The AXP20X_OFF define is an actual specific bit, define it as such.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add the bitops.h header as we need it, alphabetize header order.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The OLinuXino Lime2 has a big capacitor on its LDO3 output. It is
actually too large, causing the PMIC to shutdown when toggling the LDO3.

By enabling soft-start and ramp delay we increase the time for the
capacitor to charge lowering the current drain on the power regulator.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.

What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.

Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.

As a work-around, implement software-based 'regulator-soft-start'
property for AXP209 LDO3 regulator, which is used to first bring up
the LDO3 to the lowest possible voltage and then enable the LDO.

After that, we can set the requested voltage as usual.

Combining this setting with the regulator-ramp-delay allows LDO3 to
come up slowly and staggered, potentially reducing overall inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.

What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.

Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.

As a work-around, we use the soft-start constraint of the regulator
node to first bring up the LDO3 to the lowest possible voltage and
then enable the LDO. After that, we can set the requested voltage
as usual.

Combining this setting with the regulator-ramp-delay allows LDO3 to
enable voltage slowly and staggered, potentially reducing overall
inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3, therefore we can use the standard 'regulator-ramp-delay'
property for those 2 regulators.

Note that the voltage ramp only works when the regulator is already
enabled. E.g. when going from say 0.7 V to 3.6 V.

When turning on the regulator, no voltage ramp is performed in hardware.

What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.

This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.

When turning on the regulator, no voltage ramp is performed in hardware.

What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The current axp20x names the ramping register 'scal' which probably
means scaling. Since the register really has nothing to do with
scaling, but really is the voltage ramp we rename it appropriately.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/axp20x' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.21

This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds a maintainer for the MCP16502 PMIC
driver.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch describes the compatible and the device tree
bindings necessary for the MCP16502 PMIC.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add documentation for regulator modes and suspend states.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Implement shutdown method to make sure the PMIC will not enter the suspend
state when the system is shutdown.

This work is based on work done by Borris Brezillon on [1].

[1] https://www.spinics.net/lists/kernel/msg2942960.htmlSigned-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix line over 80 chars checkpatch.pl warning.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The regulator supports a dedicated suspend mode.
Implement the appropriate ->set_suspend_xx() hooks, add support for
->set_mode(), and provide basic PM ops functionalities to setup the
regulator in a suspend state when the system is entering suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops,
 fix checkpatch warning, adapt commit message, add LDO modes support,
 move modes constants to active-semi,8945a-regulator.h, remove rdevs from
 struct act8945a_pmic, add op_mode to act8945a_pmic]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Unlock expert registers for act8945a.
This is based on orginal work of Boris Brezillon at [1].

[1] https://www.spinics.net/lists/kernel/msg2942960.htmlSigned-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the Arizona LDO1 driver becomes
redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the wm8994 driver becomes redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

At the end of regulator_resolve_supply() we have historically turned
on our supply in some cases.  This could be for one of two reasons:

1. If resolving supplies was happening before the call to
   set_machine_constraints() we needed to predict if
   set_machine_constraints() was going to turn the regulator on and we
   needed to preemptively turn the supply on.
2. Maybe set_machine_constraints() happened before we could resolve
   supplies (because we failed the first time to resolve) and thus we
   might need to propagate an enable that already happened up to our
   supply.

Historically regulator_resolve_supply() used _regulator_is_enabled()
to decide whether to turn on the supply.

Let's change things a little bit.  Specifically:

1. Let's try to enable the supply and the regulator in the same place,
   both in set_machine_constraints().  This means that we have exactly
   the same logic for enabling the supply and the regulator.
2. Let's properly set use_count when we enable always-on or boot-on
   regulators even for those that don't have supplies.  The previous
   commit 1fc12b05 ("regulator: core: Avoid propagating to
   supplies when possible") only did this right for regulators with
   supplies.
3. Let's make it clear that the only time we need to enable the supply
   in regulator_resolve_supply() is if the main regulator is currently
   in use.  By using use_count (like the rest of the code) to decide
   if we're going to enable our supply we keep everything consistent.

Overall the new scheme should be cleaner and easier to reason about.
In addition to fixing regulator_summary to be more correct (because of
the more correct use_count), this change also has the effect of no
longer using _regulator_is_enabled() in this code path.
_regulator_is_enabled() could return an error code for some regulators
at bootup (like RPMh) that can't read their initial state.  While one
can argue that the design of those regulators is sub-optimal, the new
logic sidesteps this brokenness.  This fix in particular fixes
observed problems on Qualcomm sdm845 boards which use the
above-mentioned RPMh regulator.  Those problems were made worse by
commit 1fc12b05 ("regulator: core: Avoid propagating to supplies
when possible") because now we'd think at bootup that the SD
regulators were already enabled and we'd never try them again.

Fixes: 1fc12b05 ("regulator: core: Avoid propagating to supplies when possible")
Reported-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'for-linus' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.21

The GPIO descriptors used by the S2MPS11 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.

Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The GPIO descriptors used by the TPS65090 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.

Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The GPIO descriptors used by the S5M8767 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.

Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The GPIO descriptors used by the DA9211 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.

Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The probe path of this driver is a bit complex: sometimes the
GPIO descriptor is passed to the regulator core, sometimes
it is not.

To handle it in a simple way: stick with the devm_* resource
management and unhinge the GPIO descriptor devres handling
right before passing it to the regulator core, if we pass it
to the regulator core.

Fixes: e7d2be69 ("regulator: max8973: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This adds a function named devm_gpiod_unhinge() that removes
the resource management from a GPIO descriptor.

I am not sure if this is the best anglosaxon name for the
function, no other managed resources have an equivalent
currently, but I chose "unhinge" as the closest intuitive
thing I could imagine that fits Rusty Russell's API design
criterions "the obvious use is the correct one" and
"the name tells you how to use it".

The idea came out of a remark from Mark Brown that it should
be possible to handle over management of a resource from
devres to the regulator core, and indeed we can do that.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When we get a nonexeclusive GPIO descriptor using managed
resources, we should only add it to the list of managed
resources once: on the first user. Augment the
devm_gpiod_get_index() and devm_gpiod_get_from_of_node()
calls to account for this by checking if the descriptor
is already resource managed before we proceed to allocate
a new resource management struct.

Fixes: b0ce7b29 ("regulator/gpio: Allow nonexclusive GPIO access")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This makes gpiod_get_from_of_node() respect the
GPIOD_FLAGS_BIT_NONEXCLUSIVE flag which is especially
nice when getting regulator GPIOs right out of device
tree nodes.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: b0ce7b29 ("regulator/gpio: Allow nonexclusive GPIO access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the gpiod_get_from_of_node() rather than the devm_*
version so that the regulator core can handle the lifecycle
of these descriptors.

Fix up the errorpath so that we free this descriptor if
an error occurs in the callback. Rely on the regulator
core to deal with it after this point: a previous patch
fixed up the regulator core to properly dispose any
GPIO descriptors once you call regulator_register().

Fixes: 96392c3d ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This function already exist inside gpiolib, we were just
reluctant to make it available to the kernel at large as
the devm_* seemed to be enough for anyone.

However we found out that regulators need to do their own
lifecycle/refcounting on GPIO descriptors and explicitly
call gpiod_put() when done with a descriptor, so export
this function so we can hand the refcounting over to the
regulator core for these descriptors after retrieveal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

Fixes: d7a261c2 ("regulator: max8952: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

Fixes: 2468f0d5 ("regulator: lp8788-ldo: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

Fixes: b2d751b7 ("regulator: lm363x: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

Fixes: efdfeb07 ("regulator: fixed: Convert to use GPIO descriptor only")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

If a GPIO descriptor is passed to the regulator_register()
function inside the config->ena_gpiod callers must be
sure that once they call this API the regulator core
owns that descriptor and will make sure to issue
gpiod_put() on it, no matter whether the call is
successful or not.

For device tree regulators, the regulator core will
automatically set up regulator init data from the device
tree when registering a regulator by calling
regulator_of_get_init_data() which in turn calls down to
the regulator driver's .of_parse_cb() callback.
This callback (in drivers such as for max77686) may also
choose to fill in the config->ena_gpiod field with a GPIO
descriptor.

Harden the errorpath of regulator_register() to
properly gpiod_put() any passed in cfg->ena_gpiod
or any gpiod coming from the device tree on any type
of error.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull networking fixes from David Miller:
 "A decent batch of fixes here. I'd say about half are for problems that
  have existed for a while, and half are for new regressions added in
  the 4.20 merge window.

   1) Fix 10G SFP phy module detection in mvpp2, from Baruch Siach.

   2) Revert bogus emac driver change, from Benjamin Herrenschmidt.

   3) Handle BPF exported data structure with pointers when building
      32-bit userland, from Daniel Borkmann.

   4) Memory leak fix in act_police, from Davide Caratti.

   5) Check RX checksum offload in RX descriptors properly in aquantia
      driver, from Dmitry Bogdanov.

   6) SKB unlink fix in various spots, from Edward Cree.

   7) ndo_dflt_fdb_dump() only works with ethernet, enforce this, from
      Eric Dumazet.

   8) Fix FID leak in mlxsw driver, from Ido Schimmel.

   9) IOTLB locking fix in vhost, from Jean-Philippe Brucker.

  10) Fix SKB truesize accounting in ipv4/ipv6/netfilter frag memory
      limits otherwise namespace exit can hang. From Jiri Wiesner.

  11) Address block parsing length fixes in x25 from Martin Schiller.

  12) IRQ and ring accounting fixes in bnxt_en, from Michael Chan.

  13) For tun interfaces, only iface delete works with rtnl ops, enforce
      this by disallowing add. From Nicolas Dichtel.

  14) Use after free in liquidio, from Pan Bian.

  15) Fix SKB use after passing to netif_receive_skb(), from Prashant
      Bhole.

  16) Static key accounting and other fixes in XPS from Sabrina Dubroca.

  17) Partially initialized flow key passed to ip6_route_output(), from
      Shmulik Ladkani.

  18) Fix RTNL deadlock during reset in ibmvnic driver, from Thomas
      Falcon.

  19) Several small TCP fixes (off-by-one on window probe abort, NULL
      deref in tail loss probe, SNMP mis-estimations) from Yuchung
      Cheng"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
  net/sched: cls_flower: Reject duplicated rules also under skip_sw
  bnxt_en: Fix _bnxt_get_max_rings() for 57500 chips.
  bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.
  bnxt_en: Keep track of reserved IRQs.
  bnxt_en: Fix CNP CoS queue regression.
  net/mlx4_core: Correctly set PFC param if global pause is turned off.
  Revert "net/ibm/emac: wrong bit is used for STA control"
  neighbour: Avoid writing before skb->head in neigh_hh_output()
  ipv6: Check available headroom in ip6_xmit() even without options
  tcp: lack of available data can also cause TSO defer
  ipv6: sr: properly initialize flowi6 prior passing to ip6_route_output
  mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
  mlxsw: spectrum_router: Relax GRE decap matching check
  mlxsw: spectrum_switchdev: Avoid leaking FID's reference count
  mlxsw: spectrum_nve: Remove easily triggerable warnings
  ipv4: ipv6: netfilter: Adjust the frag mem limit when truesize changes
  sctp: frag_point sanity check
  tcp: fix NULL ref in tail loss probe
  tcp: Do not underestimate rwnd_limited
  net: use skb_list_del_init() to remove from RX sublists
  ...

Pull x86 fixes from Ingo Molnar:
 "Three fixes: a boot parameter re-(re-)fix, a retpoline build artifact
  fix and an LLVM workaround"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vdso: Drop implicit common-page-size linker flag
  x86/build: Fix compiler support check for CONFIG_RETPOLINE
  x86/boot: Clear RSDP address in boot_params for broken loaders