If an rdma_cm_id is bound to AF_IB, with a wild card address, only
listen on IB devices.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Allow the user to specify the qkey when using AF_IB.  The qkey is
added to struct rdma_ucm_conn_param in place of a reserved field, but
for backwards compatability, is only accessed if the associated
rdma_cm_id is using AF_IB.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

If the source or destination address is AF_IB, then do not reserve a
portion of the private data in the IB CM REQ or SIDR REQ messages for
the cma header.  Instead, all private data should be exported to the
user.  When AF_IB is used, the rdma cm does not have sufficient
information to fill in the cma header.  Additionally, this will be
necessary to support any IB connection through the rdma cm interface,
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

With the removal of SDP related code, we can merge cma_get_net_info()
with cma_save_net_info(), since we're only ever dealing with a single
header format.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

The SDP protocol was never merged upstream.  Remove unused SDP related
code from the RDMA CM.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

cma_get_service_id() forms the service ID based on the port space and
port number of the rdma_cm_id.  Extend the call to support AF_IB,
which contains the service ID directly.  This will be needed to
support any arbitrary SID.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Allow rdma_resolve_route() to handle the case where the user specified
the source and destination addresses using AF_IB.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Allow the user to specify the remote address using AF_IB format.  When
AF_IB is used, the remote address simply needs to be recorded, and no
resolution using ARP is done.  The local address may still need to be
matched with a local IB device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

If a user specifies AF_IB as the source address for a loopback
connection, limit the resolution to IB devices only.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Provide inline helpers to extract source and destination address data
from the rdma_cm_id.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

cma_resolve_loopback is called after an rdma_cm_id has been
bound to a specific sa_family and port.  Once the
source sa_family for the id has been set, do not modify it.
Only the actual IP address portion of the source address
needs to be set.

As part of this fix, we can simplify setting the source address
by moving the loopback address assignment from cma_resolve_loopback
to cma_bind_loopback.  cma_bind_loopback is only invoked when
the source address is the loopback address.

Finally, add loopback support for AF_IB as part of the change.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Modify rdma_bind_addr to allow the user to specify AF_IB when binding
to a device.  AF_IB indicates that the user is not mapping an IP
address to the native IB addressing.  (The mapping may have already
been done, or is not needed)
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

The AF_IB uses a 64-bit service id (SID), which the user can control
through the use of a mask.  The rdma_cm will assign values to the
unmasked portions of the SID based on the selected port space and port
number.

Because the IB spec divides the SID range into several regions, a
SID/mask combination may fall into one of the existing port space
ranges as defined by the RDMA CM IP Annex.  Map the AF_IB SID to the
correct RDMA port space.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Add support for AF_IB to ip_addr_size, and rename the function to
account for the change.  Give the compiler more control over whether
the call should be inline or not by moving the definition into the .c
file, removing the static inline, and exporting it.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Enhance checks for loopback and any address to support AF_IB in
addition to AF_INET and AF_INT6.  This will allow future patches to
use AF_IB when binding and resolving addresses.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

The rdma_cm only allows setting reuseaddr if the corresponding
rdma_cm_id is in the idle state.  Allow setting this value in other
states.  This brings the behavior more inline with sockets.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

Define AF_IB and sockaddr_ib to allow the rdma_cm to use native IB
addressing.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>

This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes an empty ifdef from inet_frag_intern()
in net/ipv4/inet_fragment.c.

commit b67bfe0d
(hlist: drop the node parameter from iterators) removed hlist from
net/ipv4/inet_fragment.c, but did not remove the enclosing ifdef command,
which is now empty.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

htb_sched structures are big, and source of false sharing on SMP.

Every time a packet is queued or dequeue, many cache lines must be
touched because structures are not lay out properly.

By carefully splitting htb_sched in two parts, and define sub structures
to increase data locality, we can improve performance dramatically on
SMP.

New htb_prio structure can also be used in htb_class to increase data
locality.

I got 26 % performance increase on a 24 threads machine, with 200
concurrent netperf in TCP_RR mode, using a HTB hierarchy of 4 classes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous discussions, I tried to find some reasonable heuristics
for delayed ACK, however this seems not possible, according to Eric:

	"ACKS might also be delayed because of bidirectional
	traffic, and is more controlled by the application
	response time. TCP stack can not easily estimate it."

	"ACK can be incredibly useful to recover from losses in
	a short time.

	The vast majority of TCP sessions are small lived, and we
	send one ACK per received segment anyway at beginning or
	retransmits to let the sender smoothly increase its cwnd,
	so an auto-tuning facility wont help them that much."

and according to David:

	"ACKs are the only information we have to detect loss.

	And, for the same reasons that TCP VEGAS is fundamentally
	broken, we cannot measure the pipe or some other
	receiver-side-visible piece of information to determine
	when it's "safe" to stretch ACK.

	And even if it's "safe", we should not do it so that losses are
	accurately detected and we don't spuriously retransmit.

	The only way to know when the bandwidth increases is to
	"test" it, by sending more and more packets until drops happen.
	That's why all successful congestion control algorithms must
	operate on explicited tested pieces of information.

	Similarly, it's not really possible to universally know if
	it's safe to stretch ACK or not."

It still makes sense to enable or disable quick ack mode like
what TCP_QUICK_ACK does.

Similar to TCP_QUICK_ACK option, but for people who can't
modify the source code and still wants to control
TCP delayed ACK behavior. As David suggested, this should belong
to per-path scope, since different pathes may want different
behaviors.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pci core has been saved pm cap register offset by pdev->pm_cap in pci_pm_init()
in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Pci core has been saved pm cap register offset by pdev->pm_cap in pci_pm_init()
in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: netdev@vger.kernel.org (open list:NETWORKING DRIVERS)
Signed-off-by: David S. Miller <davem@davemloft.net>

Pci_enable_device() will set device power state to D0,
so it's no need to do it again in bnx2x_init_dev().
Also remove redundant PM Cap find code, because pci core
has been saved the pci device pm cap value.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ETRAX_ETHERNET selects ETHERNET and MII, which depend on NETDEVICES.
I don't think anything should select NETDEVICES, so make it a
dependency.  It also doesn't need to select or depend on ETHERNET,
which has nothing to do with the Ethernet library functions.

BPCTL selects MII, which depends on NETDEVICES.  But everything in the
drivers/staging/silicom directory is related to net devices, so make
NET_VENDOR_SILICOM depend on NETDEVICES and remove the now-redundant
dependencies on NET.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This has no dependency on any of the drivers under NET_CORE.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All drivers that select MII also need to select NET_CORE because MII
depends on it.  This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.

There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Also, cleanup bond_alb_handle_active_change() from 2 identical ifs.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be_find_vfs() is no longer needed as the common PCI calls provide the same
functionality.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The use of this attribute has been added in 32b8a8e5 (sit: add IPv4 over
IPv4 support). It is optional, by default proto is IPPROTO_IPV6.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current situation is that SOCK_MIN_RCVBUF is 2048 + sizeof(struct sk_buff))
while SOCK_MIN_SNDBUF is 2048. Since in both cases, skb->truesize is used for
sk_{r,w}mem_alloc accounting, we should have both sizes adjusted via defining a
TCP_SKB_MIN_TRUESIZE.

Further, as Eric Dumazet points out, the minimal skb truesize in transmit path is
SKB_TRUESIZE(2048) after commit f07d960d ("tcp: avoid frag allocation for
small frames"), and tcp_sendmsg() tries to limit skb size to half the congestion
window, meaning we try to build two skbs at minimum. Thus, having SOCK_MIN_SNDBUF
as 2048 can hit a small regression for some applications setting to low
SO_SNDBUF / SO_RCVBUF. Note that we define a TCP_SKB_MIN_TRUESIZE, because
SKB_TRUESIZE(2048) adds SKB_DATA_ALIGN(sizeof(struct skb_shared_info)), but in
case of TCP skbs, the skb_shared_info is part of the 2048 bytes allocation for
skb->head.

The minor adaption in sk_stream_moderate_sndbuf() is to silence a warning by
using a typed max macro, as similarly done in SOCK_MIN_RCVBUF occurences, that
would appear otherwise.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

thresh and interval are global resources,
only init net can change them.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Though we don't export the /proc/sys/net/ipv[4,6]/neigh/default/
directory to the un-init_net, but we can still use cmd such as
"ip ntable change name arp_cache locktime 129" to change the locktime
of default neigh_parms.

This patch disallows the un-init_net to find out the neigh_table.parms.
So the un-init_net will failed to influence the init_net.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh_table.parms always exist and is initialized,kmemdup
can use it to create new neigh_parms, actually lookup_neigh_parms
here will return neigh_table.parms too.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check next packet availability by validating that HW has finished CQE
placement. This saves latency of another dma transaction performed to update
SB indexes.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds ndo_ll_poll method and locking for FPs between LL and the napi.

When receiving a packet we use skb_mark_ll to record the napi it came from.
Add each napi to the napi_hash right after netif_napi_add().
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>