- 13 May, 2016 40 commits
-
-
Joshua Henderson authored
Add support for the watchdog peripheral found on PIC32 class devices. Signed-off-by:
Joshua Henderson <joshua.henderson@microchip.com> Signed-off-by:
Purna Chandra Mandal <purna.mandal@microchip.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org Cc: linux-watchdog@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12701/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org>
-
Joshua Henderson authored
Document the devicetree bindings for the watchdog peripheral found on Microchip PIC32 SoC class devices. Signed-off-by:
Rob Herring <robh@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: devicetree@vger.kernel.org Cc: linux-watchdog@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12700/Signed-off-by:
-
Andrzej Hajda authored
IS_ERR_VALUE macro should be used only with unsigned long type. Specifically it works incorrectly with longer types. The patch follows conclusion from discussion on LKML [1][2]. [1]: http://permalink.gmane.org/gmane.linux.kernel/2120927 [2]: http://permalink.gmane.org/gmane.linux.kernel/2150581 [ralf@linux-mips.org: While it may not immediately be obvious, the type of st_value in the end is an unsigned long equivalent so the invocation of IS_ERR_VALUE() was valid but I'm applying the patch anyway for clarity.] Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12553/Signed-off-by:
-
Maciej W. Rozycki authored
Propagate sNaN payload in quieting in the legacy-NaN mode as well. If clearing the quiet bit would produce infinity, then set the next lower trailing significand field bit, matching the SB-1 and BMIPS5000 hardware implementations. Some other MIPS FPU hardware implementations do produce the default qNaN bit pattern instead. This reverts some changes made for semantics preservation with commit dc3ddf42 [MIPS: math-emu: Update sNaN quieting handlers], consequently bringing back most of the semantics from before commit fdffbafb [Lots of FPU bug fixes from Kjeld Borch Egevang.], except from the qNaN produced in the infinity case. Previously the default qNaN bit pattern was produced in that case. Signed-off-by:
Maciej W. Rozycki <macro@imgtec.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/11483/Signed-off-by:
-
Maciej W. Rozycki authored
Update the ELF personality macros used for individual ABIs to make actions in the same order across all of them and match formatting too. Signed-off-by:
-
James Hogan authored
Since commit 8cb48fe1 ("MIPS: Provide correct siginfo_t.si_stime"), MIPS' uapi/asm/siginfo.h has included uapi/asm-generic/siginfo.h directly before defining MIPS' struct siginfo, in order to get the necessary definitions needed for the siginfo struct without the generic copy_siginfo() hitting compiler errors due to struct siginfo not yet being defined. Now that the generic copy_siginfo() is moved out to linux/signal.h we can safely include asm-generic/siginfo.h before defining the MIPS specific struct siginfo, which avoids the uapi/ include as well as breakage due to generic copy_siginfo() being defined before struct siginfo. Reported-by:
Christopher Ferris <cferris@google.com> Fixes: 8cb48fe1 ("MIPS: Provide correct siginfo_t.si_stime") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Petr Malat <oss@malat.biz> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.0- Signed-off-by:
-
James Hogan authored
The generic copy_siginfo() is currently defined in asm-generic/siginfo.h, after including uapi/asm-generic/siginfo.h which defines the generic struct siginfo. However this makes it awkward for an architecture to use it if it has to define its own struct siginfo (e.g. MIPS and potentially IA64), since it means that asm-generic/siginfo.h can only be included after defining the arch-specific siginfo, which may be problematic if the arch-specific definition needs definitions from uapi/asm-generic/siginfo.h. It is possible to work around this by first including uapi/asm-generic/siginfo.h to get the constants before defining the arch-specific siginfo, and include asm-generic/siginfo.h after. However uapi headers can't be included by other uapi headers, so that first include has to be in an ifdef __kernel__, with the non __kernel__ case including the non-UAPI header instead. Instead of that mess, move the generic copy_siginfo() definition into linux/signal.h, which allows an arch-specific uapi/asm/siginfo.h to include asm-generic/siginfo.h and define the arch-specific siginfo, and for the generic copy_siginfo() to see that arch-specific definition. Signed-off-by:
-
Yang Shi authored
octeon_smp_setup and octeon_prepare_cpus are just used during initialization period, so mark them as __init. And, octeon_prepare_cpus is just used in smp.c, so make it static as well. Signed-off-by:
Yang Shi <yang.shi@windriver.com> Cc: david.daney@cavium.com Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12574/Signed-off-by:
-
Álvaro Fernández Rojas authored
- Remove unneeded leds0 alias. - Switch to bcm6345-l1-intc interrupt controller. - Use interrupt-controller instead of periph_intc and cpu_intc. - Add uart1 node. - Single ohci and ehci nodes. - Avoid using underscores in node names. - Rename uart aliases to serial. - Remove blank line in cpus node. [ralf@linux-mips.org: fix references in bcm96368mvwg.dts so the file keeps building.] Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> Cc: f.fainelli@gmail.com Cc: jogo@openwrt.org Cc: cernekee@gmail.com Cc: robh@kernel.org Cc: simon@fire.lp0.eu Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by:
-
Álvaro Fernández Rojas authored
- Remove unneeded leds0 alias. - Switch to bcm6345-l1-intc interrupt controller. - Use interrupt-controller instead of periph_intc and cpu_intc. - Add uart1, ehci and ohci nodes. - Refactor syscon and syscon-reboot. - Avoid using underscores in node names. - Rename uart aliases to serial. Signed-off-by:
-
Álvaro Fernández Rojas authored
This SoC is very similar to BCM63168 and Broadcom usually refers to them as BCM63268. Add BCM63268 and missing BCM63168 to device tree documentation. Signed-off-by:
-
Álvaro Fernández Rojas authored
This adds a device tree example for SFR Neufbox4 (Sercomm version), which also serves as a real example for brcm,bcm6358-leds. Signed-off-by:
-
Álvaro Fernández Rojas authored
BCM6358 has a shared TLB which conflicts with current SMP support, so it must be disabled for now. BCM6358 uses >= 0xfffe0000 addresses for internal registers, which need to be remapped (by using a simplified version of BRCM63xx ioremap.h). However, 0xfff80000 is a better address, since it also covers BCM3368, leaving the possibility to add it in the future. Signed-off-by:
-
Kelvin Cheung authored
This patch replaces goto out with return in ls1x_cpufreq_probe(). Signed-off-by:
Kelvin Cheung <keguang.zhang@gmail.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: linux-pm@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13056/Signed-off-by:
-
Kelvin Cheung authored
This patch uses devm_kzalloc() instead of global structure. Signed-off-by:
-
Kelvin Cheung authored
This patch uses dev_get_platdata() to get the platform_data instead of referencing it directly. Signed-off-by:
-
Kelvin Cheung authored
This patch replaces kzalloc() with kcalloc() when allocating frequency table, and remove unnecessary 'out of memory' message. Signed-off-by:
-
Kelvin Cheung authored
This patch renames the file to loongson1-cpufreq.c, and also includes some minor updates. Signed-off-by:
-
Florian Fainelli authored
Just to ease debugging of multiplatform kernel, make sure we print "Broadcom BMIPS5200" for the BMIPS5200 implementation instead of Broadcom BMIPS5000. Fixes: 68e6a783 ("MIPS: BMIPS: Add PRId for BMIPS5200 (Whirlwind)") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13014/Signed-off-by:
-
Florian Fainelli authored
BMIPS_GENERIC being multiplatform and intended to support BMIPS3200, BMIPS3300, BMIPS4350, BMIPS4380 and BMIPS5000-class processors, there is not much more we can put in there since they do not share the same I and D cache line sizes at all (doubled for every new generation essentially), some processors have a S-cache, some don't, some have a FPU, some don't. Signed-off-by:
-
Florian Fainelli authored
local_r4k___flush_cache_all() is missing a special check for BMIPS5000 processors, we need to blast the S-cache, just like other MTI processors since we have an inclusive cache. We also need an additional __sync() to make sure this is completed. Fixes: d74b0172 ("MIPS: BMIPS: Add special cache handling in c-r4k.c") Signed-off-by:
-
Florian Fainelli authored
BMIPS5000 and BMIPS5200 processor have no D cache aliases, and this is properly handled by the per-CPU override added at the end of r4k_cache_init(), the problem is that the output of probe_pcache() disagrees with that, since this is too late: Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes With the change moved earlier, we now have a consistent output with the settings we are intending to have: Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes. Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes Fixes: d74b0172 ("MIPS: BMIPS: Add special cache handling in c-r4k.c") Signed-off-by:
-
Florian Fainelli authored
BMIPS5000 and BMIPS52000 processors have their I-cache filling from the D-cache. Since BMIPS_GENERIC does not provide (yet) a cpu-feature-overrides.h file, this was not set anywhere, so make sure the R4K cache detection takes care of that. Fixes: d74b0172 ("MIPS: BMIPS: Add special cache handling in c-r4k.c") Signed-off-by:
-
Florian Fainelli authored
Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bmips_be_defconfig since this is a necessary option to parse the built-in flash partition table on BMIPS big-endian SoCs (Cable Modem and DSL). Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Cc: cernekee@gmail.com Cc: jogo@openwrt.org Cc: simon@fire.lp0.eu Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12256/Signed-off-by:
-
Florian Fainelli authored
Enable CONFIG_MTD_BCM63XX_PARTS in arch/mips/configs/bcm63xx_defconfig since this is a necessary option to parse the built-in flash partition table on BCM63xx SoCs. Signed-off-by:
-
Kelvin Cheung authored
This patch adds Loongson1 architecture entry. Signed-off-by:
-
Kelvin Cheung authored
- Add DMA device - Add NAND device - Add GPIO device - Add LED device - Update the defconfig and rename it to loongson1b_defconfig - Fix ioremap size - Other minor fixes Signed-off-by:
-
Maciej W. Rozycki authored
... making upstream development binutils snapshots work as expected, e.g.: $ mips64el-linux-ld --version GNU ld (GNU Binutils) 2.20.1.20100303 [...] $ Signed-off-by:
Michal Marek <mmarek@suse.cz> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-kbuild@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12537/Signed-off-by:
-
Jaedon Shin authored
Fixes wrong bcm7425 SATA AHCI hardware interrupt property value with periph_intc and SATA PHY unit address, and removes needless brcm,broken-{ncq,phy} properties what are not used anywhere. Signed-off-by:Jaedon Shin <jaedon.shin@gmail.com> Reviewed-by:
-
Jaedon Shin authored
Add UART, I2C, SATA device tree nodes on Broadcom BCM7xxx MIPS-based platforms. Signed-off-by:
-
Yang Shi authored
In Kconfig "=n" is not correct syntax, "!" is the preferred way for false-positive expression. Signed-off-by:
-
Matt Redfearn authored
When debugging a relocated kernel, the addresses of the relocated symbols and the offset applied is essential information. If the kernel is compiled with debugging information, then print this information during bootup using the same function as the panic notifier. [ralf@linux-mips.org: Fixed spelling mistake pointed out by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>.] Signed-off-by:
Matt Redfearn <matt.redfearn@imgtec.com> Cc: Aaro Koskinen <aaro.koskinen@nokia.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com> Cc: Jaedon Shin <jaedon.shin@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: kernel-hardening@lists.openwall.com Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12989/Signed-off-by:
-
Matt Redfearn authored
This patch adds KASLR to the MIPS kernel. Entropy is derived from the banner, which will change every build and random_get_entropy() which should provide additional runtime entropy. Additionally the bootloader may pass entropy via the /chosen/kaslr-seed node in device tree. The kernel is relocated by up to RANDOMIZE_BASE_MAX_OFFSET bytes from its link address (PHYSICAL_START). Because relocation happens so early in the kernel boot, the amount of physical memory has not yet been determined. This means the only way to limit relocation within the available memory is via Kconfig. Signed-off-by:
-
Matt Redfearn authored
Early access to the kernel command line requires early access to the FDT for platforms which pass the command line within the device tree. There was no common way to retrieve the location of the FDT without incurring side effects, such as plat_mem_setup which, on Malta at least, initializes a bunch of other stuff. This patch adds plat_get_ftd() for IMG platforms. Signed-off-by:
-
Matt Redfearn authored
Add option to KConfig to enable the kernel to relocate itself at runtime. Relocation is supported R2 and later of the MIPS architecture, 32bit and 64bit. The platform is also required to provide support through plat_get_fdt() added in a later patch. Signed-off-by:
-
Matt Redfearn authored
The kernel reserves all memory before the _end symbol as bootmem, however, once the kernel can be relocated elsewhere in memory this may result in a large amount of wasted memory. The assumption is that the memory between the link and relocated address of the kernel may be released back to the available memory pool. Memory statistics for a Malta with the kernel relocating by 16Mb, without the patch: Memory: 105952K/131072K available (4604K kernel code, 242K rwdata, 892K rodata, 1280K init, 183K bss, 25120K reserved, 0K cma-reserved) And with the patch: Memory: 122336K/131072K available (4604K kernel code, 242K rwdata, 892K rodata, 1280K init, 183K bss, 8736K reserved, 0K cma-reserved) The 16Mb offset is removed from the reserved region and added back to the available region. Signed-off-by:
-
Matt Redfearn authored
If CONFIG_RELOCATABLE is enabled, call relocate_kernel. This function will return the entry point of the relocated kernel if copy/relocate is sucessful or the original entry point if not. The stack pointer must then be pointed into the new image. Signed-off-by:
-
Matt Redfearn authored
arch/mips/kernel/relocate.c contains the functions necessary to relocate the kernel elsewhere in memory The kernel makes a copy of itself at the new address. It uses the relocation table inserted by the relocs tool to fix symbol references within the new image. If copy/relocation is sucessful then the entry point of the new kernel is returned, otherwise fall back to starting the kernel in place. Signed-off-by:
-
Matt Redfearn authored
When CONFIG_RELOCATABLE is enabled (added in later patch) add --emit-relocs to vmlinux LDFLAGS so that fully linked vmlinux contains relocation information. Run the previously added relocs tool to fill in the .data.relocs section of vmlinux with a table of relocations. The relocs tool will also remove (mark as 0 length) the relocation sections added to vmlinux. When vmlinux is passed to the boot makefile for conversion into a boot image the now empty relocation sections will be removed and the populated relocation table will be included in the binary image. Signed-off-by:
-
Matt Redfearn authored
When CONFIG_RELOCATABLE is enabled, add a new section in the memory map to be filled with relocation data. CONFIG_RELOCATION_TABLE_SIZE allows the amount of space reserved to be adjusted if necessary. The relocs tool will populate this reserved space with relocation information. The space is reserved within the elf by filling it with 0's, and an invalid entry is left at the start of the space such that kernel relocation will be aborted if the table is empty. Signed-off-by:
-
