The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor. For this, refactor the code to use a central
error path.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The watchdog maximum timeout value is determined by the number of bits
for the interval timer counter, its source clock frequency, the number
of bits of the prescaler and maximum divider value.

This can be calculated with the following equation:

max_timeout = counter / (freq / (max_prescale + 1) / max_divider)

Setting a maximum timeout value will allow the watchdog core to refuse
user-space calls to the WDIOC_SETTIMEOUT ioctl that sets not supported
timeout values.

For example, systemd tries to set a timeout of 10 minutes on reboot to
ensure that the machine will be rebooted even if a reboot failed. This
leads to the following error message on an Exynos5422 Odroid XU4 board:

[  147.986045] s3c2410-wdt 101d0000.watchdog: timeout 600 too big
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

According to Server Base System Architecture (SBSA) specification,
the SBSA Generic Watchdog has two stage timeouts: the first signal (WS0)
is for alerting the system by interrupt, the second one (WS1) is a real
hardware reset.
More details about the hardware specification of this device:
ARM DEN0029B - Server Base System Architecture (SBSA)

This driver can operate ARM SBSA Generic Watchdog as a single stage watchdog
or a two stages watchdog, it's set up by the module parameter "action".
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
In the two stages mode, when the timeout is reached, the first signal (WS0)
will trigger panic. If the system is getting into trouble and cannot be reset
by panic or restart properly by the kdump kernel(if supported), then the
second stage (as long as the first stage) will be reached, system will be
reset by WS1. This function can help administrator to backup the system
context info by panic console output or kdump.

This driver bases on linux kernel watchdog framework, so it can get
timeout from module parameter and FDT at the driver init stage.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Tested-by: Pratyush Anand <panand@redhat.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The sbsa-gwdt.txt documentation in devicetree/bindings/watchdog is for
introducing SBSA(Server Base System Architecture) Generic Watchdog
device node info into FDT.

Also add sbsa-gwdt introduction in watchdog-parameters.txt
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The WinSystems EBC-C384 has an onboard watchdog timer. The timeout range
supported by the watchdog timer is 1 second to 255 minutes. Timeouts
under 256 seconds have a 1 second granularity, while the rest have a 1
minute granularity.

This driver adds watchdog timer support for this onboard watchdog timer.
The timeout may be configured via the timeout module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add support for the watchdog timer on NI cRIO-903x and cDAQ-913x real-
time controllers.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The 'action' (or restart mode) and data parameters may be used by restart
handlers, so they should be passed to the restart callback functions.

Cc: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The Zodiac watchdog is implemented on a microcontoller. The reset reason
currently labelled "trigger" is not to detect when the watchdog has
triggered (as had been initially understood and suggested by the naming),
but to inform the reader that the watchdog, which in fact has it's own
hardware watchdog, has been reset because the hardware watchdog has
triggered. Renaming to "hw watchdog".
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Calling return copy_to_user(...) in an ioctl will not do the right thing
if there's a pagefault: copy_to_user returns the number of bytes not
copied in this case.

Fix up watchdog/rc32434_wdt to do
	return copy_to_user(...)) ?  -EFAULT : 0;

instead.

Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The BCM7038 watchdog driver is specific to Broadcom ARM and MIPS
SoCs so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The driver uses the atomic_io_modify() function to update registers, but
that function is only available on 32-bit ARM. Recent changes have added
ARCH_MVEBU support to 64-bit ARM and hence allowed this driver to build
on 64-bit ARM where this function isn't available and thereby causing
allmodconfig builds to break.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The Technologic Systems TS-4800 is an i.MX515 board, so its drivers
are useless unless building a SOC_IMX51 kernel, except for build
testing purposes.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

As used in (and tested on) the ASRock IMB-150 board. Implementation is
identical to other NCT chips, just with different registers.
Signed-off-by: Rob Kramer <rob@solution-space.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull perf fixes from Thomas Gleixner:
 "A rather largish series of 12 patches addressing a maze of race
  conditions in the perf core code from Peter Zijlstra"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Robustify task_function_call()
  perf: Fix scaling vs. perf_install_in_context()
  perf: Fix scaling vs. perf_event_enable()
  perf: Fix scaling vs. perf_event_enable_on_exec()
  perf: Fix ctx time tracking by introducing EVENT_TIME
  perf: Cure event->pending_disable race
  perf: Fix race between event install and jump_labels
  perf: Fix cloning
  perf: Only update context time when active
  perf: Allow perf_release() with !event->ctx
  perf: Do not double free
  perf: Close install vs. exit race

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - Hopefully the last ASM CLAC fixups

   - A fix for the Quark family related to the IMR lock which makes
     kexec work again

   - A off-by-one fix in the MPX code.  Ironic, isn't it?

   - A fix for X86_PAE which addresses once more an unsigned long vs
     phys_addr_t hickup"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mpx: Fix off-by-one comparison with nr_registers
  x86/mm: Fix slow_virt_to_phys() for X86_PAE again
  x86/entry/compat: Add missing CLAC to entry_INT80_32
  x86/entry/32: Add an ASM_CLAC to entry_SYSENTER_32
  x86/platform/intel/quark: Change the kernel's IMR lock bit to false

Pull scheduler fixlet from Thomas Gleixner:
 "A trivial printk typo fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix trivial typo in printk() message

Pull irq fixes from Thomas Gleixner:
 "Four small fixes for irqchip drivers:

   - Add missing low level irq handler initialization on mxs, so
     interrupts can acutally be delivered

   - Add a missing barrier to the GIC driver

   - Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
     and a cache flush beyond the actual region"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
  irqchip/mxs: Add missing set_handle_irq()
  irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
  irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1

Pull staging/android fix from Greg KH:
 "Here is one patch, for the android binder driver, to resolve a
  reported problem.  Turns out it has been around for a while (since
  3.15), so it is good to finally get it resolved.

  It has been in linux-next for a while with no reported issues"

* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE

Pull USB fixes from Greg KH:
 "Here are a few USB fixes for 4.5-rc6

  They fix a reported bug for some USB 3 devices by reverting the recent
  patch, a MAINTAINERS change for some drivers, some new device ids, and
  of course, the usual bunch of USB gadget driver fixes.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  MAINTAINERS: drop OMAP USB and MUSB maintainership
  usb: musb: fix DMA for host mode
  usb: phy: msm: Trigger USB state detection work in DRD mode
  usb: gadget: net2280: fix endpoint max packet for super speed connections
  usb: gadget: gadgetfs: unregister gadget only if it got successfully registered
  usb: gadget: remove driver from pending list on probe error
  Revert "usb: hub: do not clear BOS field during reset device"
  usb: chipidea: fix return value check in ci_hdrc_pci_probe()
  usb: chipidea: error on overflow for port_test_write
  USB: option: add "4G LTE usb-modem U901"
  USB: cp210x: add IDs for GE B650V3 and B850V3 boards
  USB: option: add support for SIM7100E
  usb: musb: Fix DMA desired mode for Mentor DMA engine
  usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage
  usb: dwc2: USB_DWC2 should depend on HAS_DMA
  usb: dwc2: host: fix the data toggle error in full speed descriptor dma
  usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc
  usb: dwc3: Fix assignment of EP transfer resources
  usb: dwc2: Add extra delay when forcing dr_mode

Pull vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  do_last(): ELOOP failure exit should be done after leaving RCU mode
  should_follow_link(): validate ->d_seq after having decided to follow
  namei: ->d_inode of a pinned dentry is stable only for positives
  do_last(): don't let a bogus return value from ->open() et.al. to confuse us
  fs: return -EOPNOTSUPP if clone is not supported
  hpfs: don't truncate the file when delete fails

Pull ARM SoC fixes from Olof Johansson:
 "We didn't have a batch last week, so this one is slightly larger.

  None of them are scary though, a handful of fixes for small DT pieces,
  replacing properties with newer conventions.

  Highlights:
   - N900 fix for setting system revision
   - onenand init fix to avoid filesystem corruption
   - Clock fix for audio on Beaglebone-x15
   - Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)

  + misc smaller stuff"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Extend info, add wiki and ml for meson arch
  MAINTAINERS: alpine: add a new maintainer and update the entry
  ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
  ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
  Revert "regulator: tps65217: remove tps65217.dtsi file"
  ARM: shmobile: Remove shmobile_boot_arg
  ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss
  ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
  ARM: shmobile: Move shmobile_scu_base from .text to .bss
  ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
  ARM: OMAP2+: Improve omap_device error for driver writers
  ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
  ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
  ARM: OMAP2+: Set system_rev from ATAGS for n900
  ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
  ARM: dts: kirkwood: use unique machine name for ds112
  ARM: dts: imx6: remove bogus interrupt-parent from CAAM node

... or we risk seeing a bogus value of d_is_symlink() there.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... otherwise d_is_symlink() above might have nothing to do with
the inode value we've got.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

both do_last() and walk_component() risk picking a NULL inode out
of dentry about to become positive, *then* checking its flags and
seeing that it's not negative anymore and using (already stale by
then) value they'd fetched earlier.  Usually ends up oopsing soon
after that...

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... into returning a positive to path_openat(), which would interpret that
as "symlink had been encountered" and proceed to corrupt memory, etc.
It can only happen due to a bug in some ->open() instance or in some LSM
hook, etc., so we report any such event *and* make sure it doesn't trick
us into further unpleasantness.

Cc: stable@vger.kernel.org # v3.6+, at least
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

-EBADF is a rather confusing error if an operations is not supported,
and nfsd gets rather upset about it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The delete opration can allocate additional space on the HPFS filesystem
due to btree split. The HPFS driver checks in advance if there is
available space, so that it won't corrupt the btree if we run out of space
during splitting.

If there is not enough available space, the HPFS driver attempted to
truncate the file, but this results in a deadlock since the commit
7dd29d8d ("HPFS: Introduce a global mutex
and lock it on every callback from VFS").

This patch removes the code that tries to truncate the file and -ENOSPC is
returned instead. If the user hits -ENOSPC on delete, he should try to
delete other files (that are stored in a leaf btree node), so that the
delete operation will make some space for deleting the file stored in
non-leaf btree node.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org	# 2.6.39+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge fixes from Andrew Morton:
 "10 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  dax: move writeback calls into the filesystems
  dax: give DAX clearing code correct bdev
  ext4: online defrag not supported with DAX
  ext2, ext4: only set S_DAX for regular inodes
  block: disable block device DAX by default
  ocfs2: unlock inode if deleting inode from orphan fails
  mm: ASLR: use get_random_long()
  drivers: char: random: add get_random_long()
  mm: numa: quickly fail allocations for NUMA balancing on full nodes
  mm: thp: fix SMP race condition between THP page fault and MADV_DONTNEED

Pull ext2/4 DAX fix from Ted Ts'o:
 "This fixes a file system corruption bug with DAX"

* tag 'tags/ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext2, ext4: fix issue with missing journal entry in ext4_dax_mkwrite()

Pull PCI fixes from Bjorn Helgaas:
 "Enumeration:
    Revert x86 pcibios_alloc_irq() to fix regression (Bjorn Helgaas)

  Marvell MVEBU host bridge driver:
    Restrict build to 32-bit ARM (Thierry Reding)"

* tag 'pci-v4.5-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: mvebu: Restrict build to 32-bit ARM
  Revert "PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()"
  Revert "PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed"
  Revert "x86/PCI: Don't alloc pcibios-irq when MSI is enabled"

As it is currently written ext4_dax_mkwrite() assumes that the call into
__dax_mkwrite() will not have to do a block allocation so it doesn't create
a journal entry.  For a read that creates a zero page to cover a hole
followed by a write that actually allocates storage this is incorrect.  The
ext4_dax_mkwrite() -> __dax_mkwrite() -> __dax_fault() path calls
get_blocks() to allocate storage.

Fix this by having the ->page_mkwrite fault handler call ext4_dax_fault()
as this function already has all the logic needed to allocate a journal
entry and call __dax_fault().

Also update the ext2 fault handlers in this same way to remove duplicate
code and keep the logic between ext2 and ext4 the same.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Pull clk fix from Stephen Boyd:
 "One small fix to keep OMAP platforms working across a suspend/resume
  cycle"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: ti: omap3+: dpll: use non-locking version of clk_get_rate

Previously calls to dax_writeback_mapping_range() for all DAX filesystems
(ext2, ext4 & xfs) were centralized in filemap_write_and_wait_range().

dax_writeback_mapping_range() needs a struct block_device, and it used
to get that from inode->i_sb->s_bdev.  This is correct for normal inodes
mounted on ext2, ext4 and XFS filesystems, but is incorrect for DAX raw
block devices and for XFS real-time files.

Instead, call dax_writeback_mapping_range() directly from the filesystem
->writepages function so that it can supply us with a valid block
device.  This also fixes DAX code to properly flush caches in response
to sync(2).
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dax_clear_blocks() needs a valid struct block_device and previously it
was using inode->i_sb->s_bdev in all cases.  This is correct for normal
inodes on mounted ext2, ext4 and XFS filesystems, but is incorrect for
DAX raw block devices and for XFS real-time devices.

Instead, rename dax_clear_blocks() to dax_clear_sectors(), and change
its arguments to take a bdev and a sector instead of an inode and a
block.  This better reflects what the function does, and it allows the
filesystem and raw block device code to pass in an appropriate struct
block_device.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Online defrag operations for ext4 are hard coded to use the page cache.
See ext4_ioctl() -> ext4_move_extents() -> move_extent_per_page()

When combined with DAX I/O, which circumvents the page cache, this can
result in data corruption.  This was observed with xfstests ext4/307 and
ext4/308.

Fix this by only allowing online defrag for non-DAX files.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When S_DAX is set on an inode we assume that if there are pages attached
to the mapping (mapping->nrpages != 0), those pages are clean zero pages
that were used to service reads from holes.  Any dirty data associated
with the inode should be in the form of DAX exceptional entries
(mapping->nrexceptional) that is written back via
dax_writeback_mapping_range().

With the current code, though, this isn't always true.  For example,
ext2 and ext4 directory inodes can have S_DAX set, but have their dirty
data stored as dirty page cache entries.  For these types of inodes,
having S_DAX set doesn't really make sense since their I/O doesn't
actually happen through the DAX code path.

Instead, only allow S_DAX to be set for regular inodes for ext2 and
ext4.  This allows us to have strict DAX vs non-DAX paths in the
writeback code.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recent *sync enabling discovered that we are inserting into the
block_device pagecache counter to the expectations of the dirty data
tracking for dax mappings.  This can lead to data corruption.

We want to support DAX for block devices eventually, but it requires
wider changes to properly manage the pagecache.

   dump_stack+0x85/0xc2
   dax_writeback_mapping_range+0x60/0xe0
   blkdev_writepages+0x3f/0x50
   do_writepages+0x21/0x30
   __filemap_fdatawrite_range+0xc6/0x100
   filemap_write_and_wait+0x4a/0xa0
   set_blocksize+0x70/0xd0
   sb_set_blocksize+0x1d/0x50
   ext4_fill_super+0x75b/0x3360
   mount_bdev+0x180/0x1b0
   ext4_mount+0x15/0x20
   mount_fs+0x38/0x170

Mark the support broken so its disabled by default, but otherwise still
available for testing.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When doing append direct io cleanup, if deleting inode fails, it goes
out without unlocking inode, which will cause the inode deadlock.

This issue was introduced by commit cf1776a9 ("ocfs2: fix a tiny
race when truncate dio orohaned entry").
Signed-off-by: Guozhonghua <guozhonghua@h3c.com>
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: <stable@vger.kernel.org>	[4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>