Remove the cap IEEE80211_HT_CAP_DSSSCCK40 from the 5Ghz variant of
the siso40 HT capabilities. It is meaningless in 5Ghz.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Introduce a default set of HT capabilities that are set according to the
number of antennas on the board. Move the HT setting code down to allow
the number of antennas to be set (and optionally overridden) before it.

Remove the "mimo" HT option, since the default mode now enables MIMO is
possible.

Use this opportunity to add a helper function for setting HT
capabilities and reduce the volume of the code a bit.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The 18xx chip does not support MIMO in 5Ghz. Use the siso20 HT cap as
fallback in 5Ghz when "mimo" is requested.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

FW uses a few memory blocks as a buffer to accumulate FW logs before
transmitting them to the host over SDIO. When FW WatchDog recovery
occurs, the last FW traces are still pending in the buffer. Driver is
to read these FW traces whether log mode is continuous or on demand.

FW memory blocks allocated for the log buffer are handled as a link list:
the first 4 bytes in each memory block contain FW address to the next block.
The end of list condition depends on FW log mode:
- on demand: the list is cyclic, the next address is equal to the first address
- continuous: the address is  equal to 0x2000000

Log data resides inside FW memory block with offset depending on
logger mode:
- on demand:  4 bytes (address of the next memory block)
- continuous: 4 bytes and Rx Descriptor structure size

Described FW logger API is backward compatible with previous FW versions.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The get survey op expects the low level driver to report
the noise level for a a given channel.

The noise calculated in wlcore is (rssi-snr/2), but since
the snr reported by the FW is a derivative from the rssi
this calculation is useless, and should not be reported
to the user space.

Reporting incorrect noise, results in the wpa_supplicant
miscalculating the roaming candidate priority, thus causing
a situation where an AP with a lower rssi level would be
chosen over a better AP.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Before patch b5d6d9b (wlcore/wl12xx/wl18xx: don't use TX align quirk
for wl127x), this was automatically set for all platforms. As this
should now be set explicitly, set it for PG2 as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

New PG2 firmwares have additional Rx descriptors.

Add a module parameter to manually set the number of Rx descriptors for
older versions (PG1). We cannot discriminate based on chip-id, since
this value must be set on probe.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The sleep_auth value of the last interface to be set up prevailed when
an interface was removed. Take care of this by correctly configuring the
value according to the remaining STA/AP interfaces.

Take this opportunity to refactor the sleep_auth setting code for better
readability.

[Small style fix. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.

This makes debugging more intuitive using the debugfs value.

Increment the conf version since we added an element to the conf
structure.

Note: An AP going up will always set sleep_auth to PSM_CAM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

For FW debugging purposes, we may need to change the sleep mode
(aka. sleep_auth) by hand, and set it to the mode we want.  To allow
this, a debugfs entry is added.

Now we store the sleep_auth value that has been set and use that
instead of the quirk to decide whether we should enter ELP or not.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>

The ampdu_action() function is called on the reconfig() path to remove
existing Rx BA sessions. Since these don't exist for the low level
driver, we output an error message. Turn the message into a debug
message for now, until the mac80211 reconfig flow is changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Advertise to the stack that the wlcore driver
supports multiple interfaces for a single device.
This is required in order to be able to run
multirole with mac80211.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

FEM BIP calibration may fail with fw/phy radio status. In order to
recognize these failures a log is added to the calibration answer
(TEST_CMD_P2G_CAL)
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Add support for HP (High Performance TQS fem type 3) and SKW
(fem type 2). This is done by increasing the number of FEM
manufacturers to 4.

Usually FEM parameters from ini file are read from nvs file and
passed to firmware using TEST_CMD_INI_FILE_RADIO_PARAM. Still,
because the nvs file has only place for 2 FEMs, we need to pass the
new FEM types information in one of the available entries.

This is done by mapping new fem types 2,3 to entry 0. This solution
works for manual FEM selection. AutoDetect-FEM still support only
fem types 0 and 1.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

On channel switch we have to update the basic rates, in
order to reflect possible band changes (otherwise, we
might start beaconing on 11a with the default rates
of 11g).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

EAPOLs are sent at high rates as they are considered
data packets. Some APs like Motorola Symbol AP7131 and AP650
don't respond well to these rates and don't respond with
EAPOL 3/4 consistently. When sending EAPOL 2/4 at 54Mbps
we've seen approx 30% success rate in getting EAPOL 3/4 response
while using 11Mbps we got 100% success.
To increase the chances of successful 4-Way handshake with
such APs, send EAPOLs with basic rate policy in order to avoid
high rates.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

NET_IP_ALIGN can be overriden on different architectures
and therefore cannot be used in the RX path to account
for the 2 bytes added for alignment (either by the FW
in the case of 18xx or by the host for 12xx).
Instead use an internal define.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Don't spew errors when we can't find the NVS file in wlcore. Instead
fail the wl12xx boot HW op if the NVS isn't found.

Take this opportunity to remove some dead code from register_hw()
which looks for the NVS again needlessly.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Give all wl18xx phy module paramters -1 as a default value, indicating
the paramter was not set. Add previous default values to the default
18xx priv conf structure.

Remove the board_type field from wl18xx priv. The field with the same
name inside the phy conf is good enough for our purposes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params
structure. Remove it and replace the phy part of the wl18xx conf with the
FW bound structure. This allows us to set/override all members.

Increment the wlconf version to ensure compatibility with the new
structure
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Aligned to the struct in FW 8.2.0.0.91 and updated the debugfs entries
accordingly.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

This is supported by new FW versions (.88+).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Instead of using the hardcoded configuration structure, try to read it
from a "firmware" file called wl18xx-conf.bin.  If the file doesn't
exist, fall back to the hardcoded version.  If the file exists but is
illegal, bail out.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Add conf file header structure, magic and version values and export
the entire conf struct in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Since we are now going to export the conf structure and read it from a
file, it should be packed to avoid surprises with padding bytes.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Since we will export the conf structure as a file, we need to use well
defined types.  Instead of using enum, whose size may vary, use u8 for
bcn_filt_mode instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>

The conf structure is going to be exported to a file, so we should use
only well defined types.  bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Instead of parsing all the binary data returned by the firmware, we
should simply export the binary and let the userspace do the parsing.

This commit adds a new file to debugfs to do that.
Signed-off-by: Luciano Coelho <coelho@ti.com>

This patch calls ACX_CLEAR_STATISTICS to clear the firmware
statistics.  The trigger is a new debugfs file called
clear_fw_statistics in the fw_stats directory.
Signed-off-by: Luciano Coelho <coelho@ti.com>

Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Add support for an external 26 MHz crystal source.

[Changed wl->ref_clock to priv->ref_clock -- Luca.]
Signed-off-by: Grant Erickson <marathon96@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.

[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]

[Make the pre_pkt_send operation optional -- Luca]
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).

[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]
Signed-off-by: Orit Brayer <orit@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

PG2 requires 4 new parameters that to be passed to the PHY.

Use the actual PHY initialization struct size for the mem size of the
PHY_INIT section, to account for additions in params.

[Make sure PG1 still gets the original struct - Arik]
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

PG2 has a unique chip id. It supports similar HW quirks.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

was hardcoded 252, now uses the parameters struct size.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Introduce “pactive” scan mode – which instructs the fw to
perform a passive scan until an activity/energy is detected
on these channels, once energy detected the channel becomes
active.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

When comparing 2 ssids the ssid_len must be taken
into account. Otherwise, a substring will be treated
as equal.

This bug might cause ssids to get scanned as
public ssids (rather than hidden), resulting in
broadcast probe request (instead of ssid-specific
ones)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Due to a need by the firmware when working in multirole
the role id needs to be added to the structs of the
following commands:
CMD_CONNECTION_SCAN_CFG, CMD_CONNECTION_SCAN_SSID_CFG,
CMD_START_PERIODIC_SCAN, CMD_STOP_PERIODIC_SCAN
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>