- Make sure that coprocessor instructions for range ops are contiguous
  and not reordered.

- s/invalidate_and_disable_dcache/flush_and_disable_dcache/

- Don't re-enable I/D caches if they were not enabled initially.

- Change some masks to shifts for better generated code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>

This patch adds specific power-off method for Buffalo Linkstation Mini
board. The board has a hardware switch which should be monitored from
userspace. When the switch is in OFF position the board should be rebooted
and U-Boot will start in an idle mode and wait for the user to move the
power switch back to ON position.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

This patch adds support for Buffalo Linkstation Mini board.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

Feroceon L2 cache can work in eighther write through or write back mode
on Kirkwood. Add the option to configure this mode according to Kconfig.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

This patch provides standard GPIO LED control
for the ED Mini V2, with software blinking only
(CPLD hardware blinking capability is not used).

This patch also provides status of the power
button as a standard GPIO input event.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Remove uart1 init calls for boards that use the physical pins onto
which the UART1 signals are multiplexed for different purposes.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Add support to the Kirkwood port for newer device models and silicon
revisions.  Instead of looking at the DEVICE_ID register, the device
version is now determined by looking at the PCI-Express device ID and
revision registers, as it is done for orion5x, and this information
is used to determine the TCLK frequency, again, as it is done for
orion5x.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Currently, kirkwood uses a hardcoded timer tick rate of 166 MHz, but
the actual timer tick rate varies between different members of the SoC
family.

This patch prepares for runtime determination of the timer tick rate.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>

The RD88F6183AP-GE is an access point reference design for the
88F6183 SoC, with a 88E6161 six-port gigabit ethernet switch with
five PHYs (providing 1 WAN and 4 LAN ports and an interface to the
CPU), and a mini-PCIe slot for a wireless card.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

The Orion-1-90 (88F6183) is another member of the Orion SoC family,
which has a 16 bit DDR2 interface, one x1 PCIe port (configurable as
Root Complex or Endpoint), one 10/100/1000 ethernet interface, one
USB 2.0 port with PHY, one SPDIF/I2S interface, one SDIO interface,
one TWSI interface, two UARTs, one SPI interface, a NAND controller,
a crypto engine, and a 4-channel DMA engine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

This patch adds support for the Buffalo Terastation Pro II/Live.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

This patch adds support for the LaCie Ethernet Disk mini V2.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Currently, orion5x uses a hardcoded timer tick rate of 166 MHz, but
the actual timer tick rate varies between different members of the SoC
family (and can vary based on strap pin settings).

This patch prepares for runtime determination of the timer tick rate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  bnx2x: Version update
  bnx2x: Multi Queue
  bnx2x: NAPI and interrupts enable/disable
  bnx2x: NIC load failure cleanup
  bnx2x: Initialization structure
  bnx2x: HW lock timeout
  bnx2x: Minimize lock time
  bnx2x: Fan failure mechanism on additional design
  bnx2x: Rx work check
  ipv6: sysctl fixes
  ipv4: sysctl fixes
  sctp: add verification checks to SCTP_AUTH_KEY option

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Version update
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The multi queue support is still disabled by default for the bnx2x
(needs some more testing and validation), but there are 2 obvious bug in
it which are fixed in this patch
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixing the order of enabling and disabling NAPI and the interrupts
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Load failures were not handled correctly
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TPA initialization is part of the FW internal memory initialization
and so it is moved to the appropriate function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increasing the lock timeout to 5 seconds instead of 1 second to minimize
the chance of failures due to timeout
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After iSCSI boot, the HW lock should only protect the flag so only the
first function will reset the chip and not then entire chip reset
process
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The A1021G board is also using the fan failure mechanism in the same way
the A1022G board does
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The has Rx work check was wrong: when the FW was at the end of the page,
the driver was already at the beginning of the next page. Since the
check only validated that both driver and FW are pointing to the same
place, it concluded that there is still work to be done. This caused
some serious issues including long latency results on ping-pong test and
lockups while unloading the driver in that condition.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Braino: net.ipv6 in ipv6 skeleton has no business in rotable
class
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net.ipv4.neigh should be a part of skeleton to avoid ordering problems
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The structure used for SCTP_AUTH_KEY option contains a
length that needs to be verfied to prevent buffer overflow
conditions.  Spoted by Eugene Teo <eteo@redhat.com>.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a regression that was indirectly caused by commit
1184dc2f ("x86: modify Kconfig to allow
up to 4096 cpus").

Allowing 4k CPU's is not practical at this time, because we still have a
number of places that have several 'cpumask_t's on the stack, and a
4k-bit cpumask is 512 bytes of stack-space for each such variable.  This
literally caused functions like 'smp_call_function_mask' to have a 2.5kB
stack frame, and several functions to have 2kB stackframes.

With an 8kB stack total, smashing the stack was simply much too likely.
At least bugzilla entry

	http://bugzilla.kernel.org/show_bug.cgi?id=11342

was due to this.

The earlier commit to not inline load_module() into sys_init_module()
fixed the particular symptoms of this that Alan Brunelle saw in that
bugzilla entry, but the huge stack waste by cpumask_t's was the more
direct cause.

Some day we'll have allocation helpers that allocate large CPU masks
dynamically, but in the meantime we simply cannot allow cpumasks this
large.

Cc: Alan D. Brunelle <Alan.Brunelle@hp.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rtc: fix deadlock

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: add X86_FEATURE_XMM4_2 definitions
  x86: fix cpufreq + sched_clock() regression
  x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
  x86: do not enable TSC notifier if we don't need it
  x86 MCE: Fix CPU hotplug problem with multiple multicore AMD CPUs
  x86: fix: make PCI ECS for AMD CPUs hotplug capable
  x86: fix: do not run code in amd_bus.c on non-AMD CPUs

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched_clock: fix cpu_clock()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: fix reference leak in pci_get_dev_by_id()
  PCI: shpchp: Rename duplicate slot name N as N-1, N-2, N-M...
  PCI: pciehp: Rename duplicate slot name N as N-1, N-2, N-M...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ASoC: Fix double free and memory leak in many codec drivers
  ALSA: CA0106 on MSI K8N Diamond PLUS Motherboard

* 'kvm-updates-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
  KVM: fix userspace ABI breakage
  KVM: MMU: Fix torn shadow pte
  KVM: Use .fixup instead of .text.fixup on __kvm_handle_fault_on_reboot

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  lguest: update commentry
  stop_machine: Remove deprecated stop_machine_run
  stop_machine: wean Xen off stop_machine_run
  virtio_balloon: fix towards_target when deflating balloon