- 21 Mar, 2018 32 commits
-
-
Sean Young authored
Meson doesn't seem to be able to generate timeout events in hardware. So install a software timer to generate the timeout events required by the decoders to prevent "ghost keypresses". Reported-by:
Matthias Reichl <hias@horus.com> Tested-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Johan Hovold authored
Drop bogus call to usb_driver_release_interface() from the disconnect() callback. As the interface is already being unbound at this point, usb_driver_release_interface() simply returns early. Signed-off-by:
Johan Hovold <johan@kernel.org> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Philipp Zabel authored
The IPUv3 code has 8-bit grayscale capture support. Enable imx-media to use it. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Jean-Michel Hautbois authored
The ADV7604 has thirteen 256-byte maps that can be accessed via the main I2C ports. Each map has it own I2C address and acts as a standard slave device on the I2C bus. Allow a device tree node to override the default addresses so that address conflicts with other devices on the same bus may be resolved at the board description level. [Kieran: Re-adapted for mainline] Signed-off-by:
Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com> Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Jean-Michel Hautbois authored
The ADV7604 has thirteen 256-byte maps that can be accessed via the main I2C ports. Each map has it own I2C address and acts as a standard slave device on the I2C bus. Extend the device tree node bindings to be able to override the default addresses so that address conflicts with other devices on the same bus may be resolved at the board description level. [Kieran: Re-adapted for mainline] Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
-
Kieran Bingham authored
The ADV748x has twelve 256-byte maps that can be accessed via the main I2C ports. Each map has it own I2C address and acts as a standard slave device on the I2C bus. Allow a device tree node to override the default addresses so that address conflicts with other devices on the same bus may be resolved at the board description level. Signed-off-by:
Kieran Bingham <kieran.bingham@ideasonboard.com> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Kieran Bingham authored
The ADV748x has 12 pages mapped onto I2C addresses. In the existing implementation only 11 are mapped correctly in the page enumerations, which causes an off-by-one fault on pages above the infoframe definition due to a missing 'CBUS' page. This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly programmed during the iterations in adv748x_initialise_clients(). Until now this has gone un-noticed due to the fact that following the creation of the clients - the device is reset and the addresses are reprogrammed in manually by the call to "adv748x_write_regs(state, adv748x_set_slave_address);" As part of moving to dynamic i2c address allocations repair this by providing the missing CBUS page definition. Signed-off-by:
-
Kieran Bingham authored
The ADV748x has identical map configurations for each register map. The duplication of each map can be simplified using a helper macro such that each map is represented on a single line. Define ADV748X_REGMAP_CONF for this purpose use it to create the tables. Signed-off-by:
-
Hans Verkuil authored
The v4l2_subdev core s_power op was used for two different things: power on/off sensors or video decoders/encoders and to put a tuner in standby (and only the tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner is accessed. The danger with calling (s_power, 0) to put a tuner into standby is that it is usually broadcast for all subdevs. So a video receiver subdev that supports s_power will also be powered off, and since there is no corresponding (s_power, 1) they will never be powered on again. In addition, this is specifically meant for tuners only since they draw the most current. This patch adds a new tuner op called 'standby' and replaces all calls to (core, s_power, 0) by (tuner, standby). This prevents confusion between the two uses of s_power. Note that there is no overlap: bridge drivers either just want to put the tuner into standby, or they deal with powering on/off sensors. Never both. This also makes it easier to replace s_power for the remaining bridge drivers with some PM code later. Whether we want something cleaner for tuners in the future is a separate topic. There is a lot of legacy code surrounding tuners, and I am very hesitant about making changes there. Signed-off-by:
-
Luca Ceresoli authored
Driver writers can benefit in knowing if/when callbacks are called in interrupt context. But it is not completely obvious here, so document it. Signed-off-by:
Luca Ceresoli <luca@lucaceresoli.net> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Pawel Osciak <pawel@osciak.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by:
-
Luca Ceresoli authored
VB2_BUF_STATE_REQUEUEING is accepted by vb2_buffer_done() but not documented, so add it along with notes about calls in interrupt context. Signed-off-by:
-
Luca Ceresoli authored
Documentation about what start_streaming() should do on failure are scattered in two places and mostly duplicated, so consolidate them in one of the two places. Signed-off-by:
-
Douglas Fischer authored
Fixed si470x_start() disabling the interrupt signal, causing tune operations to never complete. This does not affect USB radios because they poll the registers instead of using the IRQ line. Signed-off-by:
Douglas Fischer <fischerdouglasc@gmail.com> [hans.verkuil@cisco.com: fixed 80 column checkpatch warning] Signed-off-by:
-
Douglas Fischer authored
Added the call to v4l2_device_register() required to add a new radio device. Without this patch, it is impossible for the driver to load. This does not affect USB devices. Signed-off-by:
-
Douglas Fischer authored
Fixed si470x_set_channel() trying to tune before chip is turned on, which causes warnings in dmesg and when probing, makes driver wait for 3s for tuning timeout. This issue did not affect USB devices because they have a different probing sequence. Signed-off-by:
-
Hugues Fruchet authored
Add DCMI JPEG support. Signed-off-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Hugues Fruchet authored
Fix unnecessary parentheses in if conditions. Detected by checkpatch.pl --strict. Signed-off-by:
-
Hugues Fruchet authored
Do not stop/restart dma on overrun or errors. Dma will be restarted on current frame transfer completion. Frame transfer completion is ensured even if overrun or error occurs by DCMI continuous capture mode which restarts data transfer at next frame sync. Do no warn on overrun while in irq thread, this slows down system and lead to more overrun errors. Use a counter instead and log errors at stop streaming. Signed-off-by:
-
Hugues Fruchet authored
Fix lock scheme leading to spurious freeze. Signed-off-by:
-
Sakari Ailus authored
v4l2_find_nearest_format is not useful for drivers in finding the best matching format as it assumes a V4L2 specific struct. Drivers will use v4l2_find_nearest_size instead. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Sakari Ailus authored
Use v4l2_find_nearest_size instead of a driver specific function to find nearest matching size. Signed-off-by:
-
Sakari Ailus authored
Use v4l2_find_nearest_size instead of a driver specific function to find nearest matching size. Signed-off-by:
-
Sakari Ailus authored
Use v4l2_find_nearest_size instead of a driver specific function to find nearest matching size. Signed-off-by:
-
Sakari Ailus authored
Add a function (as well as a helper macro) to obtain the best size in a list of device specific sizes. This helps writing drivers as well as aligns interface behaviour across drivers. The struct in which this information is contained in is typically specific to the driver, therefore the existing function v4l2_find_nearest_format() does not address the need. Signed-off-by:
-
Sean Young authored
This renames the protocol for the imon rc driver from other to imon, since it is now an known protocol. Although different name will show up in the sysfs protocol file, loading a keymap using existing ir-keytable versions still works. Signed-off-by:
-
Sean Young authored
This makes it possible to use the various iMON remotes with any raw IR RC device. Signed-off-by:
-
Sean Young authored
If there is IR in the raw kfifo when ir_raw_event_unregister() is called, then kthread_stop() causes ir_raw_event_thread to be scheduled, decode some scancodes and re-arm timer_keyup. The timer_keyup then fires when the rc device is long gone. Cc: stable@vger.kernel.org Signed-off-by:
-
Sean Young authored
These devices were supported by the lirc_imon.c driver which was removed from staging in commit f41003a2 ("[media] staging: lirc_imon: port remaining usb ids to imon and remove"). Signed-off-by:
-
Sean Young authored
Note that the stick on the remote is not supported yet. Signed-off-by:
-
Sean Young authored
This code was ported without the necessary hardware to test. There are multiple problems which are more easily solved by writing a separate driver. This reverts commit f41003a2. Signed-off-by:
-
Philipp Rossak authored
This patch updates documentation for Device-Tree bindings for sunxi IR controller and adds the new optional property for the base clock frequency. Signed-off-by:
Philipp Rossak <embed3d@gmail.com> Acked-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by:
-
Philipp Rossak authored
This patch updates the sunxi-ir driver to set the base clock frequency from devicetree. This is necessary since there are different ir receivers on the market, that operate with different frequencies. So this value could be set if the attached ir receiver needs a different base clock frequency, than the default 8 MHz. Signed-off-by:
Andi Shyti <andi.shyti@samsung.com> Signed-off-by:
-
- 08 Mar, 2018 8 commits
-
-
Dan Carpenter authored
There is a double sizeof() typo here so we don't duplicate the struct properly. Fixes: be7fd3c3 ("media: em28xx: Hauppauge DualHD second tuner functionality") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com>
-
Daniel Scheller authored
Like in ddbridge, get rid of all duplicated I2C client handling constructs and rather make use of the newly added dvb_module_*() helpers. Makes things more clean and removes the (cosmetic) need for some variables. The check on a valid ptr on ci->en isn't really needed since the cxd2099 driver will set it at a time where it is going to return successfully from probing. Signed-off-by:
Daniel Scheller <d.scheller@gmx.net> Signed-off-by:
-
Daniel Scheller authored
Instead of keeping duplicated I2C client handling construct, make use of the newly introduced dvb_module_*() helpers. This not only keeps things way cleaner and removes the need for duplicated I2C client attach code, but even allows to get rid of some variables that won't help in making things look cleaner anymore. The check on a valid ptr on port->en isn't really needed since the cxd2099 driver will set it at a time where it is going to return successfully from probing. Signed-off-by:
-
Daniel Scheller authored
The CIMaX SP2 driver is a EN50221 CI controller I2C driver similar to the cxd2099 driver. Move it's Kconfig block into the newly introduced CI subsection. Cc: Olli Salonen <olli.salonen@iki.fi> Cc: Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Daniel Scheller authored
The cxd2099 driver makes use of the Regmap I2C kernel API, thus add "select REGMAP_I2C" to it's Kconfig block. Also, make it default "m" if !MEDIA_SUBDRV_AUTOSELECT, just like every other dvb-frontend driver. And, while at it, remove the hyphens around the help tag. Cc: Jasmin Jessich <jasmin@anw.at> Signed-off-by:
-
Mauro Carvalho Chehab authored
If I2C is present and it is module, the DVB core should also be a module, otherwise build will now fail with: drivers/media/dvb-core/dvbdev.o: In function `dvb_module_probe': drivers/media/dvb-core/dvbdev.c:965: undefined reference to `i2c_new_device' drivers/media/dvb-core/dvbdev.c:972: undefined reference to `i2c_unregister_device' Reported-by:kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
There's a comment there at s82168 that it is wrong. With firmware 4.0.11, sleep/resume works well without need of download it every time. But firmware 4.0.19 needs to be downloaded again after sleep. Signed-off-by: -
Mauro Carvalho Chehab authored
There are several undocumented v4l2-subdev functions that are part of kAPI. Document them. Acked-by:
-
