- 04 Oct, 2019 16 commits
-
-
David S. Miller authored
Jiri Pirko says: ==================== devlink: allow devlink instances to change network namespace Devlink from the beginning counts with network namespaces, but the instances has been fixed to init_net. Implement change of network namespace as part of "devlink reload" procedure like this: $ ip netns add testns1 $ devlink/devlink dev reload netdevsim/netdevsim10 netns testns1 This command reloads device "netdevsim10" into network namespace "testns1". Note that "devlink reload" reinstantiates driver objects, effectively it reloads the driver instance, including possible hw reset etc. Newly created netdevices respect the network namespace of the parent devlink instance and according to that, they are created in target network namespace. Driver is able to refuse to be reloaded into different namespace. That is the case of mlx4 right now. FIB entries and rules are replayed during FIB notifier registration which is triggered during reload (driver instance init). FIB notifier is also registered to the target network namespace, that allows user to use netdevsim devlink resources to setup per-namespace limits of FIB entries and FIB rules. In fact, with multiple netdevsim instances in each network namespace, user might setup different limits. This maintains and extends current netdevsim resources behaviour. Patch 1 prepares netdevsim code for the follow-up changes in the patchset. It does not change the behaviour, only moves pet-init_netns accounting to netdevsim instance, which is also in init_netns. Patches 2-5 prepare the FIB notifier making it per-netns and to behave correctly upon error conditions. Patch 6 just exports a devlink_net helper so it can be used in drivers. Patches 7-9 do preparations in mlxsw driver. Patches 10-13 do preparations in netdevsim driver, namely patch 12 implements proper devlink reload where the driver instance objects are actually re-created as they should be. Patch 14 actually implements the possibility to reload into a different network namespace. Patch 15 adds needed selftests for devlink reload into namespace for netdevsim driver. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
Add couple of tests for devlink reload testing and also resource limitations testing, along with devlink reload. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Jiri Pirko authored
All devlink instances are created in init_net and stay there for a lifetime. Allow user to be able to move devlink instances into namespaces during devlink reload operation. That ensures proper re-instantiation of driver objects, including netdevices. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Jiri Pirko authored
Follow-up patch is going to allow to reload devlink instance into different network namespace, so use devlink_net() helper instead of init_net. Signed-off-by:
-
Jiri Pirko authored
Register newly created port netdevice into net namespace that the parent device belongs to. Signed-off-by:
-
Jiri Pirko authored
During devlink reload, all driver objects should be reinstantiated with the exception of devlink instance and devlink resources and params. Move existing devlink_resource_size_get() calls into fib_create() just before fib notifier is registered. Also, make sure that extack is propagated down to fib_notifier_register() call. Signed-off-by:
-
Jiri Pirko authored
Currently the probe/remove function does this separately. Put the addition an deletion of ports into nsim_dev_create() and nsim_dev_destroy(). Signed-off-by:
-
Jiri Pirko authored
During the devlink reaload the extack is present, so propagate it all the way down to register_fib_notifier() call in spectrum_router.c. Signed-off-by:
-
Jiri Pirko authored
When creating netdevices for ports, put them under network namespace that the core/parent devlink belongs to. Signed-off-by:
-
Jiri Pirko authored
Follow-up patch is going to allow to reload devlink instance into different network namespace, so use devlink_net() helper instead of init_net. Signed-off-by:
-
Jiri Pirko authored
Allow drivers to get net struct for devlink instance. Signed-off-by:
-
Jiri Pirko authored
Since errors are propagated all the way up to the caller, propagate possible extack of the caller all the way down to the notifier block callback. Signed-off-by:
-
Jiri Pirko authored
Currently if info->extack is NULL, mlxsw assumes that the event came down from dump. Originally, the dump did not propagate the return value back to the original caller (fib_notifier_register()). However, that is now happening. So benefit from this and push the error up if it happened. Remove rule cases in work handlers that are now dead code. Signed-off-by:
-
Jiri Pirko authored
Unlike events for registered notifier, during the registration, the errors that happened for the block being registered are not propagated up to the caller. Make sure the error is propagated for FIB rules and entries. Signed-off-by:
-
Jiri Pirko authored
Currently all users of FIB notifier only cares about events in init_net. Later in this patchset, users get interested in other namespaces too. However, for every registered block user is interested only about one namespace. Make the FIB notifier registration per-netns and avoid unnecessary calls of notifier block for other namespaces. Signed-off-by:
-
Jiri Pirko authored
Currently, the accounting is done per-namespace. However, devlink instance is always in init_net namespace for now, so only the accounting related to init_net is used. Limitations set using devlink resources are only considered for init_net. nsim_devlink_net() always returns init_net always. Make the accounting per-device. This brings no functional change. Per-device accounting has the same values as per-net. For a single netdevsim instance, the behaviour is exactly the same as before. When multiple netdevsim instances are created, each can have different limits. This is in prepare to implement proper devlink netns support. After that, the devlink instance which would exist in particular netns would account and limit that netns. Signed-off-by:
-
- 03 Oct, 2019 10 commits
-
-
Eric Dumazet authored
If netdev_name_node_head_alloc() fails to allocate memory, we absolutely want register_netdevice() to return -ENOMEM instead of zero :/ One of the syzbot report looked like : general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 8760 Comm: syz-executor839 Not tainted 5.3.0+ #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:ovs_vport_add+0x185/0x500 net/openvswitch/vport.c:205 Code: 89 c6 e8 3e b6 3a fa 49 81 fc 00 f0 ff ff 0f 87 6d 02 00 00 e8 8c b4 3a fa 4c 89 e2 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 d3 02 00 00 49 8d 7c 24 08 49 8b 34 24 48 b8 00 RSP: 0018:ffff88808fe5f4e0 EFLAGS: 00010247 RAX: dffffc0000000000 RBX: ffffffff89be8820 RCX: ffffffff87385162 RDX: 0000000000000000 RSI: ffffffff87385174 RDI: 0000000000000007 RBP: ffff88808fe5f510 R08: ffff8880933c6600 R09: fffffbfff14ee13c R10: fffffbfff14ee13b R11: ffffffff8a7709df R12: 0000000000000004 R13: ffffffff89be8850 R14: ffff88808fe5f5e0 R15: 0000000000000002 FS: 0000000001d71880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000280 CR3: 0000000096e4c000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: new_vport+0x1b/0x1d0 net/openvswitch/datapath.c:194 ovs_dp_cmd_new+0x5e5/0xe30 net/openvswitch/datapath.c:1644 genl_family_rcv_msg+0x74b/0xf90 net/netlink/genetlink.c:629 genl_rcv_msg+0xca/0x170 net/netlink/genetlink.c:654 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477 genl_rcv+0x29/0x40 net/netlink/genetlink.c:665 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0x531/0x710 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x8a5/0xd60 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:637 [inline] sock_sendmsg+0xd7/0x130 net/socket.c:657 ___sys_sendmsg+0x803/0x920 net/socket.c:2311 __sys_sendmsg+0x105/0x1d0 net/socket.c:2356 __do_sys_sendmsg net/socket.c:2365 [inline] __se_sys_sendmsg net/socket.c:2363 [inline] __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2363 Fixes: ff927412 ("net: introduce name_node struct to be used in hashlist") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jiri@mellanox.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Tested-by:
Willem de Bruijn <willemb@google.com> Reviewed-by:
-
David S. Miller authored
Oleksij Rempel says: ==================== phy: at803x: add ar9331 support changes v3: - use PHY_ID_MATCH_EXACT only for ATH9331 PHY changes v2: - use PHY_ID_MATCH_EXACT instead of leaky masking - remove probe and struct at803x_priv ==================== Signed-off-by: -
Oleksij Rempel authored
struct at803x_priv is never used in this driver. So remove it and the probe function allocating it. Suggested-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
-
Oleksij Rempel authored
Mostly this hardware can work with generic PHY driver, but this change is needed to provided interrupt handling support. Tested with dsa ar9331-switch driver. Signed-off-by:
-
Petr Machata authored
Currently mlxsw distributes sent traffic among all the available send queues. That includes control traffic as well as EMADs, which are used for configuration of the device. However because all the queues have the same traffic class of 3, they all end up being directed to the same traffic class buffer. If the control traffic in the buffer cannot be serviced quickly enough, the EMAD traffic might be shut out, which causes transient failures, typically in FDB maintenance, counter upkeep and other periodic work. To address this issue, dedicate SDQ 0 to EMAD traffic, with TC 0. Distribute the control traffic among the remaining queues, which are left with their current TC 3. Suggested-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Petr Machata <petrm@mellanox.com> Acked-by:
-
Ka-Cheong Poon authored
Currently, RDS calls ib_dma_alloc_coherent() to allocate a large piece of contiguous DMA coherent memory to store struct rds_header for sending/receiving packets. The memory allocated is then partitioned into struct rds_header. This is not necessary and can be costly at times when memory is fragmented. Instead, RDS should use the DMA memory pool interface to handle this. The DMA addresses of the pre- allocated headers are stored in an array. At send/receive ring initialization and refill time, this arrary is de-referenced to get the DMA addresses. This array is not accessed at send/receive packet processing. Suggested-by:
Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by:
Ka-Cheong Poon <ka-cheong.poon@oracle.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
David S. Miller authored
Thierry Reding says: ==================== net: stmmac: Enhanced addressing mode for DWMAC 4.10 The DWMAC 4.10 supports the same enhanced addressing mode as later generations. Parse this capability from the hardware feature registers and set the EAME (Enhanced Addressing Mode Enable) bit when necessary. ==================== Signed-off-by: -
Thierry Reding authored
The address width of the controller can be read from hardware feature registers much like on XGMAC. Add support for parsing the ADDR64 field so that the DMA mask can be set accordingly. This avoids getting swiotlb involved for DMA on Tegra186 and later. Also make sure that the upper 32 bits of the DMA address are written to the DMA descriptors when enhanced addressing mode is used. Similarily, for each channel, the upper 32 bits of the DMA descriptor ring's base address also need to be programmed to make sure the correct memory can be fetched when the DMA descriptor ring is located beyond the 32-bit boundary. Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Thierry Reding authored
Enhanced addressing mode is only required when more than 32 bits need to be addressed. Add a DMA configuration parameter to enable this mode only when needed. Signed-off-by:
-
Prashant Malani authored
Checkpatch throws warnings for function pointer declarations which lack identifier names. An example of such a warning is: WARNING: function definition argument 'struct r8152 *' should also have an identifier name 739: FILE: drivers/net/usb/r8152.c:739: + void (*init)(struct r8152 *); So, fix those warnings by adding the identifier names. While we are at it, also fix a character limit violation which was causing another checkpatch warning. Change-Id: Idec857ce2dc9592caf3173188be1660052c052ce Signed-off-by:
Prashant Malani <pmalani@chromium.org> Reviewed-by:
Grant Grundler <grundler@chromium.org> Acked-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
- 02 Oct, 2019 14 commits
-
-
Sudhakar Dindukurti authored
Log vendor error if work requests fail. Vendor error provides more information that is used for debugging the issue. Signed-off-by:
Sudhakar Dindukurti <sudhakar.dindukurti@oracle.com> Acked-by:
-
Matteo Croce authored
Recycling in mvpp2 has gone long time ago, but two comment still refers to it. Remove those two misleading comments as they generate confusion. Fixes: 7ef7e1d9 ("net: mvpp2: drop useless fields in mvpp2_bm_pool and related code") Signed-off-by:
Matteo Croce <mcroce@redhat.com> Signed-off-by:
-
David S. Miller authored
Randy Dunlap says: ==================== CAIF Kconfig fixes This series of patches cleans up the CAIF Kconfig menus in net/caif/Kconfig and drivers/net/caif/Kconfig and also puts the CAIF Transport drivers into their own sub-menu. ==================== Signed-off-by: -
rd.dunlab@gmail.com authored
Minor fixes to the CAIF Transport drivers Kconfig file: - end sentence with period - capitalize CAIF acronym Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
rd.dunlab@gmail.com authored
Isolate CAIF transport drivers into their own menu. This cleans up the main Network device support menu, makes it easier to find the CAIF drivers, and makes it easier to enable/disable them as a group. Signed-off-by:
-
rd.dunlab@gmail.com authored
Clean up the net/caif/Kconfig menu: - remove extraneous space - minor language tweaks - fix punctuation Signed-off-by:
-
Eric Dumazet authored
The introduction of this schedule point was done in commit 2ba2506c ("[NET]: Add preemption point in qdisc_run") at a time the loop was not bounded. Then later in commit d5b8aa1d ("net_sched: fix dequeuer fairness") we added a limit on the number of packets. Now is the time to remove the schedule point, since the default limit of 64 packets matches the number of packets a typical NAPI poll can process in a row. This solves a latency problem for most TCP receivers under moderate load : 1) host receives a packet. NET_RX_SOFTIRQ is raised by NIC hard IRQ handler 2) __do_softirq() does its first loop, handling NET_RX_SOFTIRQ and calling the driver napi->loop() function 3) TCP stores the skb in socket receive queue: 4) TCP calls sk->sk_data_ready() and wakeups a user thread waiting for EPOLLIN (as a result, need_resched() might now be true) 5) TCP cooks an ACK and sends it. 6) qdisc_run() processes one packet from qdisc, and sees need_resched(), this raises NET_TX_SOFTIRQ (even if there are no more packets in the qdisc) Then we go back to the __do_softirq() in 2), and we see that new softirqs were raised. Since need_resched() is true, we end up waking ksoftirqd in this path : if (pending) { if (time_before(jiffies, end) && !need_resched() && --max_restart) goto restart; wakeup_softirqd(); } So we have many wakeups of ksoftirqd kernel threads, and more calls to qdisc_run() with associated lock overhead. Note that another way to solve the issue would be to change TCP to first send the ACK packet, then signal the EPOLLIN, but this changes P99 latencies, as sending the ACK packet can add a long delay. Signed-off-by:
-
Vladimir Oltean authored
The struct __dsa_skb_cb is supposed to span the entire 48-byte skb control block, while the struct dsa_skb_cb only the portion of it which is used by the DSA core (the rest is available as private data to drivers). The DSA_SKB_CB and __DSA_SKB_CB helpers are supposed to help retrieve this pointer based on a skb, but it turns out there is nobody directly interested in the struct __dsa_skb_cb in the kernel. So remove it. Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== SJA1105 DSA coding style cleanup This series provides some mechanical cleanup patches related to function names and prototypes. ==================== Signed-off-by: -
Vladimir Oltean authored
The most commonly called function in the driver is long due for a rename. The "packed" word is redundant (it doesn't make sense to transfer an unpacked structure, since that is in CPU endianness yadda yadda), and the "spi" word is also redundant since argument 2 of the function is SPI_READ or SPI_WRITE. As for the sja1105_spi_send_long_packed_buf function, it is only being used from sja1105_spi.c, so remove its global prototype. Signed-off-by:
-
Vladimir Oltean authored
Having a function that takes a variable number of unpacked bytes which it generically calls an "int" is confusing and makes auditing patches next to impossible. We only use spi_send_int with the int sizes of 32 and 64 bits. So just make the spi_send_int function less generic and replace it with the appropriate two explicit functions, which can now type-check the int pointer type. Note that there is still a small weirdness in the u32 function, which has to convert it to a u64 temporary. This is because of how the packing API works at the moment, but the weirdness is at least hidden from callers of sja1105_xfer_u32 now. Suggested-by:
-
Vladimir Oltean authored
Let the compiler decide. Signed-off-by:
-
David S. Miller authored
Paulo Alcantara says: ==================== Experimental SMB rootfs support This patch series enables Linux to mount root file systems over the network by utilizing SMB protocol. Upstream commit 8eecd1c2 ("cifs: Add support for root file systems") introduced a new CONFIG_CIFS_ROOT option, a virtual device (Root_CIFS) and a kernel cmdline parameter "cifsroot=" which tells the kernel to actually mount the root filesystem over a SMB share. The feature relies on ipconfig to set up the network prior to mounting the rootfs, so when it is set along with "cifsroot=" parameter: (1) cifs_root_setup() parses all necessary data out of "cifsroot=" parameter for the init process know how to mount the SMB rootfs (e.g. SMB server address, mount options). (2) If DHCP failed for some reason in ipconfig, we keep retrying forever as we have nowhere to go for NFS or SMB root filesystems (see PATCH 2/2). Otherwise go to (3). (3) mount_cifs_root() is then called by mount_root() (ROOT_DEV == Root_CIFS), retrieves early parsed data from (1), then attempt to mount SMB rootfs by CIFSROOT_RETRY_MAX times at most (see PATCH 1/2). (4) If all attempts failed, fall back to floppy drive, otherwise continue the boot process with rootfs mounted over a SMB share. My idea was to keep the same behavior of nfsroot - as it seems to work for most users so far. For more information on how this feature works, see Documentation/filesystems/cifs/cifsroot.txt. ==================== Signed-off-by:
-
Paulo Alcantara (SUSE) authored
The experimental root file system support in cifs.ko relies on ipconfig to set up the network stack and then accessing the SMB share that contains the rootfs files. Signed-off-by:
Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by:
-
