Move the code to enter Auto Select Mode down to be able to use cfi->cfiq
members to add support for chips using alternative sequence / unlock
addresses.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add a kirkwood_nand_init_rnb() call to allow boards which
have RnB line detection to register this instead of a
static delay.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Add support for a board to register a callback to get the state of the
RnB line if it has it attached.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

2GB xD card, and 4MB SmartMedia ROM card share same ID, so to make both work
split xD and smartmedia ID tables.

Hardware driver must be able to know which type it handles (and probably just one).
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

On i.MX21 SoCs, if the NFC_CONFIG1:NFC_INT_MASK bit is set,
NFC_CONFIG2:NFC_INT always reads out zero, even if an
operation is completed.  This patch uses enable_irq and
disable_irq_nosync instead of NFC_CONFIG1:NFC_INT_MASK to
mask NFC interrupts.  This allows NFC_CONFIG2:NFC_INT to also
be used to detect operation completion on i.MX21.

The i.MX21 NFC does not signal reset completion using
NFC_CONFIG1:NFC_INT_MASK, so instead reset completion is
tested by checking if NFC_CONFIG2 becomes 0.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch allows the mxc_nand driver to reset the NAND
flash controller.  NFC registers are (re-)set after
completion of the reset, as a reset will have reverted
the NFC registers to their default values.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This is to support custom partitioning schemes for embedded PPC. To use
define your own mtd_part_parser and then add something like:
   linux,part-probe = "my_probe", "cmdlinepart";
To the board's dts file.

If linux,part-probe is not specified then this behaves the same as before.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Use kzalloc rather than the combination of kmalloc and memset.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,size,flags;
statement S;
@@

-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
 if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Use kzalloc rather than the combination of kmalloc and memset.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,size,flags;
statement S;
@@

-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
 if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

drivers/mtd/nand/denali.c:1427: error: conflicting types for ‘enable_dma’
arch/powerpc/include/asm/dma.h:189: note: previous definition of ‘enable_dma’ was here
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

There is more work to be done on this but it is basically working now.
Signed-off-by: Jason Roberts <jason.e.roberts@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch fixes a build failure[1] by simply moving the function mtd_to_flctl
beneath the definition of sh_flctl which it uses.

BF introduced by patch
'mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macro' (67026418)
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Conflicts:
	drivers/mtd/mtdcore.c

Pull in the bdi fixes and ARM platform changes that other outstanding
patches depend on.

The revision in SVR for MPC5123 is 3.  The NFC is the same as MPC5121
revision 2.
Signed-off-by: Steve Deiters <SteveDeiters@basler.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

All the SST25L series flash parts have uniform erase sectors.  Remove
the extra MTD_DEBUG_LEVEL2 messages showing the eraseregions info
since they could never be shown.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Ensure that the flash device is in a quiescent state before rebooting.
The implementation is closely modeled after the cfi_cmdset_0001 reboot
notifier, commit 963a6fb0 .
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The pxa32xx_nand driver doesn't support partition tables from the
command line. This patch adds support for it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Remove unused #include <linux/version.h>('s) in
  drivers/mtd/nand/bcm_umi_nand.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Leo Chen <leochen@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Moved the debugging message before the call to map_destroy, which frees its
argument.  The message is also slightly changed to reflect its new
position.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E,E2;
@@

del_mtd_device(E)
...
(
  E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The use of a memcpy() during a spinlock operation will cause very long
thread context switch delays if the flash chip bandwidth is low and the
data to be copied large, because a spinlock will disable preemption.

For example: A flash with 6,5 MB/s bandwidth will cause under ubifs,
which request sometimes 128 KiB (the flash erase size), a preemption delay of
20 milliseconds. High priority threads will not be served during this
time, regardless whether this threads access the flash or not. This behavior
breaks real time.

The patch changes all the use of spin_lock operations for xxxx->mutex
into mutex operations, which is exact what the name says and means.

I have checked the code of the drivers and there is no use of atomic
pathes like interrupt or timers. The mtdoops facility will also not be used
by this drivers. So it is dave to replace the spin_lock against mutex.

There is no performance regression since the mutex is normally not
acquired.

Changelog:
 06.03.2010 First release
 26.03.2010 Fix mutex[1] issue and tested it for compile failure
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Functions omap2_onenand_write_bufferram() and omap3_onenand_write_bufferram()
map the write buffer and store the returned handle in variable dma_src. However,
when DMA unmap is done, variable dma_dst is used instead of the correct dma_src.

This patch fixes them to use the correct DMA buffer.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Convert all magic numbers into appropriate defines, and move the defines
out of the global namespace and into this one driver.  No other driver
needs to care about the MMR layout anyways.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

We do not need these names. Moreover, there are spelling typos
there: "nansin" instead of "nandsim".

This patch is just a clean up, no functional changes.
Reported-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

include/linux/mtd/mtdram.h:6: ERROR: code indent should use tabs where possible
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] Retry commands with UNIT_ATTENTION sense codes to fix ext3/ext4 I/O error
  [SCSI] Enable retries for SYNCRONIZE_CACHE commands to fix I/O error
  [SCSI] scsi_debug: virtual_gb ignores sector_size
  [SCSI] libiscsi: regression: fix header digest errors
  [SCSI] fix locking around blk_abort_request()
  [SCSI] advansys: fix narrow board error path

commit 672917dc ("cpuidle: menu governor: reduce latency on exit")
added an optimization, where the analysis on the past idle period moved
from the end of idle, to the beginning of the new idle.

Unfortunately, this optimization had a bug where it zeroed one key
variable for new use, that is needed for the analysis.  The fix is
simple, zero the variable after doing the work from the previous idle.

During the audit of the code that found this issue, another issue was
also found; the ->measured_us data structure member is never set, a
local variable is always used instead.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Corrado Zoccolo <czoccolo@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://neil.brown.name/md:
  md: restore ability of spare drives to spin down.
  md/raid6: Fix raid-6 read-error correction in degraded state

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  pcmcia: fix compilation after 16bit state locking changes
  pcmcia: order userspace suspend and resume requests
  pcmcia: avoid pccard_validate_cis failure in resume callpath

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  blk-cgroup: Fix an RCU warning in blkiocg_create()
  blk-cgroup: Fix RCU correctness warning in cfq_init_queue()
  drbd: don't expose failed local READ to upper layers

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/ttm: Remove the ttm_bo_block_reservation() function.
  drm/ttm: Remove some leftover debug messages.
  drm/radeon: async event synchronization for drmWaitVblank

Move initialization of the virtio framework before the initialization of
mtd, so that block2mtd can be used on virtio-based block devices.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15644Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Fix RCU issues in the NFSv4 delegation code
  NFSv4: Fix the locking in nfs_inode_reclaim_delegation()

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: sleep: init_set_sci_en_on_resume for Dell Studio 155x
  ACPI: fix acpi_hest_firmware_first_pci() caused oops
  sbshc: acpi_device_class "smbus_host_controller" too long
  power_meter: acpi_device_class "power_meter_resource" too long
  acpi_pad: "processor_aggregator" name too long
  PNP: don't check for conflicts with bridge windows
  ACPI: DMI init_set_sci_en_on_resume for multiple Lenovo ThinkPads
  PNPACPI: compute Address Space length rather than using _LEN
  ACPI: silence kmemcheck false positive

* 'v4l_for_2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB: pxa_camera: move fifo reset direct before dma start
  V4L/DVB: video: testing unsigned for less than 0
  V4L/DVB: mx1-camera: compile fix
  V4L/DVB: budget: Oops: "BUG: unable to handle kernel NULL pointer 	dereference"
  V4L/DVB: ngene: Workaround for stuck DiSEqC pin
  V4L/DVB: saa7146: fix regression of the av7110/budget-av driver
  V4L/DVB: v4l: fix config dependencies: mxb and saa7191 are V4L2 drivers, not V4L1
  V4L/DVB: feature-removal: announce videotext.h removal
  V4L/DVB: V4L - vpfe capture - fix for kernel crash
  V4L/DVB: gspca: make usb id 0461:0815 get handled by the right driver
  V4L/DVB: gspca - stv06xx: Remove the 046d:08da from the stv06xx driver
  V4L/DVB: gspca - sn9c20x: Correct onstack wait_queue_head declaration
  V4L/DVB: saa7146: fix up bytesperline if it is an impossible value
  V4L/DVB: V4L: vpfe_capture - free ccdc_lock when memory allocation fails
  V4L/DVB: V4L - Makfile:Removed duplicate entry of davinci
  V4L/DVB: omap24xxcam: potential buffer overflow

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: create rcu_my_thread_group_empty() wrapper
  memcg: css_id() must be called under rcu_read_lock()
  cgroup: Check task_lock in task_subsys_state()
  sched: Fix an RCU warning in print_task()
  cgroup: Fix an RCU warning in alloc_css_id()
  cgroup: Fix an RCU warning in cgroup_path()
  KEYS: Fix an RCU warning in the reading of user keys
  KEYS: Fix an RCU warning

Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down.  Device failure/removal
etc are still recorded on spares.

However commit 51d5668c broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:

   This means that the alignment between 'odd/even' and
    'clean/dirty' might take a little longer to attain,

how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.

So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately.  There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update).  We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org