Currently memtrace doesn't build if NUMA=n:

  In function ‘memtrace_alloc_node’:
  arch/powerpc/platforms/powernv/memtrace.c:134:6:
  error: the address of ‘contig_page_data’ will always evaluate as ‘true’
    if (!NODE_DATA(nid) || !node_spanned_pages(nid))
        ^

This is because for NUMA=n NODE_DATA(nid) points to an always
allocated structure, contig_page_data.

But even in the NUMA=y case memtrace_alloc_node() is only called for
online nodes, and we should always have a NODE_DATA() allocated for an
online node. So remove the (hopefully) overly paranoid check, which
also means we can build when NUMA=n.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In commit e6a6928c ("of/fdt: Convert FDT functions to use
libfdt") (Apr 2014), the generic flat device tree code dropped support
for flat device tree's older than version 0x10 (16).

We still have code in our CPU scanning to cope with flat device tree
versions earlier than 2, which can now never trigger, so drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add a test of the relative branch patching logic in the alternate
section feature fixup code. This tests that if we branch past the last
instruction of the alternate section, the branch is not patched.
That's because the assembler will have created a branch that already
points to the first instruction after the patched section, which is
correct and needs no further patching.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We want this to remain the last test (because it's disabled by
default), so give it a non-numbered name so we don't have to renumber
it when adding new tests before it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The code patching code has always been a bit confused about whether
it's best to use void *, unsigned int *, char *, etc. to point to
instructions. In fact in the feature fixups tests we use both unsigned
int[] and u8[] in different places.

Unfortunately the tests that use unsigned int[] calculate the size of
the code blocks using subtraction of those unsigned int pointers, and
then pass the result to memcmp(). This means we're only comparing 1/4
of the bytes we need to, because we need to multiply by
sizeof(unsigned int) to get the number of *bytes*.

The result is that the tests do all the patching and then only compare
some of the resulting code, so patching bugs that only effect that
last 3/4 of the code could slip through undetected. It turns out that
hasn't been happening, although one test had a bad expected case (see
previous commit).

Fix it for now by multiplying the size by 4 in the affected functions.

Fixes: 362e7701 ("powerpc: Add self-tests of the feature fixup code")
Epic-brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The expected case for this test was wrong, the source of the alternate
code sequence is:

  FTR_SECTION_ELSE
  2:	or	2,2,2
  	PPC_LCMPI	r3,1
  	beq	3f
  	blt	2b
  	b	3f
  	b	1b
  ALT_FTR_SECTION_END(0, 1)
  3:	or	1,1,1
  	or	2,2,2
  4:	or	3,3,3

So when it's patched the '3' label should still be on the 'or 1,1,1',
and the 4 label is irrelevant and can be removed.

Fixes: 362e7701 ("powerpc: Add self-tests of the feature fixup code")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If the systbl_chk.sh checks fail we print a message, but with no
indication that it's an error. That makes it hard to find in build
logs with eg. grep.

So prefix any output with "Error:".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

it had always been pointless - compat_sys_select() sign-extends
the first argument just fine on its own.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mpe: Use COMPAT_SPU_NEW() to keep systbl_chk.sh happy]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently the select system call is wired up with the SYSX_SPU()
macro. The SYSX_SPU() is not handled by systbl_chk.c, which means the
syscall number for select is not checked.

That hides the fact that the syscall number for select is actually
__NR__newselect not __NR_select.

In a following patch we'd like to drop ppc32_select() which means
select will become a regular COMPAT_SYS_SPU() syscall. But
COMPAT_SYS_SPU() can't deal with the fact that the syscall number is
actually __NR__newselect. We also can't just redefine __NR_select
because that's still used for the old select call.

So add a new COMPAT_NEW_SPU() that does the same thing as
COMPAT_SYS_SPU() except it encodes that we're using the new number.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mpe: Update sys_ni.c for s/ppc_rtas/sys_rtas/]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mpe: Fix sys_debug_setcontext() prototype to return long]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The "Power Architecture 64-Bit ELF V2 ABI" says in section 2.3.2.3:

[...] There are several rules that must be adhered to in order to ensure
reliable and consistent call chain backtracing:

* Before a function calls any other function, it shall establish its
  own stack frame, whose size shall be a multiple of 16 bytes.

 – In instances where a function’s prologue creates a stack frame, the
   back-chain word of the stack frame shall be updated atomically with
   the value of the stack pointer (r1) when a back chain is implemented.
   (This must be supported as default by all ELF V2 ABI-compliant
   environments.)
[...]
 – The function shall save the link register that contains its return
   address in the LR save doubleword of its caller’s stack frame before
   calling another function.

To me this sounds like the equivalent of HAVE_RELIABLE_STACKTRACE.
This patch may be unneccessarily limited to ppc64le, but OTOH the only
user of this flag so far is livepatching, which is only implemented on
PPCs with 64-LE, a.k.a. ELF ABI v2.

Feel free to add other ppc variants, but so far only ppc64le got tested.

This change also implements save_stack_trace_tsk_reliable() for ppc64le
that checks for the above conditions, where possible.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Provide timebase and timebase of last heartbeat in watchdog lockup
messages. Also provide a stack trace of when a CPU becomes un-stuck,
which can be useful -- it could be where irqs are re-enabled, so it
may be the end of the critical section which is responsible for the
latency which is useful information.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The watchdog heartbeat timestamp is updated when the local heartbeat
timer fires (or touch_nmi_watchdog() is called).

This is an interesting data point, so don't overwrite it when the
soft-NMI interrupt detects a hard lockup. That code came from a pre-
merge version to prevent hard lockup messages flood, but that's taken
care of with the stuck CPU logic now, so there is no reason to
update the heartbeat timestamp here.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This is not the case for the moment, but future releases of pHyp might
need to introduce some synchronisation routines under the hood which
would make the XIVE hcalls longer to complete.

As this was done for H_INT_RESET, let's wrap the other hcalls in a
loop catching the H_LONG_BUSY_* codes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The hcall H_INT_RESET should be called to make sure XIVE is fully
reseted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The hcall H_INT_RESET can take some time to complete and in such cases
it returns H_LONG_BUSY_* codes requiring the machine to sleep for a
while before retrying.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The kexec_state KEXEC_STATE_IRQS_OFF barrier is reached by all
secondary CPUs before the kexec_cpu_down() operation is called on
secondaries. This can raise conflicts and provoque errors in the XIVE
hcalls when XIVE is shutdown with H_INT_RESET on the primary CPU.

To synchronize the kexec_cpu_down() operations and make sure the
secondaries have completed their task before the primary starts doing
the same, let's move the primary kexec_cpu_down() after the
KEXEC_STATE_REAL_MODE barrier.

This change of the ending sequence of kexec is mostly useful on the
pseries platform but it impacts also the powernv, ps3 and 85xx
platforms. powernv can be easily tested and fixed but some caution is
required for the other two.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

For consideration:

* Add NVDIMM support - Enables greater testing, mambo device.
* Add IPv6 support built in + additional modules - Because it's 2018 maan.
* Add DEFERRED_STRUCT_PAGE_INIT - Let's see what breaks.
* Add PPC_MEMTRACE - Small powernv debugfs driver for getting hardware traces.
* Add MEMORY_FAILURE - Machine check exceptions can now drive memory failure.
* Turn on FANOTIFY - This is the current filesystem notification feature.
* Turn on SCOM_DEBUGFS - Handy for hardware/firmware debugging, security risk?
* Turn on async SCSI scanning - Let's see what breaks.
* Add MLX5 driver as a module - Popular demand.
* Add CRYPTO_CRCT10DIF_VPMSUM - POWER8 T10DIF acceleration.

* Make a bunch of USB hid drivers modules.
* Make SCSI SG, SR, and FC modules - FC is huge.
* Make video drivers except AST GPU modules - Also huge.
* Make PCI serial driver a module - Uncommon.
* Make more things modules, NFS FS, RAM disk, netconsole, MS-DOS fs.

* Get rid of /dev/port - Not used.
* Remove PPS and PTP subsystms - Unusual.
* Remove legacy BSD ttys - Long dead.
* Remove IDE - Deprecated and replaced with ATA.
* Remove WIRELESS - Until we get POWER9 laptops.
* Remove RAW - Long deprecated in favour of direct IO.
* Remove floppy, parport, and PS2 input devices - not supported.
* Remove virtio drivers, ballooning - We're host only.
* Remove PPP - Sorry Paulus.

This results in a significantly smaller vmlinux:

    text      data       bss        dec   filename
13143383   5277944   1317856   19739183   vanilla
12263281   4852074   1341720   18457075   patched
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The B43 driver only needs CONFIG_SSB to support the WLAN card found in
the Wii. Configure it accordingly, and disable BCMA bus support to save
a bit of space.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This allows access to the SD card and the BCM4318 Wifi module.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Now that there's a GPIO driver for the Wii, let's enable the following
drivers:

- the GPIO driver itself
- gpio-keys
- gpio-poweroff
- gpio-leds and a few LED triggers
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Wii doesn't have built-in Ethernet and USB Ethernet adapters are in
a different menu. Disable CONFIG_ETHERNET to save some space in support
code for Ethernet drivers.

Note that this patch doesn't disable any Ethernet drivers, because they
are not enabled by default.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The hcall_exit() tracepoint has retval defined as unsigned long. That
leads to humours results like:

  bash-3686  [009] d..2   854.134094: hcall_entry: opcode=24
  bash-3686  [009] d..2   854.134095: hcall_exit: opcode=24 retval=18446744073709551609

It's normal for some hcalls to return negative values, displaying them
as unsigned isn't very helpful. So change it to signed.

  bash-3711  [001] d..2   471.691008: hcall_entry: opcode=24
  bash-3711  [001] d..2   471.691008: hcall_exit: opcode=24 retval=-7

Which can be more easily compared to H_NOT_FOUND in hvcall.h
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>

This commit was a stop-gap to prevent crashes on hotunplug, caused by
the mismatch between the 1G mappings used for the linear mapping and the
memory block size. Those issues are now resolved because we split the
linear mapping at hotunplug time if necessary, as implemented in commit
4dd5f8a9 ("powerpc/mm/radix: Split linear mapping on hot-unplug").
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Tested-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

By using IS_ENABLED() we can simplify __set_pte_at() by removing
redundant *ptep = pte.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

_PAGE_BUSY is always 0, remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When nohash and book3s header were split, some hash related stuff
remained in the nohash header. This patch removes them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Duplicate pte_young() to avoid circular header dependency]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Unregister fadump on kexec down path otherwise the fadump registration
in new kexec-ed kernel complains that fadump is already registered.
This makes new kernel to continue using fadump registered by previous
kernel which may lead to invalid vmcore generation. Hence this patch
fixes this issue by un-registering fadump in fadump_cleanup() which is
called during kexec path so that new kernel can register fadump with
new valid values.

Fixes: b500afff ("fadump: Invalidate registration and release reserved memory for general use.")
Cc: stable@vger.kernel.org # v3.4+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

FADump capture kernel boots in restricted memory environment preserving
the context of previous kernel to save vmcore. Supporting hugepages in
such environment makes things unnecessarily complicated, as hugepages
need memory set aside for them. This means most of the capture kernel's
memory is used in supporting hugepages. In most cases, this results in
out-of-memory issues while booting FADump capture kernel. But hugepages
are not of much use in capture kernel whose only job is to save vmcore.
So, disabling hugepages support, when fadump is active, is a reliable
solution for the out of memory issues. Introducing a flag variable to
disable HugeTLB support when fadump is active.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The second kernel, during early boot after the crash, reserves rest of
the memory above boot memory size to make sure it does not touch any of the
dump memory area. It uses memblock_reserve() that reserves the specified
memory region irrespective of memory holes present within that region.
There are chances where previous kernel would have hot removed some of
its memory leaving memory holes behind. In such cases fadump kernel reports
incorrect number of reserved pages through arch_reserved_kernel_pages()
hook causing kernel to hang or panic.

Fix this by excluding memory holes while reserving rest of the memory
above boot memory size during second kernel boot after crash.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

config TRACING_SUPPORT has an exception for PPC32, because PPC32
didn't have irqflags tracing support.

But that hasn't been true since commit 5d38902c ("powerpc: Add
irqtrace support for 32-bit powerpc") (Jun 2009).

So remove the exception for PPC32 and the comment.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

I no longer have a functional version of this board for even the most
basic sanity boot testing, and they have not been available for purchase
for quite some years now.

There is no point in adding a burden to testing coverage that does
walk all the possible defconfigs, so with all the above in mind, it
makes sense to remove it.  Of course it will remain in the git history
for anyone who happens to stumble on one and wants to tinker with it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We've had dynamic ftrace support for over 9 years since Steve first
wrote it, all the distros use dynamic, and static is basically
untested these days, so drop support for static ftrace.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

With -mprofile-kernel, we always save the full register state in
ftrace_caller(). While this works, this is inefficient if we're not
interested in the register state, such as when we're using the function
tracer.

Rename the existing ftrace_caller() as ftrace_regs_caller() and provide
a simpler implementation for ftrace_caller() that is used when registers
are not required to be saved.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Our implementation matches that of the generic version, which also
handles FTRACE_UPDATE_MODIFY_CALL. So, remove our implementation in
favor of the generic version.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

For R_PPC64_REL24 relocations, we suppress emitting instructions for TOC
load/restore in the relocation stub if the relocation is for _mcount()
call when using -mprofile-kernel ABI.

To detect this, we check if the preceding instructions are per the
standard set of instructions emitted by gcc: either the two instruction
sequence of 'mflr r0; std r0,16(r1)', or the more optimized variant of a
single 'mflr r0'. This is not sufficient since nothing prevents users
from hand coding sequences involving a 'mflr r0' followed by a 'bl'.

For removing the toc save instruction from the stub, we additionally
check if the symbol is "_mcount". Add the same check here as well.

Also rename is_early_mcount_callsite() to is_mprofile_mcount_callsite()
since that is what is being checked. The use of "early" is misleading
since there is nothing involving this function that qualifies as early.

Fixes: 15308664 ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>