- 24 Sep, 2013 2 commits
-
-
Duan Jiong authored
Redirect isn't an error condition, it should leave the error handler without touching the socket. Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Duan Jiong authored
Redirect isn't an error condition, it should leave the error handler without touching the socket. Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 23 Sep, 2013 14 commits
-
-
Noel Burton-Krahn authored
MRP doesn't implement the periodictimer in 802.1Q, so it never retries if packets get lost. I ran into this problem when MRP sent a MVRP JoinIn before the interface was fully up. The JoinIn was lost, MRP didn't retry, and MVRP registration failed. Tested against Juniper QFabric switches Signed-off-by: Noel Burton-Krahn <noel@burton-krahn.com> Acked-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
-
josselin.costanzi@mobile-devices.fr authored
Actually re-send packets when the T1 timer runs out. This fixes a bug where packets are waiting on the write queue until disconnection when no other traffic is outstanding. Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr> Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Yuval Mintz says: ==================== This patch contains various bug fixes, half of which are SR-IOV related (some fixing issues in the recently added VF RSS support), while the other fix a wide assortments of issues in the driver. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ariel Elior authored
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of the previous existing messages. If an old VF driver were to send this message to the PF then the PF will not reply and leave the mailbox in an unsteady state (and cause a timeout on the VF side). Wait until firmware ack is written before unlocking channel Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
During flows which mask block attentions (e.g., register dump) all parities are masked. However, unlike other blocks the MCP's attention is not masked inside the block but rather the indication to the driver. If another attention (e.g., link change) will occour while there's an MCP parity, the driver will ignore the fact that the parity is masked and erroneously report a parity. This patch forces the driver to read the MCP masking while checking for parities. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yuval Mintz authored
During error flows while loading cnic the return value was incorrectly replaced by that of bnx2x_set_real_num_queues(); If that function was to finish successfully then the cnic would have mistakenly thought the load ended successfully, causing issues (& panics) later on. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ariel Elior authored
bnx2x_iov_static_resc() should be called after IGU was read for information on the number of available VFs, so that resources will be correctly set. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ariel Elior authored
Due to incorrect usage of PF macros when reading information relating to interrupts, some PFs were erroneously unable to support VFs. Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eilon Greenstein authored
When system CPU is stressed it's possible that the driver will not be able to pulse the FW every second, which will cause the log to be filled with error messages. Increasing the threshold to 5 seconds seems to be enough to eliminate the issue. Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yaniv Rosner authored
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the actual configuration. Change the 848xx duplex settings to advertise half-duplex only if configured. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yaniv Rosner authored
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yaniv Rosner authored
when 1G-optic module was plugged in, internal loopback test failed because the driver used to check the optic module (with no need), and for 1G optic module, the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled. This patch avoid accessing optic module in case internal loopback was selected, and update the link speed in case 1G optic module was detected during init stage. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yaniv Rosner authored
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not configured in order to clear it's configuration, otherwise the link may come up at 20G instead of the requested 10G-KR. In addition, restart AN after disabling KR2 as part of the KR2 work-around. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yaniv Rosner authored
Previously, in case of KR link down, the driver would reset the PHY and restart auto negotiation only when old Warpcore microcode was used (below D108). This patch comes to generalize this by keep trying to restart KR link, regardless of Warpcore microcode, since it was found that it solves another link issue which source is a link-partner. As part of this change, the signal detect is no longer a condition to apply the work-around to cover this new case. Like before, as long as the link is down, AN will be restarted every 2 seconds. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 21 Sep, 2013 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfcDavid S. Miller authored
Ben Hutchings says: ==================== Daniel Pieczko fixed two bugs in reset handling that particularly affected the new SFC9120 controller. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 20 Sep, 2013 10 commits
-
-
Andre Naujoks authored
The old implementation was heavy on str* functions and sprintf calls. This version is more manual, but faster. Profiling just the printing of a 3 char CAN-id resulted in 60 instructions for the manual method and over 2000 for the sprintf method. Bear in mind the profiling was done against libc and not the kernel sprintf. Together with this rewrite an issue with sending and receiving of RTR frames has been fixed by Oliver for the cases that the DLC is not zero. Signed-off-by: Andre Naujoks <nautsch2@gmail.com> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andre Naujoks authored
To be able to use the hex ascii functions in case sensitive environments the array hex_asc_upper[] and the needed functions for hex_byte_pack_upper() are introduced. Signed-off-by: Andre Naujoks <nautsch2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andre Naujoks authored
The locking is needed, since the the internal buffer for the CAN frames is changed during the wakeup call. This could cause buffer inconsistencies under high loads, especially for the outgoing short CAN packet skbuffs. The needed locks led to deadlocks before commit "5ede5253 tty: Remove extra wakeup from pty write() path", which removed the direct callback to the wakeup function from the tty layer. As slcan.c is based on slip.c the issue in the original code is fixed, too. Signed-off-by: Andre Naujoks <nautsch2@gmail.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Daniel Pieczko authored
The SFC9120 MC firmware often takes longer than 20ms to reboot and update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of 250ms is very generous for an MC reboot. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
-
Daniel Pieczko authored
Scheduling a reset following an MC reboot event before waiting for reboot to complete results in a race that can lead to a state where must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have been destroyed during the MC reboot. To avoid MC errors when trying to remove VIs that do not exist, wait for the MC reboot to complete before scheduling the reset. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64Linus Torvalds authored
Pull ARM64 fixes from Catalin Marinas: - Compat register fault reporting fix - Documentation clarification on tagged pointers - hwcap widened to 64-bit (user space already reading it as 64-bit) * tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: arm64: Widen hwcap to be 64 bit arm64: Correctly report LR and SP for compat tasks arm64: documentation: tighten up tagged pointer documentation arm64: Make do_bad_area() function static
-
Steve Capper authored
Under arm64 elf_hwcap is a 32 bit quantity, but it is stored in a 64 bit auxiliary ELF field and glibc reads hwcap as 64 bit. This patch widens elf_hwcap to be 64 bit. Signed-off-by: Steve Capper <steve.capper@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
-
Catalin Marinas authored
When a task crashes and we print debugging information, ensure that compat tasks show the actual AArch32 LR and SP registers rather than the AArch64 ones. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
-
Will Deacon authored
Commit d50240a5 ("arm64: mm: permit use of tagged pointers at EL0") added support for tagged pointers in userspace, but the corresponding update to Documentation/ contained some imprecise statements. This patch fixes up some minor ambiguities in the text, hopefully making it more clear about exactly what the kernel expects from user virtual addresses. Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
-
Catalin Marinas authored
This function is only called from arch/arm64/mm/fault.c. Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
-
- 19 Sep, 2013 13 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "A set of fixes for ARM platforms for 3.12. Among them: - A fix for build breakage in the MTD subsystem for some PXA devices. David Woodhouse has this patch in his for-next branch but has not been responding to our requests to send it up so here it is. I should have amended the commit message to describe the build failure for CONFIG_OF=n setups, but forgot and now it's down in the stack of commits. - Added device-tree for the BeagleBone Black. Turns out people have been using the older "regualar" bone DT for the newer boards, and there's risk of damaging hardware that way. - Misc DT and regular fixes for OMAP. - Fix to make the ST-Ericsson "snowball" boards boot with multi_v7_defconfig, and enable one of the ST-E reference boards on the same config. - Kconfig cleanup for u300 to hide submenus when the platform isn't enabled. - Enable ARM_ATAG_DTB_COMPAT to let firmware override command line when booting with an appended devicetree on non-DT-enabled firmware (needed to boot snowball)" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits) ARM: multi_v7: add HREFv60 to multi_v7 defconfig ARM: OMAP2+: mux: fix trivial typo in name ARM: OMAP4 SMP: Corrected a typo fucntions to functions ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionally mailbox: remove unnecessary platform_set_drvdata() ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=y ARM: OMAP: fix return value check in omap_device_build_from_dt() ARM: OMAP4: Fix clock_get error for GPMC during boot ARM: sa1100: collie.c: fall back to jedec_probe flash detection ARM: u300: hide submenus ARM: dts: igep00x0: Add pinmux configuration for MCBSP2 ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard mtd: nand: pxa3xx: Remove unneeded ifdef CONFIG_OF ARM: multi_v7_defconfig: enable ARM_ATAG_DTB_COMPAT ARM: ux500: disable outer cache debug ARM: dts: OMAP5: fix ocp2scp DTS data ARM: dts: OMAP5: fix reg property size ARM: dts: am335x-bone*: add DT for BeagleBone Black ARM: dts: omap3-beagle-xm: fix string error in compatible property ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) If the local_df boolean is set on an SKB we have to allocate a unique ID even if IP_DF is set in the ipv4 headers, from Ansis Atteka. 2) Some fixups for the new chipset support that went into the sfc driver, from Ben Hutchings. 3) Because SCTP bypasses a good chunk of, and actually duplicates, the logic of the ipv6 output path, some IPSEC things don't get done properly. Integrate SCTP better into the ipv6 output path so that these problems are fixed and such issues don't get missed in the future either. From Daniel Borkmann. 4) Fix skge regressions added by the DMA mapping error return checking added in v3.10, from Mikulas Patocka. 5) Kill some more IRQF_DISABLED references, from Michael Opdenacker. 6) Fix races and deadlocks in the bridging code, from Hong Zhiguo. 7) Fix error handling in tun_set_iff(), in particular don't leak resources. From Jason Wang. 8) Prevent format-string injection into xen-netback driver, from Kees Cook. 9) Fix regression added to netpoll ARP packet handling, in particular check for the right ETH_P_ARP protocol code. From Sonic Zhang. 10) Try to deal with AMD IOMMU errors when using r8169 chips, from Francois Romieu. 11) Cure freezes due to recent changes in the rt2x00 wireless driver, from Stanislaw Gruszka. 12) Don't do SPI transfers (which can sleep) in interrupt context in cw1200 driver, from Solomon Peachy. 13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719. From Nithin Sujir. 14) Make xen_netbk_count_skb_slots() count the actual number of slots that will be used, taking into consideration packing and other issues that the transmit path will run into. From David Vrabel. 15) Use the correct maximum age when calculating the bridge message_age_timer, from Chris Healy. 16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey Khoroshilov. 17) Netfilter conntrack extensions were converted to RCU but are not always freed properly using kfree_rcu(). Fix from Michal Kubecek. 18) VF reset recovery not being done correctly in qlcnic driver, from Manish Chopra. 19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko. 20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang. 21) Internal switch not initialized properly in bgmac driver, from Rafał Miłecki. 22) Netlink messages report wrong local and remote addresses in IPv6 tunneling, from Ding Zhi. 23) ICMP redirects should not generate socket errors in DCCP and SCTP. We're still working out how this should be handled for RAW and UDP sockets. From Daniel Borkmann and Duan Jiong. 24) We've had several bugs wherein the network namespace's loopback device gets accessed after it is free'd, NULL it out so that we can catch these problems more readily. From Eric W Biederman. 25) Fix regression in TCP RTO calculations, from Neal Cardwell. 26) Fix too early free of xen-netback network device when VIFs still exist. From Paul Durrant. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits) netconsole: fix a deadlock with rtnl and netconsole's mutex netpoll: fix NULL pointer dereference in netpoll_cleanup skge: fix broken driver ip: generate unique IP identificator if local fragmentation is allowed ip: use ip_hdr() in __ip_make_skb() to retrieve IP header xen-netback: Don't destroy the netdev until the vif is shut down net:dccp: do not report ICMP redirects to user space cnic: Fix crash in cnic_bnx2x_service_kcq() bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions. vxlan: Avoid creating fdb entry with NULL destination tcp: fix RTO calculated from cached RTT drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h> net loopback: Set loopback_dev to NULL when freed batman-adv: set the TAG flag for the vid passed to BLA netfilter: nfnetlink_queue: use network skb for sequence adjustment net: sctp: rfc4443: do not report ICMP redirects to user space net: usb: cdc_ether: use usb.h macros whenever possible net: usb: cdc_ether: fix checkpatch errors and warnings net: usb: cdc_ether: Use wwan interface for Telit modules ip6_tunnels: raddr and laddr are inverted in nl msg ...
-
Nikolay Aleksandrov authored
This bug was introduced by commit 7a163bfb ("netconsole: avoid a crash with multiple sysfs writers"). In store_enabled() we have the following sequence: acquire nt->mutex then rtnl, but in the netconsole netdev notifier we have rtnl then nt->mutex effectively leading to a deadlock. The NULL pointer dereference that the above commit tries to fix is actually due to another bug in netpoll_cleanup(). This is fixed by dropping the mutex from the netdev notifier as it's already protected by rtnl. Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikolay Aleksandrov authored
I've been hitting a NULL ptr deref while using netconsole because the np->dev check and the pointer manipulation in netpoll_cleanup are done without rtnl and the following sequence happens when having a netconsole over a vlan and we remove the vlan while disabling the netconsole: CPU 1 CPU2 removes vlan and calls the notifier enters store_enabled(), calls netdev_cleanup which checks np->dev and then waits for rtnl executes the netconsole netdev release notifier making np->dev == NULL and releases rtnl continues to dereference a member of np->dev which at this point is == NULL Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Mikulas Patocka authored
The patch 136d8f37 broke the skge driver. Note this part of the patch: + if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) { + dev_kfree_skb(nskb); + goto resubmit; + } + pci_unmap_single(skge->hw->pdev, dma_unmap_addr(e, mapaddr), dma_unmap_len(e, maplen), PCI_DMA_FROMDEVICE); skb = e->skb; prefetch(skb->data); - skge_rx_setup(skge, e, nskb, skge->rx_buf_size); The function skge_rx_setup modifies e->skb to point to the new skb. Thus, after this change, the new buffer, not the old, is returned to the networking stack. This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should be queued for 3.11-stable. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reported-by: Mikulas Patocka <mpatocka@redhat.com> Reported-by: Vasiliy Glazov <vascom2@gmail.com> Tested-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ansis Atteka authored
If local fragmentation is allowed, then ip_select_ident() and ip_select_ident_more() need to generate unique IDs to ensure correct defragmentation on the peer. For example, if IPsec (tunnel mode) has to encrypt large skbs that have local_df bit set, then all IP fragments that belonged to different ESP datagrams would have used the same identificator. If one of these IP fragments would get lost or reordered, then peer could possibly stitch together wrong IP fragments that did not belong to the same datagram. This would lead to a packet loss or data corruption. Signed-off-by: Ansis Atteka <aatteka@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ansis Atteka authored
skb->data already points to IP header, but for the sake of consistency we can also use ip_hdr() to retrieve it. Signed-off-by: Ansis Atteka <aatteka@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Paul Durrant authored
Without this patch, if a frontend cycles through states Closing and Closed (which Windows frontends need to do) then the netdev will be destroyed and requires re-invocation of hotplug scripts to restore state before the frontend can move to Connected. Thus when udev is not in use the backend gets stuck in InitWait. With this patch, the netdev is left alone whilst the backend is still online and is only de-registered and freed just prior to destroying the vif (which is also nicely symmetrical with the netdev allocation and registration being done during probe) so no re-invocation of hotplug scripts is required. Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS updates from Ralf Baechle: - Minor updates and fixes to the Octeon ethernet driver in staging - A fix to VGA_MAP_MEM() for 64 bit platforms - Fix a workaround for 74K/1074K processors - The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a a file with a name ending in \n. I think this may have been caused by a git bug with with patches sent by email - A build fix for VGA console on BCM1480-based systems - Fix PCI device access via "/sys/bus/pci/.../resource0" or similar work for Alchemy platforms - Fix potential data leak on MIPS R5 cores. This doesn't add proper support for any R5 features, just ensures a kernel without such support will be secure to run - Adding a macros for the CP0 Config5 register to be used by the R5 fix - Make get_cycles() actually return something useful where possible This also requires a preparatory patch for performance sake - Fix a warning about the use of smp_processor_id() in preemptible code. Again this includes a preparatory patch adding the infrastructure to be used by the actual patch - Finally remove pointless one-line comment * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: Fix invalid symbolic link file MIPS: PCI: pci-bcm1480: Include missing vt.h header MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs. MIPS: Add MIPS R5 config5 register. MIPS: PCI: Use pci_resource_to_user to map pci memory space properly MIPS: 74K/1074K: Correct erratum workaround. MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks MIPS: Remove useless comment about kprobe from arch/mips/Makefile MIPS: Fix VGA_MAP_MEM macro. MIPS: Reimplement get_cycles(). MIPS: Optimize current_cpu_type() for better code. MIPS: Fix accessing to per-cpu data when flushing the cache MIPS: Provide nice way to access boot CPU's data. staging: octeon-ethernet: rgmii: enable interrupts that we can handle staging: octeon-ethernet: remove skb alloc failure warnings staging: octeon-ethernet: make dropped packets to consume NAPI budget
-
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-clientLinus Torvalds authored
Pull ceph fixes from Sage Weil: "These fix several bugs with RBD from 3.11 that didn't get tested in time for the merge window: some error handling, a use-after-free, and a sequencing issue when unmapping and image races with a notify operation. There is also a patch fixing a problem with the new ceph + fscache code that just went in" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: fscache: check consistency does not decrement refcount rbd: fix error handling from rbd_snap_name() rbd: ignore unmapped snapshots that no longer exist rbd: fix use-after free of rbd_dev->disk rbd: make rbd_obj_notify_ack() synchronous rbd: complete notifies before cleaning up osd_client and rbd_dev libceph: add function to ensure notifies are complete
-
Madhavan Srinivasan authored
Commit 3b29aa5b [MIPS: add <dt-bindings/> symlink] created a symlink file in include/dt-bindings. Even though commit diff is fine, the symlink is invalid and ls -lb shows a newline character at the end of the filename: lrwxrwxrwx 1 maddy maddy 35 Sep 19 18:11 dt-bindings -> ../../../../../include/dt-bindings\n Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Cc: steven.hill@imgtec.com Cc: mmarek@suse.cz Cc: swarren@nvidia.com Cc: linux-mips@linux-mips.org Cc: linux-kbuild@vger.kernel.org Cc: james.hogan@imgtec.com Patchwork: https://patchwork.linux-mips.org/patch/5859/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Markos Chandras authored
It's needed for the MAX_NR_CONSOLES macro. Fixes the following build problem on a randconfig: arch/mips/pci/pci-bcm1480.c: In function 'bcm1480_pcibios_init': arch/mips/pci/pci-bcm1480.c:261:36: error: 'MAX_NR_CONSOLES' undeclared (first use in this function) arch/mips/pci/pci-bcm1480.c:261:36: note: each undeclared identifier is reported only once for each function it appears in make[1]: *** [arch/mips/pci/pci-bcm1480.o] Error 1 Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5858/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
Currently the kernel will always use the FR=0 register model for O32. If an O32 application did enable FR=1 mode, some data from another application might be leaked in the extra registers becoming visible. Iow, this patch is meant to make the kernel MIPS R5 tolerant but leaves proper MIPS R5 support to a future patchset. Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-