should be disabled entirely so as not to
   affect performance.

Thanks to: Bharata B Rao, Frederic Barrat, Juan J. Alvarez, Mark Lord,
Michael Bringmann.

* tag 'powerpc-4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Support firmware disable of RFI flush
  powerpc/pseries: Support firmware disable of RFI flush
  powerpc/mm/drmem: Fix unexpected flag value in ibm,dynamic-memory-v2
  powerpc/bpf/jit: Fix 32-bit JIT for seccomp_data access
  powerpc/pseries: Revert support for ibm,drc-info devtree property
  powerpc/pseries: Fix duplicate firmware feature for DRC_INFO
  ocxl: Fix potential bad errno on irq allocation
  powerpc/eeh: Fix crashes in eeh_report_resume()

Pull networking fixes from David Miller:

 1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.

 2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.

 3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.

 4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.

 5) Fix potential deadlocks in netfilter getsockopt() code paths, from
    Paolo Abeni.

 6) Netfilter stackpointer size checks really are needed to validate
    user input, from Florian Westphal.

 7) Missing timer init in x_tables, from Paolo Abeni.

 8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.

 9) When an ibmvnic device is brought down then back up again, it can be
    sent queue entries from a previous session, handle this properly
    instead of crashing. From Thomas Falcon.

10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.

11) When we are dumping filters in cls_api, the output SKB is empty, and
    the filter we are dumping is too large for the space in the SKB, we
    should return -EMSGSIZE like other netlink dump operations do.
    Otherwise userland has no signal that is needs to increase the size
    of its read buffer. From Roman Kapl.

12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.

13) Module refcount leak in netlink when a dump start fails, from Jason
    Donenfeld.

14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
    from Eric Dumazet.

15) Releasing bpf per-cpu arraymaps can take a long time, add a
    condtional scheduling point. From Eric Dumazet.

16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
    Daniel Borkmann.

17) Fix page leak in gianfar driver, from Andy Spencer.

18) Missed clearing of estimator scratch buffer, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net_sched: gen_estimator: fix broken estimators based on percpu stats
  gianfar: simplify FCS handling and fix memory leak
  ipv6 sit: work around bogus gcc-8 -Wrestrict warning
  macvlan: fix use-after-free in macvlan_common_newlink()
  bpf, arm64: fix out of bounds access in tail call
  bpf, x64: implement retpoline for tail call
  rxrpc: Fix send in rxrpc_send_data_packet()
  net: aquantia: Fix error handling in aq_pci_probe()
  bpf: fix rcu lockdep warning for lpm_trie map_free callback
  bpf: add schedule points in percpu arrays management
  regulatory: add NUL to request alpha2
  ibmvnic: Fix early release of login buffer
  net/smc9194: Remove bogus CONFIG_MAC reference
  net: ipv4: Set addr_type in hash_keys for forwarded case
  tcp_bbr: better deal with suboptimal GSO
  smsc75xx: fix smsc75xx_set_features()
  netlink: put module reference if dump start fails
  selftests/bpf/test_maps: exit child process without error in ENOMEM case
  selftests/bpf: update gitignore with test_libbpf_open
  selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
  ..