Both of them create and initialize lists, which are not touched
by another foreing pernet_operations.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are:
1)dev_proc_ops and dev_mc_net_ops, which create and destroy
pernet proc file and not interesting for another net namespaces;
2)netdev_net_ops, which creates pernet hashes, which are not
touched by another pernet_operations.

So, make them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch starts to convert pernet_subsys, registered
from subsys initcalls.

It seems safe to be executed in parallel with others,
as it's only creates/destoyes proc entry,
which nobody else is not interested in.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

uevent_net_init() and uevent_net_exit() create and
destroy netlink socket, and these actions serialized
in netlink code.

Parallel execution with other pernet_operations
makes the socket disappear earlier from uevent_sock_list
on ->exit. As userspace can't be interested in broadcast
messages of dying net, and, as I see, no one in kernel
listen them, we may safely make uevent_net_ops async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch starts to convert pernet_subsys, registered
from postcore initcalls.

audit_net_init() creates netlink socket, while audit_net_exit()
destroys it. The rest of the pernet_list are not interested
in the socket, so we make audit_net_ops async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnetlink_net_init() and rtnetlink_net_exit()
create and destroy netlink socket net::rtnl.

The socket is used to send rtnl notification via
rtnl_net_notifyid(). There is no a problem
to create and destroy it in parallel with other
pernet operations, as we link net in setup_net()
after the socket is created, and destroy
in cleanup_net() after net is unhashed from all
the lists and there is no RCU references on it.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The methods of netlink_net_ops create and destroy "netlink"
file, which are not interesting for foreigh pernet_operations.
So, netlink_net_ops may safely be made async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_defaults_ops introduce only net_defaults_init_net method,
and it acts on net::core::sysctl_somaxconn, which
is not interesting for the rest of pernet_subsys and
pernet_device lists. Then, make them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_inuse_ops methods expose statistics in /proc.
No one from the rest of pernet_subsys or pernet_device
lists touch net::core::inuse.

So, it's safe to make net_inuse_ops async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pernet_operations would have had a problem in parallel
execution with others, if init_net had been able to released.
But it's not, and the rest is safe for that.
There is memory allocation, which nobody else interested in,
and sysctl registration. So, we make them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Methods netfilter_net_init() and netfilter_net_exit()
initialize net::nf::hooks and change net-related proc
directory of net. Another pernet_operations are not
interested in forein net::nf::hooks or proc entries,
so it's safe to make them executed in parallel with
methods of other pernet operations.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch starts to convert pernet_subsys, registered
from core initcalls.

Methods sysctl_net_init() and sysctl_net_exit() initialize
net::sysctls table of a namespace.

pernet_operations::init()/exit() methods from the rest
of the list do not touch net::sysctls of strangers,
so it's safe to execute sysctl_pernet_ops's methods
in parallel with any other pernet_operations.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch starts to convert pernet_subsys, registered
from pure initcalls.

net_ns_ops::net_ns_net_init/net_ns_net_init, methods use only
ida_simple_* functions, which are not need a synchronization.
They are synchronized by idr subsystem.

So, net_ns_ops methods are able to be executed
in parallel with methods of other pernet operations.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch starts to convert pernet_subsys, registered
before initcalls.

proc_net_ns_ops::proc_net_ns_init()/proc_net_ns_exit()
{un,}register pernet net->proc_net and ->proc_net_stat.

Constructors and destructors of another pernet_operations
are not interested in foreign net's proc_net and proc_net_stat.
Proc filesystem privitives are synchronized on proc_subdir_lock.

So, proc_net_ns_ops methods are able to be executed
in parallel with methods of any other pernet operations.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds new pernet_operations::async flag to indicate operations,
which ->init(), ->exit() and ->exit_batch() methods are allowed
to be executed in parallel with the methods of any other pernet_operations.

When there are only asynchronous pernet_operations in the system,
net_mutex won't be taken for a net construction and destruction.

Also, remove BUG_ON(mutex_is_locked()) from net_assign_generic()
without replacing with the equivalent net_sem check, as there is
one more lockdep assert below.

v3: Add comment near net_mutex.
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sem protects from pernet_list changing, while
ops_free_list() makes simple kfree(), and it can't
race with other pernet_operations callbacks.

So we may release net_mutex earlier then it was.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the mutex is mostly used to protect pernet operations
list. It orders setup_net() and cleanup_net() with parallel
{un,}register_pernet_operations() calls, so ->exit{,batch} methods
of the same pernet operations are executed for a dying net, as
were used to call ->init methods, even after the net namespace
is unlinked from net_namespace_list in cleanup_net().

But there are several problems with scalability. The first one
is that more than one net can't be created or destroyed
at the same moment on the node. For big machines with many cpus
running many containers it's very sensitive.

The second one is that it's need to synchronize_rcu() after net
is removed from net_namespace_list():

Destroy net_ns:
cleanup_net()
  mutex_lock(&net_mutex)
  list_del_rcu(&net->list)
  synchronize_rcu()                                  <--- Sleep there for ages
  list_for_each_entry_reverse(ops, &pernet_list, list)
    ops_exit_list(ops, &net_exit_list)
  list_for_each_entry_reverse(ops, &pernet_list, list)
    ops_free_list(ops, &net_exit_list)
  mutex_unlock(&net_mutex)

This primitive is not fast, especially on the systems with many processors
and/or when preemptible RCU is enabled in config. So, all the time, while
cleanup_net() is waiting for RCU grace period, creation of new net namespaces
is not possible, the tasks, who makes it, are sleeping on the same mutex:

Create net_ns:
copy_net_ns()
  mutex_lock_killable(&net_mutex)                    <--- Sleep there for ages

I observed 20-30 seconds hangs of "unshare -n" on ordinary 8-cpu laptop
with preemptible RCU enabled after CRIU tests round is finished.

The solution is to convert net_mutex to the rw_semaphore and add fine grain
locks to really small number of pernet_operations, what really need them.

Then, pernet_operations::init/::exit methods, modifying the net-related data,
will require down_read() locking only, while down_write() will be used
for changing pernet_list (i.e., when modules are being loaded and unloaded).

This gives signify performance increase, after all patch set is applied,
like you may see here:

%for i in {1..10000}; do unshare -n bash -c exit; done

*before*
real 1m40,377s
user 0m9,672s
sys 0m19,928s

*after*
real 0m17,007s
user 0m5,311s
sys 0m11,779

(5.8 times faster)

This patch starts replacing net_mutex to net_sem. It adds rw_semaphore,
describes the variables it protects, and makes to use, where appropriate.
net_mutex is still present, and next patches will kick it out step-by-step.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Line up destructors actions in the revers order
to constructors. Next patches will add more actions,
and this will be comfortable, if there is the such
order.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch merges two repeating pieces of code in one,
and they will live in setup_net() now.

The only change is that assignment:

	init_net_initialized = true;

becomes reordered with:

	list_add_tail_rcu(&net->list, &net_namespace_list);

The order does not have visible effect, and it is a simple
cleanup because of:

init_net_initialized is used in !CONFIG_NET_NS case
to order proc_net_ns_ops registration occuring at boot time:

	start_kernel()->proc_root_init()->proc_net_init(),
with
	net_ns_init()->setup_net(&init_net, &init_user_ns)

also occuring in boot time from the same init_task.

When there are no another tasks to race with them,
for the single task it does not matter, which order
two sequential independent loads should be made.
So we make them reordered.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2018-02-12

This series contains updates to i40e and i40evf.

Alan fixes a spelling mistake in code comments.  Fixes an issue on older
firmware versions or NPAR enabled PFs which do not support the
I40E_FLAG_DISABLE_FW_LLDP flag and would get into a situation where any
attempt to change any priv flag would be forbidden.

Alex got busy with the ITR code and made several cleanups and fixes so
that we can more easily understand what is going on.  The fixes included
a computational fix when determining the register offset, as well as a
fix for unnecessarily toggling the CLEARPBA bit which could lead to
potential lost events if auto-masking is not enabled.

Filip adds a necessary delay to recover after a EMP reset when using
firmware version 4.33.

Paweł adds a warning message for MFP devices when the link-down-on-close
flag is set because it may affect other partitions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.

The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.

The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.

One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.

The first value current_itr represents the current value of the register.

The second value target_itr represents the desired value of the register.

The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

While testing code for the recent ITR changes I found that updating the Tx
ITR appeared to have no effect with everything defaulting to the Rx ITR. A
bit of digging narrowed it down the fact that we were asking the PF to
associate all causes with ITR 0 as we weren't populating the itr_idx values
for either Rx or Tx.

To correct it I have added the configuration for these values to this
patch. In addition I did some minor clean-up to just add a local pointer
for the vector map instead of dereferencing it based off of the index
repeatedly. In my opinion this makes the resultant code a bit more readable
and saves us a few characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of using the register value for the defines when setting up the
ring ITR we can just use the actual values and avoid the use of shifts and
macros to translate between the values we have and the values we want.

This helps to make the code more readable as we can quickly translate from
one value to the other.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Changes since v1:
Added changes in these files:
    drivers/infiniband/hw/usnic/usnic_transport.c
    drivers/staging/lustre/lnet/lnet/lib-socket.c
    drivers/target/iscsi/iscsi_target_login.c
    drivers/vhost/net.c
    fs/dlm/lowcomms.c
    fs/ocfs2/cluster/tcp.c
    security/tomoyo/network.c

Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.

"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.

None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.

This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.

Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.

rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.

Userspace API is not changed.

    text    data     bss      dec     hex filename
30108430 2633624  873672 33615726 200ef6e vmlinux.before.o
30108109 2633612  873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

The CLEARPBA bit in the dynamic interrupt control register actually has
no effect either way on the hardware. As per errata 28 in the XL710
specification update the interrupt is actually cleared any time the
register is written with the INTENA_MSK bit set to 0. As such the act of
toggling the enable bit actually will trigger the interrupt being
cleared and could lead to potential lost events if auto-masking is
not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a further clean-up related to the change over to using
q_vector->reg_idx when accessing the ITR registers. Specifically the code
appears to have several other spots where we were computing the register
offset manually and this resulted in errors in a few spots.

Specifically in the i40evf functions for mapping queues to vectors it
appears we may have had an off by 1 error since (v_idx - 1) for the first
q_vector with an index of 0 would result in us returning -1 if I am not
mistaken.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently in i40e_set_priv_flags we use new_flags to check for the
I40E_FLAG_DISABLE_FW_LLDP flag.  This is an issue for a few a reasons.
DISABLE_FW_LLDP is persistent across reboots/driver reloads.  This means
we need some way to detect if FW LLDP is enabled on init.  We do this by
trying to init_dcb and if it fails with EPERM we know LLDP is disabled
in FW.

This could be a problem on older FW versions or NPAR enabled PFs because
there are situations where the FW could disable LLDP, but they do _not_
support using this flag to change it.  If we do end up in this
situation, the flag will be set, then when the user tries to change any
priv flags, the driver thinks the user is trying to disable FW LLDP on a
FW that doesn't support it and essentially forbids any priv flag
changes.

The fix is simple, instead of checking if this flag is set, we should be
checking if the user is trying to _change_ the flag on unsupported FW
versions.

This patch also adds a comment explaining that the cmpxchg is the point
of no return.  Once we put the new flags into pf->flags we can't back
out.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a warning message when the link-down-on-close flag is
setting on. The warning is printed only on MFP devices
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The logic for dynamic ITR update is confusing at best as there were odd
paths chosen for how to find the rings associated with a given queue based
on the vector index and other inconsistencies throughout the code.

This patch is an attempt to clean up the logic so that we can more easily
understand what is going on. Specifically if there is a Rx or Tx ring that
is enabled in dynamic mode on the q_vector it is allowed to override the
other side of the interrupt moderation. While it isn't correct all this
patch is doing is cleaning up the logic for now so that when we come
through and fix it we can more easily identify that this is wrong.

The other big change made here is that we replace references to:
	vsi->rx_rings[q_vector->v_idx]->itr_setting
with:
	q_vector->rx.ring->itr_setting

The general idea is we can avoid the long pointer chase since just
accessing q_vector->rx.ring is a single pointer access versus having to
chase down vsi->rx_rings, and then finding the pointer in the array, and
finally chasing down the itr_setting from there.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

'bufer' should be 'buffer'
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

except, again, POLLFREE and POLL_BUSY_LOOP.

With this, we finally get to the promised end result:

 - POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
   stray instances of ->poll() still using those will be caught by
   sparse.

 - eventpoll.c and select.c warning-free wrt __poll_t

 - no more kernel-side definitions of POLL... - userland ones are
   visible through the entire kernel (and used pretty much only for
   mangle/demangle)

 - same behavior as after the first series (i.e. sparc et.al. epoll(2)
   working correctly).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more poll annotation updates from Al Viro:
 "This is preparation to solving the problems you've mentioned in the
  original poll series.

  After this series, the kernel is ready for running

      for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
            L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
            for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
      done

  as a for bulk search-and-replace.

  After that, the kernel is ready to apply the patch to unify
  {de,}mangle_poll(), and then get rid of kernel-side POLL... uses
  entirely, and we should be all done with that stuff.

  Basically, that's what you suggested wrt KPOLL..., except that we can
  use EPOLL... instead - they already are arch-independent (and equal to
  what is currently kernel-side POLL...).

  After the preparations (in this series) switch to returning EPOLL...
  from ->poll() instances is completely mechanical and kernel-side
  POLL... can go away. The last step (killing kernel-side POLL... and
  unifying {de,}mangle_poll() has to be done after the
  search-and-replace job, since we need userland-side POLL... for
  unified {de,}mangle_poll(), thus the cherry-pick at the last step.

  After that we will have:

   - POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of
     ->poll() still using those will be caught by sparse.

   - eventpoll.c and select.c warning-free wrt __poll_t

   - no more kernel-side definitions of POLL... - userland ones are
     visible through the entire kernel (and used pretty much only for
     mangle/demangle)

   - same behavior as after the first series (i.e. sparc et.al. epoll(2)
     working correctly)"

* 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  annotate ep_scan_ready_list()
  ep_send_events_proc(): return result via esed->res
  preparation to switching ->poll() to returning EPOLL...
  add EPOLLNVAL, annotate EPOLL... and event_poll->event
  use linux/poll.h instead of asm/poll.h
  xen: fix poll misannotation
  smc: missing poll annotations

Pull xtense fix from Max Filippov:
 "Build fix for xtensa architecture with KASAN enabled"

* tag 'xtensa-20180211' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix build with KASAN

Pull nios2 update from Ley Foon Tan:

 - clean up old Kconfig options from defconfig

 - remove leading 0x and 0s from bindings notation in dts files

* tag 'nios2-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: defconfig: Cleanup from old Kconfig options
  nios2: dts: Remove leading 0x and 0s from bindings notation

The commit 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT
usage") removed KASAN_SHADOW_SCALE_SHIFT definition from
include/linux/kasan.h and added it to architecture-specific headers,
except for xtensa. This broke the xtensa build with KASAN enabled.
Define KASAN_SHADOW_SCALE_SHIFT in arch/xtensa/include/asm/kasan.h

Reported by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage")
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>